-
Product
High Speed Device & Flash Programmer
JT 2147 QuadPOD
-
The JT 2147 QuadPOD high speed device programmer and flash programmer comprises JT 2148 transceiver and four independent, programmable JT 2149 TAP PODs and provides signal conditioning for the DataBlaster series of boundary-scan controllers. Used for gang, parallel, fast testing / Programming of devices.TAP pods can be housed integrally within the transceiver or they can be detached and reconnected via the (optional) one meter extension cable. The JT 2148 transceiver is available in standard (/10) or industrial (/13) variants. The /13 variant includes a SCSI cable splitter to allow system integrators to use flat ribbon cables into the transceiver itself which often simplifies fixture building.A fixture-embedded variant of the JT 2147 is available as part reference JT 2147/FXT. This unit integrates the function of the transceiver and four pod onto a single assembly. This variant can also support 64 DIOS channels and SCIL functions (see more images below for a picture of the JT 2147/FXT).
-
Product
Portable Hydraulic Testers
-
Flo-tech portable hydraulic testers simultaneously measure the flow rate, temperature and pressure of hydraulic fluid. Flow rates are derived from an internal turbine meter assembly. These units were designed for testing pumps, valves, cylinders, motors, hydrostatic or power shift transmissions and power steering systems in both mobile and stationary applications. When used in a preventive maintenance program, untimely or catastrophic repairs are minimized. Three families of testers are available to provide operators with the perfect solution that fits their needs, each quipped with a carrying handle to improve portability.
-
Product
Altitude Encoder Calibration Programmer
ECP-100
-
The ECP-100 allows the avionics technician to assign serial port protocols, 100' or 10' resolution and/or allow programming of the calibration curve on Trans-Cal Altitude Encoders using the RS232 port.
-
Product
Breadboard Module for 34980A
34959A
Breadboard Module
The Keysight 34959A module for the 34980A Multifunction Switch/Measure Unit can be used to create custom designs inside the Mainframe. You can control your circuits with access to both the +12V and +5V supplies, 16 GPIO ports, and 32 relay drive lines. The faceplate has cutouts for the most common connectors. The breadboard module can be programmed using standard read and write commands in SCPI.
-
Product
PXI Vehicle Multiprotocol Interface Module
Interface
PXI Vehicle Multiprotocol Interface Modules use hardware-selectable NI-XNET Transceiver Cables (TRC) to communicate High-Speed/Flexible Data‑rate CAN, Low-Speed/Fault Tolerant CAN, and/or LIN. Using the NI-XNET driver, you can create applications that require real-time, high-speed manipulation of hundreds of CAN and/or LIN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time. PXI Vehicle Multiprotocol Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
Product
Power PC 8641D Based Board
MS 2501
-
Ethernet Port:4 Channel (1GBPS)CAN Port:1 ChannelMIL1553B:1 Channel (Dual redundancy)RS232:4 Channels (512 byte FIFO, 4MBPS)RS422:12 Channels (512 byte FIFO, 4MBPS)JTAG:Flash Programming and Debugging
-
Product
Advanced Driver Assistance System (ADAS)
-
Cars have come a long way since they first came on the road in the 19th century. The first semiconductor-based noteworthy assistance was GPS-based car navigation systems toward the end of ´80s. Today, in almost every car, ABS (Anti-Lock Braking System) and ESP (Electronic Stability Program) are also contributing toward the driver and car passenger’s safety using high quality electronics. After all, the dreams of automated cars from the ´60s are now becoming true — it is only a matter of a few years.
-
Product
Optical Measurement
-
• Vertical optical measuring machine for static and dynamic measurement of various elements on small cylindrical parts.• The parts can be mounted between two centres or held in place using various accessories.• Attractive design and robust construction with many new features: New touch screen control panel for easy operation directly at the workplace, bi-telecentric optical system, high resolution CMOS camera, precision sliding headstock with integrated and protected daily standard, quick and easy accessory changing system, integrated temperature sensors, dynamic LED indicator of the general status of the measured part (GO/NG) and operator messages. Equipped with an exclusive optics tilting system.• Machines specially designed to measure threads such as, parallel, trapezoidal, conical, round, square, conical, worms, ball screws, bone screws, dental implants, etc.• Reflex SCAN+ concept for measuring parts without prior programming at the touch of a button• Delivered complete with a PC and the Reflex SCAN+ software, which allows a multitude of elements to be measured easily and intuitively.
-
Product
Stator Testing System for EV Motor
EVT531
-
Shanghai Dean Electrical Co., Ltd
To meet the standard test projects requirement of the international companiesTo control and analysis the programs will reduce the human careless and misjudgmentEasy to edit environment and easy to learnIt can test multiple sets of DUTs simultaneouslyWhen there are several DUTs are tested, it could identify the undesirable sets individuallyThe Impulse/Surge with waveform comparison is a non-destructive analysisPolarity testMaximum saved files will be up to 100 setsIt provides the password functionSpeeding test could save time and improve efficiencyChinese and English pages can be arbitrarily switched
-
Product
Universal Device Gang Programmer
SUPERPRO/7504N
-
eMMC programming speed 10 times higher than SuperPro/5000, Universal package adaptors thanks for 144pin universal Pin-drivers, Engineering and production programmer in one unit. Gang4 adaptors available, Max support 16pcs IC in one time.
