Product

Planar-Doped Barrier Diode Detector, 0.01 to 33 GHz

8474C

-

Keysight Technologies

8474C - Keysight Technologies

The Keysight 8474C is a high-performance detector using a gallium arsenide, planar-doped barrier detecting element. It features extremely flat frequency response over its entire band of operation and very good frequency response stability versus temperature. The Keysight 8474C is also very rugged with high resistance to ESD damage. The Keysight 8474C detector is available with a 3.5-mm (mates with SMA, 0.01 to 33 GHz) connector. This detector offers the options for optimal sqaure-law loads (Option 102) and for positive polarity output (option 103). Because the unit-to-unit frequency response tracking of this device is typically better than 0.3 dB, no matched response option is offered.

Product

Blemish Checker For FPD

NM Series

-

Toray Engineering Co., Ltd.

NM Series - Toray Engineering Co., Ltd.

Detecting failures and uneven points on color resist film coated by Toray’s Coater. Toray’s customized algorithm achieved fast throughput and high resolution.

Product

Motor Starting & Control Resistors

-

Hilkar

Hilkar

Motor Starting Resistors are used to reduce the voltage at the motor terminals and also decrease the starting current. Motor Starting Resistors are necessary because the self resistance of a motor armature is very low. When the voltage is first applied, excessive current will flow. For limiting this current, since there will be no resisting back electromotive force (emf),some series resistance can be added to the armature windings.

Product

Digital Igniter Tester

Alpha 4314KRC

-

Valhalla Scientific Inc.

Alpha 4314KRC - Valhalla Scientific Inc.

The Alpha 4314 Digital Igniter Tester is a portable digital ohmmeter which has been specifically designed for ultra-safe resistance testing on explosive devices (i.e. squibs, detonators).

Product

Protective Bonding Testers

RMO-E Series

-

IBEKO Power AB

RMO-E Series - IBEKO Power AB

The RMO-E instruments are designed and ideal for testing protective bonding (grounding) of equipment following the standard IEC 61010-1. Also, they can measure the resistance of high, middle and low voltage circuit breakers, high-current bus bar joints, cable splices, and welding joints. The instruments accurately measure not only in factory environments but also in high-induction fields and substations.Both models generate a true DC ripple-free (less than 1 %) current with automatically regulated test ramps. During a test, the protective bonding testers automatically generate increasing current before measuring and decreasing current after the measurement. Consequently, this significantly decreases magnetic transients and ensures great accuracy.These instruments can store up to 500 measurements in the internal memory and have a built-in thermal printer available as an option.DV Win software communicates with the RMO-E earth resistance meter via USB or RS232 interface. It allows a user to run the test remotely from PC, as well as to download test results, analyze and generate fully configurable test reports.The RMO-E series contains two models, RMO60E and RMO100E. The main difference between these two models is in the maximal test current:60 A DC for RMO60E100 A DC for RMO100E

Product

Low Resistance Ohm Meter

6237 DLRO

-

Standard Electric Works Co., Ltd

6237 DLRO - Standard Electric Works Co., Ltd

The 6237 DLRO is a "full feature professional instrument". The RUGGED and "O-RING" SEALED Digital LowResistance Ohm and Contact Meter is specially designed to measure very low resistance accurately and give the result directly on the large and clear LCD. The 6237 DLRO makes measurements by passing a constant current through the device under test (generally a conductor, contact or low resistance) and measuring the voltage across it. The Low Resistance is then calculated by ohm's law. This superb instrument is powered by rechargeable battery. It is supplied complete with instruction manual. This ensure that every product is not just fully functional and calibrated after the assembly lines, but also within tight specifications tolerances before leaving the strict quality control of Standard Electric Works.

Product

500 MHz Passive Probe for HDO4000, 10:1, 10 MOhm

PP018-1

-

Teledyne LeCroy

PP018-1 - Teledyne LeCroy

Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.Each passive probe is recommended for a certain oscilloscope, using the right passive probe with the right oscilloscope means that the probe will be properly compensated across the entire bandwidth. Using probes with a different oscilloscope will only let you compensate for low frequencies.

