Remote Terminal Unit
Collects data from data acquisition (DAQ) devices and transmits the information to the main test system via a network.
-
product
PXI/PXIe Microwave Multiplexer, Single SP6T, 50 GHz, 50 Ω, SMA-2.4, Terminated, Remote Mount, Failsafe
42-785C-551-TE
The 40-785C-551-TE (PXI) and 42-785C-551-TE (PXIe) are single failsafe SP6T 50 GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
product
PXI/PXIe Microwave Relay, Dual SPDT, 26.5 GHz, 50 Ω, SMA, Internal Termination, Failsafe, Remote Mount
40-781A-222-E
The 40-781A-222-E (PXI) and 42-781A-222-E (PXIe) are dual failsafe SPDT 26.5 GHz microwave relay modules with internal terminations and remotely mounted relays. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50 GHz in 50 Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
product
Remote High Performance Receiver
E1709A
The measurement signal frequency changes as the stage velocity changes. The Keysight E1709A ensures minimal phase processing errors due to frequency changes. The receiver also provides immunity to errors induced by changes in measurement signal power that occur due to small pitch, roll and yaw movements during stage motion. These features help provide the most accurate measurements under system motion.
-
product
FREQUENCY DISPLAY UNIT
TYPE NFD-1
The National RF Type NFD-1 Frequency Display Unit was designed for use with vintage and classic communications equipment, to display the received or transmitted radio frequency. The unit incorporates an internal processor that allows the intermediate frequency (IF) to be counted out by the frequency counter. The resultant display is the actual frequency that the equipment is receiving or operating at.
-
-
product
PXI/PXIe Microwave Multiplexer, Dual SP8T, 40 GHz, 50 Ω, SMA, Terminated, Remote Mount
40-788-052-TE
The 40-788-052-TE (PXI) and 42-788-052-TE (PXIe) are single SP8T 40 GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays.
-
product
PXI/PXIe Microwave Multiplexer, Dual SP4T, 26.5 GHz, 50 Ω, SMA, Terminated, Remote Mount, Failsafe
42-785C-432-TE
The 40-785C-432-TE (PXI) and 42-785C-432-TE (PXIe) are dual failsafe SP4T 26.5 GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
product
PXI/PXIe 1000Base-T1 Fault Insertion Switch, 3-Channel
40-203-001
The 40-203-001 (PXI) and 42-203-001 (PXIe) are designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They support 3 channels of two wire serial interfaces. Each channel pair can simulate an open fault in either or both wires, and using the fault bus switches can simulate short between both wires or a short to one of two externally applied fault connections – such as battery supply or ground - via two fault buses.
-
product
AC Voltage Proving Units
HLV-1
Standard Electric Works Co., Ltd
● Designed to proof. AC voltage detectors AC voltage testers● Compact, handheld, and easy to carry and use.● Battery operated.● LED indicates when power is "ON".● Normal 4mm test leads.
-
product
16-Channel Bridge Signal Conditioning Unit
ProDAQ 6716
16-Channel Bridge Signal Conditioning Unit
-
product
PXI/PXIe Microwave Multiplexer, Single SP8T, 26.5 GHz, 50 Ω, SMA, Terminated, Remote Mount, Failsafe
42-788-041-TE
The 40-788-041-TE (PXI) and 42-788-041-TE (PXIe) are single failsafe SP8T 26.5 GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-788 range of multiplexers are also available as single or dual, SP8T, SP10T or SP12T panel mounted multiplexers with relays mounted on the front panel.
-
product
PXI Chassis and Remote Controller
Our PXI remote controllers offer a seamless connection between a PC's PCI or PCI Express interface and a PXI chassis.
-
product
Terminators
Excalibur provides a variety of terminators from known manufacturers, such as, Milestek and Trompeter.
-
product
HMI Touch Screen Terminals
Panasonic Industrial Devices Sales Company of America
Panasonic HMI Touch Screen Terminals are among the brightest, sharpest and most flexible Operator Panels in the industry. Building custom interfaces has never been so easy or rewarding.Utilizing Panasonic's built-in tools like a time-saving 3D parts library allows quick and painless Operator Panel set up. From simple LED Displays to 12.1” 32,768 color touch screens, Panasonic has the HMI solution for any application.
-
product
AFU 300 Auto Feather Unit
The Autofeather Unit (AFU), is mounted on the engine’s un-pressurized engine compartment, provides torque signal conditioning, automatic propeller feathering and remote engine uptrim command for Take-Off operations, as well as engine output torque indication to the aircraft cockpit during all engine operating conditions.
-
product
Modular Remote Survey Boat
rQPOD
Xylem Analytics brings together a number of leading technological brands including SonTek, HYPACK and YSI to provide the world's most innovative hydrographic and bathymetric survey systems. The rQPOD is a modular system that when attached to a standard size Torrent Board housing both SonTek M9 and S5 RiverSurveyor ADCP systems, transforms into a motorised platform facilitating remote shore operation for easy collection of ADCP data.
-
product
PXI/PXIe 1000Base-T1 Fault Insertion Switch, 6-Channel
40-203-002
The 40-203-002 (PXI) and 42-203-002 (PXIe) are designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They support 6 channels of two wire serial interfaces. Each channel pair can simulate an open fault in either or both wires, and using the fault bus switches can simulate short between both wires or a short to one of two externally applied fault connections – such as battery supply or ground - via two fault buses.
