Testers
find the limits of a design and assure designed requirements.
See Also: Test, Testing, Specimen, Audio Testers, Automotive Testers, Battery Testers, Cable Testers, Component Testers, Checkers
-
Product
AC/DC Programmable Hipot Voltage Insulation Tester 5KV
7122
-
Shenzhen Chuangxin Instruments Co., Ltd.
Programmable AC/DC Hipot & Insulation Resistance Tester can do hipot test and insulation resistance test
-
Product
Flux Leakage Tester For Detecting Surface Defects In Hot Rolled Black Steel Bar
130MM ROTOFLUX® AC
-
Highly sensitive AC flux leakage is especially well suited to test hot rolled black steel bars and rods that have surface conditions which used to make finding shallow defects very difficult, if not impossible.
-
Product
Friction and Wear Tester
EFM-III Series
-
The EFM-III series is a friction and wear tester for tribology evaluation in conformity with JIS K 7218. This tester is designed for scientific elucidation and technical evaluation of the characteristics relating to sliding friction, wear and lubrication, that are surface behaviors of relative properties of two interacting material surfaces (relative properties of solid materials in relative motion).
-
Product
Partial Discharge Tester (Dry Type)
-
Partial Discharge testing is a way of detecting voids or imperfections in insulators that would lead to overheating and breakdown under normal operating conditions. Due to the nature of the signal being measured, this test is very susceptible to electronic and RF noise and a proper corona-free properly isolated test chamber is required.
-
Product
Gigabit Ethernet Tester
GET-100
-
GET-100 is a handheld 10M/100M/1000M gigabit Ethernet tester, used for the Ethernet installation, operation and maintenance services.The GET - 100 design in a small and portable device which provides packet capture, network monitoring, networkperformance testing, data generation, test leads and error test functions in an organic whole unit. It is widely used in network layer 1/2/3 BER test and RFC - 2544 test. GET-100 help maintenance people to quickly locate fault and analysis network
-
Product
AC Ground Bond Tester
446
-
Our 446 model is a 4-in-1 tester with AC Hipot, DC Hipot, Insulation Resistance, and Ground Bond capabilities. This tester features a simple design and easy-to-use interface, reducing setup time and increasing production-line throughput for your application. The 446 is equipped with multiple memories and an optional USB port for remote BUS communication so you can quickly perform tests on a variety of DUTs from the front panel or with a PC. Add to user safety by equipping your tester with Personal Protective Equipment (PPE) via the built-in safety interlock.
-
Product
HDMI/Display Port Checker with 4ch x 12Gb/s Tunable BERT & EyeChecker
RB1204-HDMI/DP
-
*Low cost continuous 4ch, 1G to 12Gb/s Bit Error Ratio Tester (BERT) and Eye Checker
-
Product
Oil Tan Delta Tester
OTD
-
The Oil Tan Delta (OTD) is a laboratory instrument, which measures the Tan Delta, Resistivity and Relative Permittivity of insulating liquids. These tests give a wider picture of the overall quality of the insulating oil, and will indicate if there is any contamination. Megger has developed features of the OTD to ensure that productivity levels within laboratories are maximised. The microprocessor controlled inductive heater means that there is uniformity of temperature throughout the cell, in compliance with IEC 60247, and for cooling a fan effectively speeds up the cell cooling time. The instrument has a temperature measuring range of 10 to 110 C, with an accuracy of 1 C. It can be set to preheat before testing takes place. The automated oil drain facility negates the need to move the oil vessel. User safety is paramount and with this in mind, Megger have designed independent and dual redundant high voltage cut-off circuitry. If for any reason the user needs to abort the test, this can be done so by pressing any key, immediately terminating the test and removing the high voltage. The design of the cell components maximise oil fill rate but minimise turbulence in oil flow and eliminate trapping of air. With only 32 cell components, it is easy to assemble and disassemble.
-
Product
Core Loss Testers
S30 and S30S Series
-
Stacks built with punched laminations can have a lot of quality issues. Even though the lamination material is tested in sheet format before any process, that alone is not sufficient to guarantee good quality stators. Wear and tear of the punch, bad welding, bad insulating coating in annealing add to the magnetic losses in the stator. It is always advisable to test the stator core in it's final format before winding to ensure good quality throughout the production batch.
-
Product
Diode Module Scanners
Scan500
-
Frothingham Electronics Corporation
The Scan500 scanners are add-on scanners for diode modules, to be used with a tester such as the FEC200.
-
Product
Zero-distance Drop Test System
KRD40 series
-
KRD40 series drop tester, mainly simulates the resistance to drop and impact of large and heavy packaging products. Its strong power system and unique sample holder facilitate easy loading and unloading of oversized and overweight items and automatically rise to the setting. After the height, the drop test is completed. It can realize the drop test of the edge, surface and angle of the sample. This equipment is mainly used to evaluate the ability of product or packaging to withstand drops during transportation and loading and unloading, so as to improve product and packaging design.
-
Product
Vibration Testing System
-
Torontech is now offering Vibration Test Systems, Shock Test Systems, Bump Test Systems, Drop Tester, and Packaging Transportation Simulators.
-
Product
Synthetic Blood Penetration Tester
TN140
-
TESTEX Testing Equipment Systems Ltd.
