-
Product
FPGA Testing
-
Silicon Turnkey Solution, Inc.
The secret to our success in the FPGA testing field is the STS hammer file, a proprietary test methodology based on our experience testing thousands of unique FPGA designs. The hammer file is designed to program the FPGA to its maximum combination and block configuration and then tests the completely programmed FPGA for full dynamic, DC and at-speed AC performance. Power and transient tests are also conducted under worst-case populated configurations. Application-specific usage configurations are also used to assist in generating the worst-case electrical specification limits at worst-case environmental use.
-
Product
High Speed Leak Tester
F28+
-
Elevates the leak test to a whole new level of speed, flexibility and accuracy. Differential pressure decay leak measurement: vacuum to 20 bar. Multi-test leak tester. 128 programs. Integrated fill and dump valves. Optional auto fill: Vaccum – 500 mbar – 5 bar – 9 bar (inside the module).
-
Product
Serial to Relay Minibox™
Model 2364
-
* Model 2364-11 provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully IEEE-488.2 and SCPI compliant.* Optional 1 'U' high Rack Mounting Kits hold one or two 2364s.* Includes 50-pin mating connector for solder connections.* Optional 1 'U' high Rack Mounting Kits hold one or two 2364s.* Optional 115750 Terminal Board and Terminal Strip for easy connections without soldering. See the Serial Accessory page.
-
Product
cRIO-9042, 1.60 GHz Quad-Core CPU, 4 GB DRAM, 4 GB Storage, -40 °C to 70 °C, Kintex-7 70T FPGA, 4-Slot CompactRIO Controller
785622-01
Controller
1.60 GHz Quad-Core CPU, 4 GB DRAM, 4 GB Storage, -40 °C to 70 °C, Kintex-7 70T FPGA, 4-Slot CompactRIO Controller - The cRIO-9042 is a rugged, high-performance, customizable embedded controller that offers Intel Atom quad-core processing, NI-DAQmx support, and an SD card slot for data-logging, embedded monitoring, and control. It includes a Kintex-7 70T FPGA with LabVIEW FPGA Module support for advanced control and coprocessing. The controller provides precise, synchronized timing and deterministic communications using Time Sensitive Networking (TSN), which is ideal for highly distributed measurements. This controller offers several connectivity ports, including Gigabit Ethernet, USB 3.1, USB 2.0, RS232, and RS485 ports. You can use the USB 3.1 ports to add a local human machine interface and program, deploy, and debug software, which simplifies application development.
-
Product
8-in-1 Transcoder
SFT3248
-
Hangzhou Softel Optic Co., Ltd.
SFT3248 is a professional bidirectional trans-coder to convert video between H.264 and MPEG-2 format and also to trans-code between HD and SD programs simultaneously. It is equipped with 6 tuner inputs to receive channels directly from satellite, or ASI /IP inputs to receive digital channels. After trans-coding, it outputs MPTS & SPTS through the DATA port or ASI port.
-
Product
Horizontal Thermal Shock Test Chamber (2 Zone)
-
Guangdong Test EQ Equipment co., Ltd.
- Integral structure,the internal overall TIG seamless welding, beautiful appearance; Door lock device adopts lever power opening mechanism.- The use of Chinese color LCD touch man-machine interface + high-performance programmable controller (PLC), with TESTEQ test box independently developed special software, with automatic, intelligent, human control and other characteristics.- TESTEQ patent "Cold and heat balance technology",low temperature constant temperature season can be more than 30%.- Control mode: constant operation mode, program operation mode.- Refrigeration compressor and key accessories are selected international and domestic well-known brands, long-term and reliable operation; Environmentally friendly refrigerant, in line with the requirements of international environmental protection conventions.
-
Product
Advanced Projector Controller
HR-3P
-
The Model HR-3P is a serial control device that can automatically detect video on one of its 3 video inputs and issue commands to the projector (e.g. turn on, select input, etc). The video inputs are VGA from a PC or a Notebook and 2 TV-signals (Composite Video and S-Video) from VCR, DVD, Satellite Receiver, or Video Cameras. The HR-3P provides pass-through video for the S-Video and Composite Video and has a 1 in x 2 out video splitter for the VGA. The unit features a bi-directional RS-232 serial port that can be used for programming command strings for your specific projector and later connected to the projector for control and normal operation. The HR-3P is an ideal tool for the automation of a projector in a presentation setup.
-
Product
Potentiostat/Galvinostat
EZstat Pro
-
The EZstat Pro potentiostat/galvanostat uses a versatile menu-driven waveform generator (periodic or aperiodic) with preset battery cycling, Tafel plots, and cyclic voltammetry procedures.Users can program sequences of steps blending current and potential control with a resolution of 8 uS/point. EZstat Pro can perform electrochemical impedance spectroscopy (EIS) and uses active IR compensation. The instrument can interface with the EZpump peristaltic pump for flow batteries and fuel cells.
