Optical Loss Test Set
measures the total amount of attenuation in a length of fiber.
-
Product
Mini Fiber Optic, Contact, Receiver, Polymer Optic Fiber
610113170
Fiber Optic Contact (Receiver)
This contact available for purchase as a patchcord only. Choose link below to configure as a patchcord. Primary mating contact 610113171. (May mate with other ITA contacts, as well.)
-
Product
ARINC 818 Tester
Test Platform
iWave 3U VPX High-Speed Video/Data Processing Card is a rugged standalone module in the 3U VPX form factor, aimed for the high-speed data, video processing, and display applications is ideal for military, defense, and aerospace applications requiring an optimal balance of performance and power efficiency. iWave 3U VPX High-Speed Video/Data Processing Card is implemented using Xilinx Kintex-7 device architecture and has I/O interfaces including High speed 16 channels of transceiver interfaces capable of operating up to 6 Gbps data rate, Gigabit Ethernet, RS232, RS422, PCIe interface, Built-in health monitoring circuits, HDMI input, and output interfaces
-
Product
Fully-Automated CTIA-Compliant OTA Test System
TS8991
Test System
The R&S®TS8991 OTA performance test system measures the spatial radiation and sensitivity characteristic as specified by CTIA and 3GPP.The system software provides ready-to-use test templates for OTA measurements and supports all wireless standards.The integrated report function collects all measured test data such as graphics or numeric results, test environments, EUT information and hardware setup in one document.
-
Product
EMI Test System
TS9975
Test System
The R&S®TS9975 is the base system for conducted and radiated EMI measurements. Due to its modular design, it covers a wide range of applications and can be very easily adapted to the measurement task at hand. Any configuration is possible – from conducted measurements and the small precompliance system with a compact test cell to the accredited test system for large equipment under test. Combinations of different applications or incremental expansion are easily possible.
-
Product
Modular Functional Test Platform
LX-OTP2
Test Platform
The OTP² system platform has recently been available in both the PXI and LXI versions. The OTP2 system platform enables the cost-effective and fast implementation of function test systems based on defined modules and function blocks. Thanks to the open system interfaces, customer-specific adjustments can be made at any time without any problems. When considering options for your next generation functional test system, it is important to assess the entire life cycle of the system and the associated costs and efforts. Use OTP² to accelerate development cycles and reduce the development effort for new functional test systems.
-
Product
In-Line Test Fixture for 6TL33/6TL36
AB799/AT799
Test Fixture
Fixture Kit for Platforms featuring receiver Virginia Panel 9025 and external pusher system. Its heavy duty design supports more than 1.000N.nnThe fixture kit includes the Base fixture (probe plate) as well as the Puhsers plate.
-
Product
Open Test Platform for High Performance Automotive Applications
TSVP
Test Platform
The R&S®TSVP family of products is an open test platform from Rohde & Schwarz ideal for high performance automated test equipment (ATE) applications. The chassis contains a mechanical frame, digital backplane, analog backplane, mains switching and filtering, power supply and diagnostic extensions. A highlight is the analog bus for routing measurement signals between different slots without additional external wiring.
-
Product
Photonics Wafer Probing Test System
58635
Test System
The advancement of the photonics device technology continues to enable broader and more demanding applications in the industry.
-
Product
Test Port Cable, 1 Mm
11500J
Test Port Cable
The Keysight 11500J test port connector has a length of 16 cm and a frequency range of DC to 110 GHz. The 11500J integrates with the Keysight N5250A network analyzer and Keysight 8510XF network analyzer systems.
-
Product
Non-Signaling RF Test Platform for Validation & Production
Universal Wireless Tester
Test Platform
Wireless communication standards are increasingly integrated into vehicles as well as smart home and Internet-of-Things applications. They form the basis for connected services, advanced HMIs, and autonomous driving. The combination of constantly evolving standards and the integration of multiple wireless technologies with many RF channels into new product designs means that measurement speed and quality are becoming a priority.
-
Product
Optical Head Interface
N7749C
Optical Power Meter Interface
The N7749C optical head interface can control two or four 8162-C series optical power meter heads. Readout is supported over LAN and USB interfaces with a built-in web-browser GUI and the SCPI command set common to Keysight optical power meters.
-
Product
Universal In-Line Test Platform
Test Platform
UniLine brings 20+ years of test & quality experience to your manufacturing floor and test automation delivers accurate results, without bias. By standardizing test, product quality improves as costs decrease. Equipment becomes understandable and manageable across departments and station support becomes simple.
-
Product
Mini Fiber Optic, Patchcord, ITA, 36", Multimode, 62.5/125, to ST
7-415804506-036
Fiber Optic Patchcord
Mini Fiber Optic, Patchcord, ITA, 36", Multimode, 62.5/125, to ST.