-
product
12-Ch 10A-250VAC RCV Power Distribution Unit
YAVAR438
- Hardware controlled Enable Input- 12 Power relays up to 10A 250VAC/DC and 300W or 2.700VA switching power- 12 10-mOhm shunt resistors.- 6 Switched 2-Pole sense channels- Single phase isolated or 3-Phases non-isolated switching capabilities, to or from the device under test (power or load)- VPC TriPaddle 96 pins connector.- NI LabView & TestStand driver.- .NET, C/C++, VB driver.- Soft Front panel for direct interface.- CAN Control or Ethernet (with Ethernet to CAN Gateway).- Self-test module available.- Form A
-
product
Remote Indicator System
LineTroll R110CQ
The fault indicator use a 2.4GHz ISM band short-range radio to communicate with the collector mounted on the pole. The collector communicates with up to 9 fault indicators. Both the indicators and the collector are powered by long-life lithium batteries for long and maintenance free operation.
-
product
PXI Chassis And Remote Controllers
We offer both PXI & PXIe chassis and controllers that support all of our PXI switching and simulation modules as well as those from third parties. There is a choice of up to 21-slot 3U chassis with options to reduce acoustic noise and modules that can be powered from a DC source.
-
product
LXI WTB Terminator, 100 ohm
60-983-001
The 60-983 is an LXI compatible Wired Trigger Bus Terminator (WTB) designed to be attached to the end of a WTB cable. The LXI WTB uses a transmission line cable to connect LXI devices together that support the WTB capability of the LXI standard. Like all transmissions it needs to be correctly terminated to avoid reflections that could change the signal amplitude along the cable and generate timing jitter or trigger errors. The 60-983 is a simple terminator that can be placed at each end of the WTB chain to correctly terminate the transmission line with minimal reflections.
-
product
Modular Source/Measure Units (SMU)
E5260A + E5270B
Keysight's modular source measure units (SMU) – E5260A and E5270B – combine versatility and advanced features to optimize testing costs. A variety of price-performance points and the framework to add up to 8 plug-in SMU modules enables a customized solution that can expand as your needs change.
-
product
PXI/PXIe Microwave Relay, Single SPDT, 26.5 GHz, 50 Ω, SMA, External Termination, Failsafe, Remote Mount
42-781A-321-E
The 40-781A-321-E (PXI) and 42-781A-321-E (PXIe) are single failsafe SPDT 26.5 GHz microwave relay modules with external terminations and remotely mounted relays. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50 GHz in 50 Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
product
Preterminated OSP Terminals And Drops
Is a factory terminated OSP fiber terminal designed for quick and easy subscriber connections anywhere in the OSP network when used in conjunction with OPTITIP Hardened Fiber Optic Connectors.
-
product
Piezo Actuator Unit Multi Tester
BK2118
You are always improving your technology and we are right there with you. We developed the BK2118 to help you ensure that your piezo actuators are what you expect them to be. With up to 4 vibration sweeps and 2 channels, you can test a variety of characteristics at a speed that matches your product line. The core technology in the BK2118 is the same as our top selling BK2120C, with the same easy interface and the ability to back up your product's performance with saved test data. It also has the option of entering your own feedback so you can easily see how your DUT's perform during testing.
-
product
PXI 4x3 10GHz Matrix with Termination
40-787-518-4X3-T
The 40-787 Microwave BRIC platform is designed to provide a solution for complex RF matrix applications. Using a common mechanical platform the module can be constructed to provide scaleable non-blocking or blocking microwave matrix for frequencies to at least 20GHz.
-
product
Manual Tablet Testing Units
H-Series
The manual lab testers of the H-series in the new LAB.line design combine state-of-the art technology with usability: round shapes, generous radii and smooth surfaces allow for easy and hygienic cleaning.Operation of the embedded touch display is simple and intuitive: you can change a product or view informative test results with just a few clicks.The H series consists of three unit variations with usually 500 N, alternatively 50 N or 1000 N. The H5 version offers to connect an external scale (Sartorius/Mettler). With the H5+ version, you can even perform high-precision measurements with the external thickness gauge module.
-
product
Pulse Heat Unit (Hot Bar Bonder)
*This method is most suitable for reliable soldering and thermo-compression because heating and cooling are done applying the pressure force*Good repeatability of heating temperature and time requires no skilled workers*Partial heating in short time allows to reduce thermal damages*For implement of Pb free
-
product
Source / Measure Units
A Source/Measure Unit, or SMU, is a source and measurement resource for test applications requiring high accuracy, high resolution and measurement flexibility. SMUs are sometimes also referred to as source monitor units. An SMU can precisely force voltage or current and simultaneously measure voltage and/or current.
-
product
Terminal Mechanical Strength Test
The terminal strength test is used to performed to determine whether the design of electrical terminals and their method of attachment can withstand mechanical stresses to which they will be subjected during installation or disassembly in equipment. These stresses must be withstood by the component without sustaining damage which would affect either the integrity of the terminals or the operation of the component part itself. Procedures are established in this method for testing, for example wire-lead terminals, flexible-flat-strip or tab-lead terminals, and rigid-type terminals which are threaded or have other arrangements for attaching conductors. The forces applied during the test consist of direct axial, radial or tension pulls, twist, bending torsion, and the torque exerted by the application of nuts or screws on threaded terminals.