-
Product
Connection to the PC
ADwin Driver
-
For the implementation of graphical user interfaces on the PC multiple programming languages and development environments are available. ADwin provides ready-to-use drivers based on DLL or ActiveX technology which can be easily integrated into your programming environment. With our ADwin drivers, you obtain direct access to communication and data exchange with your ADwin system.
-
Product
BenchLink Waveform Builder Pro Software
33503B
-
BenchLink Waveform Builder Pro software eliminates the need for tedious programming and makes custom waveforms fast and easy.
-
Product
Military-Grade 4-In-One Temp/Humidity/Vibration/Pressure Test Chamber
-
Guangdong Test EQ Equipment co., Ltd.
- Integral structure, the internal overall TIG seamless welding, beautiful appearance; Door lock device adopts lever power opening mechanism. - The use of Chinese color LCD touch man-machine interface + high-performance programmable controller (PLC), with TESTEQ test box independently developed special software, with automatic, intelligent, human control and other characteristics. - Control mode: constant operation mode, program operation mode. - TEST EQ patent "Cold and heat balance technology”, low temperature constant temperature season can be more than 30%. - Refrigeration compressor and key accessories are selected international and domestic well-known brands, long-term and reliable operation; Environmentally friendly refrigerant, in line with the requirements of international environmental protection conventions. - The humidification system adopts TEST EQ patented technology. - The lift structure through the lift (wireless remote control) up and down and left and right movement to match the shaking table horizontal or vertical table, comprehensive performance test. - Gantry structure: Through worm gear (wireless remote control), the studio box is lifted up and down and the gantry is moved around to match the horizontal or vertical table of the shaking table, and the comprehensive performance is tested. - The seal of temperature and humidity box and vibration table adopts TESTEQ patent technology low pressure flexible connection device. - Pressure mode: internal pressure type or external pressure type. - Vacuum system: the world famous brand ""Laibao"" or ""Jitis"". - Configure RJ45 communication interface, remote control system (open data transmission protocol support Modbus/OPC). - Surface electrostatic powder spraying; chamber color ""TESTEQ White "", controller panel color ""TESTEQ Blue "".- TESTEQ patent cold well adsorption anti-condensation function (optional).
-
Product
Wireless In-Circuit Test Fixtures
-
Higher density more complex circuit boards complicate testing requirements while smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in standard long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board or T-Board®. Circuit Check’s wireless fixture technologies reduce test program debug and maintenance times while easing the ECO process. Thus allowing for the higher level of test performance, the ability to probe smaller denser targets and achieve ultra-high node counts.
-
Product
NI-9237, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
779521-01
Strain/Bridge Input Module
50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The NI‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the NI‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools.
-
Product
High-Performance Autoranging DC Power Module, 50V, 10A, 100W
N6752A
Power Module
The Keysight N6752A is a 100 W high-performance, autoranging DC power module that provides low noise, high accuracy and programming speeds that are up to 10 to 50 times faster than other programmable power supplies. Optional high-speed test extension offers an oscilloscope-like digitizer that increases measurement accuracy when viewing high-speed transient or pulse events within the device-under-test (DUT).
-
Product
Logic Analyzer
Ant18e
-
The Ant18e logic analyzer is compact, easy to use, powerful, and inexpensive. The Ant18e features high speed data acquisition, state (synchronous) and timing (asynchronous) acquisition modes, Trigger-In and Trigger-Out connections, and a user-level programming interface.
-
Product
Digital I/O Card w/CoS IRQ
mPCIe-DIO-24S
-
The mPCIe-DIO-24S is a type F1 PCI Express Mini Card (mPCIe) and optional cable assembly (D-Sub 37-pin Male connector) designed to be easily panel-mounted in any application environment. It uses the high speed PCI Express bus to transfer digital data to and from the card. The digital I/O is compatible with 8255 PPI chips making it easy to program.
-
Product
USB-COM Data Logger
-
The USB-COM Utility is a free data logging andconfiguration program for use with the Validyneseries of USB or Serial pressure transducers.USB-COM Utility also comes in a premiumversion that allows up to eight signals to begraphed simultaneously while being recorded toa .csv file. The graph X and Y axis may bescaled to any values set by the user. A separatehistorical graph provides a complete visualrecord of the signals from the start of logging.
-
Product
pH/DO/Conductometer
867/856 Modules
-
With the 856 Conductivity Module and 867 pH Module, you can build your own, customized solution – whether you are analyzing large sample loads or multiple parameters, or you want to enjoy full freedom when it comes to method programming and applications.