-
Product
Hazardous Location Syringe Pump
500HLf
-
The Teledyne LABS HLf-Series pumps give you the same accurate, predictable flow and pressure control as our standard D-Series, while conforming to safety standards for use in UL Class I, Division 2, Groups A B C & D, T4 environments. The hazardous location rating is achieved through internal design modifications including the use of brushless DC motors. This approach eliminates the need for purge boxes or other additional safety devices. Wetted materials are compatible with most aqueous and organic liquids, corrosive solutions, heated fluids, liquefied gases, viscous fluids, or slurries and pastes. If needed, optional materials such as Hastelloy C-276 are available on request. The HLf controller has a keypad and LCD, as well as built-in and optional interfaces for computer control and other devices. Programming is easy and flexible, with instant access to menu screens even when the pump is running. This allows you to change operating parameters on the fly.
-
Product
Fire, Gas & Intruder Controllers & Alarms
MultiSafe-MX
-
Teledyne Gas & Flame Detection
The MultiSafe-MX system is intended for the protection of high hazard, high risk plant and facilities.The MultiSafe-MX is certified, by European laboratories, to comply with the applicable regulations.The panel is composed of dedicated cards, installed in 19” racks which have their own “intelligence”, programmed for active/passive fire protection, gas detection, intruder alarm and logic functions. Moreover, the MultiSafe-MX can interact with supervisory and SCADA systems via Ethernet, TCP/IP or Modbus.The MultiSafe-MX interfaces with devices using either conventional and/or addressable module inputs and outputs. These modules are used to tailor the system to customer requirements.
-
Product
Display
XYZ Oscillograph
-
XYZ Oscillograph is a program assessing signal forms and displaying signal parametric dependence.
-
Product
MCB Thermal Trip Calibration Test Bench (IEC 60898 Cl 9.10.1.2, Annex I.1, IS)
-
The test system is designed and customized to carry out 2.55*Intest as per Table 7 (test c) of IEC 60898 (also mentioned for routine testing of MCBs. The test is done at dc current to exactly analyze and correct the bimetallic properties of the MCB as far as thermal tripping is concerned. The unit comes with a pneumatically operated test fixture with in-built dc stepper motor that is controlled by a micro controller / PC to calibrate the breaker into a narrow tripping band programmed by the user.
-
Product
Software
-
The Circuit Sleuth API Tool Kit routines offer an alternative solution for users who prefer writing or need to write their own control programs, or have specific application needs for frequency response analysis. The “C” callable routines and DLLs provide direct access to the analyzer, enabling the user to control instrument functions and data management.
-
Product
Power Analysis Software
PAS
-
PAS is SATEC's comprehensive analysis and engineering software designed to program and monitor all SATEC devices. It includes a variety of additional tools to assist in system setup, such as the communication debugging module.
-
Product
Load Support Unit
LSU220A
-
The LSU220A is a general purpose load support unit designed to act as a permanent power supply to maintain backup battery systems whilst alternative sources of power are either impractical or unavailable, such as running diesel engines during maintenance programs.
-
Product
TPMS Tool
TPA 300
-
The Bosch TPA 300 is a comprehensive TPMS tool designed for sensor programming, activation and ECU reset. The full-color, intuitive interface guides the user when replacing and servicing TPMS sensors. When paired with a compatible Bosch diagnostic scan tool, like ADS 325 or 625, users can reset the ECU in less than two minutes. The TPA 300 supports all known OE and aftermarket programmable sensors for all light vehicles. Frequent updates allow new features, vehicles and sensor coverage to be added regularly.
-
Product
High Speed Pick and Place Handler
Commander 2000
-
At throughput rates in excess of 2000 Units per Hour the HT Commander 2000 system provides unparalleled performance for the production handling and programming of flash memory devices or modules.
-
Product
PBM-3G
PBM-317-3G-V2
-
PBM-317-3G-V2, 17″ Portable & Rack-mountable monitor enhanced V2 series consists of high quality portable LCD panel, specifically designed for multiple video server inputs program & preview monitoring, camera output & return feed side by side and multiple camera preview wall monitoring. PBM-3G series designed for every possible broadcast mobile environment ensuring accurate color reproduction in accordance with SMPTE, EBU, REC 709 Broadcast Standards.
-
Product
LED Inspection
-
Indicates which LEDs are not working. Checks if all diodes are placed in the correct places. Independently configures a test program for each new LED panel. Fast and effective – 1000 LED panel test takes up to 3 seconds.