Product

DC Electronic Load Control Software

EES-100-xx

-

Executive Engineering

EES-100-xx - Executive Engineering

EES-100  Software controls all electronic load types.  ( Single & Dual channel) data logging, constant current, constant voltage, constant power, constant resistance, up-down timing, V/I Curves, Graphing, Response Testing

Product

ICI Mace Snag Tester

UI-TX07

-

Unuo Instruments

UI-TX07 - Unuo Instruments

ICI Mace Snag Tester – ICI Mace Tester is used to test fabric snagging resistance ability. It is suitable for woven and hnitted fabric made from textured or untextured filament yarns and etc. ICI Mace Snag Test Method includes ASTM D3939, JIS L1058, GB/T 11047 and etc.

Product

Insulation & Multifunction Tester (LCD Display)

4153 IN

-

Standard Electric Works Co., Ltd

4153 IN - Standard Electric Works Co., Ltd

Microprocessor-controlled. Measures Insulation Resistance, voltage (AC-DC) measurements with automatic hold facility, diode, ohm, and continuity with a short circuit current of minimum 220mA. Auto-off function. Energy conservation feature. Ener-Save™ limit the test duration to about 10 Seconds. Quick Test and EnerSave™ are unique features. Both saves energy. No moving parts. All calibration are saved internally in a non volatile memory. Easy calibration at any facility around the world. Operates with rechargeable batteries, alkaline or low cost general purpose batteries. Low cost maintenance, calibration, and ownership. Complies to all the latest regulations, including UK.

Product

Ground Grid Tester

GGT Series

-

IBEKO Power AB

GGT Series - IBEKO Power AB

The GGT500 ground grid integrity tester is designed for inspection of the substation ground grid. It can also be used as a portable micro-ohmmeter with Both Sides Grounded and Remote Control functionalities. It is intended to inspection the conditions of a grounding system beneath substations, testing of medium- and high-voltage circuit breakers, disconnecting switches, high-current bus bar joints, cable splices, and different high-current links.In the United States when inspecting the quality of the grounding systems beneath a substation, the proper procedure is to inject 300 A DC during a time period of 60 s. This is what the GGT500 will do, and in that time period, the current path and voltage drop are checked. Also acting as a micro-ohmmeter, the GGT500 can test low resistance values by producing high test currents of up to 500 A.The instrument is placed in an unbreakable, plastic case with IP67 protective rating (with closed lid). Although very portable and lightweight, micro-ohmmeters have very high output power capabilities. High output voltage enables a wider measurement range at higher test currents, as well as the use of thinner/longer test cables. GGT500 ground grid integrity tester generates a true DC ripple-free (less than 1 % ripple) current with automatically regulated test ramps. This significantly decreases magnetic transients and ensures great accuracy.When used for testing in Both Sides Grounded conditions, a special current clamp powered from the ground grid integrity tester is used for measuring a current through groundings. If even a higher safety level is required, the remote control feature enables the operator to perform measurements from a distant location, away from the instrument and test object.

Product

Variable Resistors/Potentiometers

-

CTS Valpey Corp.

CTS Valpey Corp.

When a design calls for a variable resistance, CTS can supply a solution in the form of a wide variety of rotary and slide-action variable resistors / potentiometers.

Product

Shore Hardness Testers

-

NovoTest

NovoTest

Measures the level of resistance a material demonstrates against indentation pressure.

Product

Box Compression Tester

BCT-03

-

Jinan Leading Instruments Co., Ltd.

BCT-03 - Jinan Leading Instruments Co., Ltd.

BCT-03 Box Compression Tester is professionallyused to test the compression resistance property of carton box, corrugated box,honeycomb cardboard box and other packaging. And it’s also applicable tocontainer compression test of  plasticbucket (edible oil, mineral water), fiber drum, carton, paper, cans, containerbarrels (IBC barrels).