-
Product
Data Collection And Analysis Software
-
The MESUR™ software series expands the functionality of Mark-10 force and torque gauges, indicators, testers, and test stands. MESUR™ Lite is a basic data acquisition program included free with all Mark-10 products, while MESUR™gauge is a more advanced software package which also plots, calculates statistics, generates reports, and provides other analysis tools. MESUR™gauge Plus adds motion control of certain test stand models.
-
Product
Benchtop AOI Machine
Sherlock-300F
-
Many companies, especially smaller electronics manufacturers, put off adding automated optical inspection (AOI) to their process because of the high capital investment, the sharp learning curve, and the need for an experienced operator to program and fine-tune it. Benchtop Sherlock 300F AOI machine was designed to make in-house AOI affordable and manageable for first-article inspection, prototyping, and even full production inspection requirements. It features the same technology and quality build of the batch and inline Sherlock 300 models—plus the same two full days of installation and training at your facility offered with the other models*—in a smaller size, at a lower price point.
-
-
Product
M3 and em4 softwares
-
The M3 and em4 softwares are easy to program, powerful, and user-friendly thanks to a strong experience in programming software development
-
Product
The Language of Technical Computing
MATLAB
-
MATLAB is a high-level language and interactive environment for numerical computation, visualization, and programming. Using MATLAB, you can analyze data, develop algorithms, and create models and applications. The language, tools, and built-in math functions enable you to explore multiple approaches and reach a solution faster than with spreadsheets or traditional programming languages, such as C/C++ or Java. You can use MATLAB for a range of applications, including signal processing and communications, image and video processing, control systems, test and measurement, computational finance, and computational biology. More than a million engineers and scientists in industry and academia use MATLAB, the language of technical computing.
-
Product
Econo Motion Controllers
DMC-41x3
-
The DMC-41x3 motion controller is one of Galil's latest generation, stand-alone motion controller. Compared with the DMC-21x3 controller, the DMC-41x3 offers the following enhancements: 100BASE-T Ethernet, aux RS232 port, USB port, uncommitted analog inputs, up to 15 MHz encoder frequencies, more program memory, and faster sample frequencies. The DMC-41x3 also accommodates the same stepper and servo motor drives used in the DMC-40x0 series and allows two 4-axis 750 W drives to be installed in the 8-axis controller package. The DMC-41x3 is available as a box-level or card-level motion controller. The unit operates stand-alone or interfaces to a PC with Ethernet 10/100BASE-T, or USB. It includes optically isolated I/O in addition to analog inputs and outputs. The DMC-41x3 controller and drive unit accepts power from a single 20-80 VDC source.
-
Product
Programmable Boards
LEO Board
-
LEO Board is a free programmable Aid for students who want to practice and enlarge their knowledge in programming of microcontrollers.
-
Product
Drop-In Functional Test Fixtures
-
Circuit Check’s drop-in base fixture and replaceable personalized plates are the ideal solution where production volumes are lower and the need to change from one fixture and test program to another occurs quickly. Interchangeable test fixture drop-ins enable the same test system to be quickly reconfigured with different tooling and probe patterns for different products. This maximizes equipment re-use, while minimizing the cost for each new test. With Circuit Check’s base fixture and drop-ins, the wiring and test electronics are not disturbed, thus ensuring configuration consistency each time the system is re-tooled.
-
Product
x1149 Boundary Scan Analyzer
N1125A
-
The x1149 is a tool for engineers to perform structural test such as opens and shorts tests on their PCBAs. It also performs In-System Programming for devices such as FPGAs and CPLDs.
-
Product
Loss of Video Detectors
-
Program video and audio (balanced or unbalanced) is routed through the SG-8. With program video present at the input to the SG-8, the video and audio outputs of the SG-8 are the program signals. Upon loss of the video portion of the program input, the SG-8 defaults to internal SMPTE Color Bars and 1 kHz tone.
-
Product
Automated Programmers
-
The time required to process a typical production order through the factory is generally reduced with automation. Xeltek offers mid to high volume automated programming solutions at a highly competitive price. With the automated SuperBOT systems installed, less manpower is needed for operation, thus lowering operational cost tremendously. Less manhandling of production line also reduces human induced errors and failures, resulting in higher reliability.
-
Product
RF Upconverters
-
SignalCore offers traditional multi-stage and single-stage RF upconverters, and Direct IQ modulators that feature low phase noise, high dynamic range, wide bandwidth, and continuous tuning. SignalCore RF upconverters are compact and built for mechanical robustness and ruggedness. Applications include various test and measurement applications such as those in point-to-point radio, wireless communication, ATE, and software-defined radio. All products are provided with a Graphical User Interface (GUI), driver, and API for easy programming control.