-
Product
Photodiode Burn-in Reliability Test System
58606
Test System
The Chroma 58606 PD/APD Burn-in system is a high density, multifunction and temperature controlled module based system for photo diode burn-in and lifetime test. Each module has up to 256 Source Measurement Unit channels which can source current and measure voltage in various scenarios such as one described below. The system can accommodate 7 modules for a total of 1,792 device channels.
-
Product
Batterie Inspektor
Battery Test Platform
By combining the most diverse hardware and software modules, Batterie Inspektor™ delivers innovative, automated, and digitalized battery testing at every stage of manufacturing. With this flexible test platform, all modules can be adapted to their respective quality requirements. Manufacturing is simplified through a scalable and standardized framework for both new projects and upgrades.
-
Product
Flexible Cable, 3.5 Mm (Test Port) To 3.5 Mm
85131E
test
Achieve phase stability with this 96.5-cm cable when a DUT is connected, with adapter, directly to the test set port
-
Product
ATE Self Test Fixtures
AL663
Test Fixture
AL663 fixtures include all the electronic parts required to perform an effective test platform diagnostic. The AQ818 device allows to perform a series of tests, obtaining a report of the faulty instruments or switch modules and also a report about the relay contacts estimated life.
-
Product
Component Test Systems
Test System
These products include test peripherals used with test systems, such as interfaces that connect semiconductor devices with test systems, and handlers that transport semiconductors to the test system. System-level test equipment and software are also included in this category.
-
Product
2m BNC Test Cable
16048D
Test Port Cable
The 16048D test leads extend the measurement port with a 4-terminal pair configuration. It provides a BNC female connector board to allow attachment of user-fabricated test fixtures.
-
Product
EBIRST 78-pin D-type To 68-pin Male SCSI Adapter
93-006-401
Test Adapter
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
Broadband Optical Source - PXI
SLED 1000 Series
Optical Source
The SLED 1000 Series is a super-luminescent LED light source with high output power, large bandwidth and low spectral ripple. It comes in various wavelength models to address applications in the telecom and datacom markets.The SLED is a single-slot PXIe module and is ideal for building a customized optical testing platform that delivers reliable and repeatable results in manufacturing or R&D environments.
-
Product
1x13 Optical Switch
N7734A
Optical Switch
The N7734A is a 1x13 fiberoptic switch, available for single-mode or multimode fiber connections. These enhance accurate measurements and ease automation with excellent repeatability, fast switching time and flexible interfacing with LAN, USB and GPIB.
-
Product
W-CDMA/HSPA+ Analysis Using NI PXI RF Test Instruments
RFmx W-CDMA/HSPA+
test
The NI-RFmx W-CDMA personality is a highly optimized API for performing physical layer measurements on W-CDMA cellular standard signals. NI-RFmx W-CDMA is completely interoperable with all NI-RFmx APIs. It provides simple access to the most advanced optimization techniques such as multi-measurement parallelism and multi-DUT measurements. The result is extremely fast and high-quality measurements with minimal software development efforts.
-
Product
Scienlab Battery Test System – Module Level
SL1001A Series
Test System
The SL1001A and SL1006A Battery Test Systems – Module Level Series help you emulate sink and source for battery modules for automotive and industrial applications.
-
Product
ARINC-429 Module
M4K429RTx
Test Module
The M4K429RTx is an ARINC-429 multi-channel test and simulation module to be used on the Excalibur 4000 family of carrier boards. The module supports up to ten ARINC-429 channels in any combination of transmitters and receivers. Each of these channels feature error injection and detection capabilities. The receive channels allow for the storage of all selected Labels with status and time tag information appended to each word.
-
Product
Test Handler
M6242
Test Handler
Optimal Test Handler for Mass-Production DRAM, with Double the Throughput.
-
Product
Variable Optical Attenuator Module for Multimode Fiber Applications
81578A
Optical Attenuator
The Keysight 81578A variable optical attenuator is designed for multimode fiber applications and features lowest insertion loss and excellent wavelength flatness over a complete attenuation range of 60 dB, for characterizing optical network components for telecommunication and data communication in systems.
-
Product
Mini Fiber Optic, Patchcord, ITA, 36", Polymer Optic Fiber, to SC
7-413845510-036
Fiber Optic Patchcord
Mini Fiber Optic, Patchcord, ITA, 36", Polymer Optic Fiber, to SC.
-
Product
Hardened SFP+LR/10G-ED, SM1310/LC 20Km
SFP-XSM-LCI-20K
Optical Transceiver
Provides digital diagnostics monitoring (DDM) functionality, Wide specifications and fiber types available, Industrial standard small form-factor pluggable (SFP) package. Comes with metal enclosure for EMI, The Class 1 laser product complies with EN 60825-1, Supports plug-n-play operation.
-
Product
Scienlab Battery Test System – Pack Level, 110 KW Compact Version
SL1710A
Test System
Compact solution for testing Battery Packs with output power up to 110 kW and voltage range up to 1500 V