-
Product
Task Sequencing and Automated Process Control
T-Zero
-
Command and Control Technologies Inc.
T-Zero is a unique process control program that facilitates automated design and execution of command, control, test, and monitoring activities. It features visualization of the operations process itself coupled with automated coordination of group activities. The software provides a visual, role-based interactive timeline built on the real-time data processing power of the Command and Control Toolkit™ (CCTK). T-Zero is the perfect automation solution for labor -intensive procedural activities: improving process organization, repeatability, and freeing operations staff from tedious task details to focus on strategic operational objectives.
-
Product
PLC engineering software
GX Works3
-
Mitsubishi Electric US, Inc., Industrial Automation Division
GX Works3 is the latest generation of programming and maintenance software offered by Mitsubishi Electric, specifically designed for the MELSEC iQ-R and MELSEC iQ-F Series control system. This intuitive engineering software encompasses the complete product development cycle, simplifying complex programming tasks through a graphic-based configuration. It supports structured programming in compliance with IEC 61131-3, enhancing project standardization. With features such as integrated motion-control system configuration and multi-language support, GX Works3 ensures a comprehensive, trouble-free engineering environment solution, significantly reducing development costs and streamlining the maintenance process.
-
Product
PCI-8361, PCI Host, 100 MB/s, Copper Cable MXI-Express Device for PXI Remote Control
781394-01
Remote Control
The PCI‑8361 is an MXI‑Express remote controller for devices or systems over cabled PCI from a computer with a PCI slot. The PCI‑8361 card provides a PCI link over a copper cable to the PXI‑8360 remote control module when used for PXI system control. This link is transparent to software applications and drivers, so computers and servers can control connected devices with no additional programming. With NI remote controllers, PXI modules can be used as if they are PCI devices directly installed in the computer.
-
Product
6TL10 Table Top Test Base
H71001000
Test Platform
The 6TL-08 base platform was designed to cover the most common testing and in-system programming (ISP) needs with a reduced initial budget. The system includes a robust manual linear push mechanism allowing a low-cost fixture strategy thanks to the exchangeable cassettes.The platform enclosure features an 8-Slot fixture receiver, compatible with VPC 90 Series Mass Interconnect Module, as well as 6TL intelligent YAVModules (YAV90MMU &YAV90059), with room for fast ISP devices, optional PXI chassis and various power supplies. A removable back panel allows easy placement of custom connectors or test auxiliary circuitry.
-
Product
Audio Volume Meter
AVM
-
This is a true RMS audio storage meter used to measure audio volume levels of live program material. Use it to periodically survey your system for high or low audio levels to prevent complaints about loud or un-even audio programming. You can use this meter to quickly locate and verify any objectionable signals levels and bring them into compliance.
-
Product
NI-9401, 5 V/TTL, 8 Bidirectional Channels, 100 ns C Series Digital Module
779351-01
Digital Module
5 V/TTL, 8 Bidirectional Channels, 100 ns C Series Digital Module - The NI‑9401 is a configurable digital I/O interface for input or output in 4‑bit increments. Therefore, the NI‑9401 can create three configurations: 8 digital inputs, 8 digital outputs, or four digital inputs and four digital outputs. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the NI‑9401 for implementing custom, high-speed counter/timers; digital communication protocols; pulse generation; and more. Each channel features transient isolation between the I/O channels and the backplane.
-
Product
160W DC Programable Power Supply
-
*Source effect: CV≤0.01%+3mV(mA)*Load effect: CV≤0.01%+3mV(I≤3A) CC≤0.2%+3mA(I≤3A) CV≤0.02%+5mV(I>3A) CC≤0.2%+5mA(I>3A)*Ripple and noise: CV≤1.0mVrms(I≤3A) CC≤3mArms(I≤3A) CV≤2.0mVrms(I>3A) CC≤6mArms(I>3A) *Protection Type: Overcurrent Protection (OCP) Overvoltage Protection (OVP)* Display accuracy: Voltage indication accuracy: ± (0.5% + 2 words)
-
Product
ElcoMaster Oven Profiling Software
-
*Oven Logger set up & programming*Paint/Powder parameter library*Product probe maps*Fully customisable inspection templates*Selectable probe/channel traces*Statistical analysis by probe/channel*Max, Min, standard deviation, coefficient of variation*Temperature profile, cure progress, histogram & individual cure value graphs against product*Time at temperature, time of peak difference*Time above maximum absolute & minimum cross link temperatures*Fully customisable inspection reports*Combined reports - coating thickness, gloss, adhesion, profile, climate, surface cleanliness*Report generator wizard & PDF generator*Email or export data*Import photo’s, data sheets, critical data, inspection notes, etc & include on inspection reports*Cloud computing - allows for cross site collaboration, including internal text messaging tool*Overlay temperature profiles, review and compare multiple oven profiles over time*Use additional data loggers for multiple channels or run overlays





