Synthetic Blood Penetration Tester, is used for the determination of resistance of penetration by the synthetic blood under the different levels of test pressure to medical protective clothing.
-
Product
Torque Testers
-
Torque testers are ideal for a variety of applications in light assembly and can be used to test hand tools, power tools and even pulse tools.
-
Product
High Frequency Insulation Tester
HFIT 7.0
-
The MEDTEQ high frequency insulation tester is a popular device for evaluating compliance with IEC 60601-2-2 and the characteristics of insulation at high frequency
-
Product
Socket Testers & Adaptors
-
Our range of socket testers & adaptors allow users to quickly and simple check the wiring of a socket, clearly identifying polarity faults with and audible buzzer continuously sounding if correct.
-
Product
Analogue (1kV below) Insulation Tester
ST-1503
-
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Measures insulation(MΩ), continuity(Ω) and AC voltage.● Instant operation is possible with a push button, convenient timer is provided with automatic power off after three to five minutes to save the battery power.● LED (red) indication when testing insulation and continuity.● Use of a high efficiency and accurate DC-DC converter.● Most suitable for insulation resistance measurement of electrical household appliances, power line distribution and installation.
-
Product
CCTV Security Testers
-
CCTV Security Tester is a kind of multi-function test tool for CCTV and security camera installation professionals. CCTV Camera Tester is developed aiming to CCTV security system installation and maintenance, combining the following function: Optical Fiber Communication test, low power circuit test, video test and PTZ control, and DC12 1A output for camera test, etc. Helps solving varies problem of security system. It could be also used in laboratory tests, equipment maintenance, etc. CCTV Tester is really an ideal multi-function instrument for CCTV Security System, Optical Fiberal Communication, CATV and other optical fiber networks.
-
Product
Protection Relays Testers
-
Calmet Smart Calibration Devices
A protective relay test includes the review of protective devices in a system. Protective devices and periodic reviews are very important above all for the safe operation of power supply networks. The protective relay test refers to the protective relay.
-
Product
Intelligent Battery Tester
CHROME
-
Simulating a 20 hour discharge test in seconds, the ACT CHROME displays the DC Voltage and available Ampere hour (Ah) capacity of standby lead acid batteries between 1.2Ah and 200Ah.
-
Product
Saluki S2108 Series Optical Network Tester (up to 45dB)
-
Saluki S2108 series Optical Network Tester is an intelligent high-precision optical network comprehensive tester with cloud wireless transmission, intelligent cloud platform and other functions. S2108 series adopts 7 inch capacitive touch screen, supports multi-point touch and integrates 18 functional modules internally. Compared to previous versions, it supports smart cloud platform, iONM, Multi-core measurement, 4G LTE SIM, GPS, Bluetooth and WIFI; built-in 8G storage capacity, can store more than 200,000 test data, and test data can be uploaded to the cloud wirelessly; PDF reports can be generated on the device and transmit them to the mobile terminal via WiFi & Bluetooth. S2108 series supports multi-tasks simultaneous operation, and VFL, OPM, LS functions can run in the background.
-
Product
Bottle Vertical Load Testers
-
Bottle Vertical Load Tester measures the vertical load strength of glass containers, simulating capping and stacking loads.
-
Product
Push Pull Testers
-
Lever-operated manual systems enable rapid push/pull testing up to 220 lbf.Wheel-operated manual systems enable slower, more precise movement with the hand wheel up to 750 lbf.Motorized push/pull testers offer the most control and highest degree of repeatability with the ability to set a constant test speed and range of movement up to 1100 lbf.All push/pull testers can be configured with a digital force gauge with data output for analysis by data acquisition software. An optional digital distance meter to measure displacement is available.
-
Product
Surface And Subsurface EW System Tester
MS 1119
-
CPCI Based BTA is used to test ECM System Processor (80386 & 8051) Boards. This system consists of a Single Board Computer (SBC), CPCI RS422 Communication and Bus Interface Board (CBI), CPCI Digital Input & Output (DIO) Board and CPCI Analog Input & Output (AIO) Board to provide the necessary input/output signals to/from the board to be tested.
-
Product
Brightness Tester
-
A brightness tester can be used for measuring the brightness, whiteness and yellowness of paper, cellulose and other materials like porcelain and plastic. Many brightness tester devices can also measure different colors. The portable devices for professional use that PCE Instruments (PCE) has to offer are particularly suitable for quality control and compliance with ISO standards.
-
Product
Test System
RF-1 ATS
-
The RF-1 ATS is an economical Commercial-Off-The Shelf (COTS) build-to-print tester. The test station is compliant with the published drawing package. The system does not include software.
-
Product
Soft Magnetic Tester
Model SMT-700
-
KJS Associates/Magnetic Instrumentation offers the Model SMT-700 computer-automated magnetic test station for measuring the DC and AC magnetization curves, coercive field strength, and core-loss characteristics of magnetically soft materials, including: Si-Fe, Fe-Co, Fe, stainless steel, Ni-Fe alloys, soft ferrites and others. This modern line of laboratory instruments is designed specifically for accuracy, reliability, and ease-of-use.
-
Product
Chassis Dynamometer Smoke Testers
-
A chassis dynamometer smoke tester (CDST) is used to test diesel emissions when the engine is under load. This is of course a much more realistic test than the commonly used free acceleration test. It is also better for the diesel engine.During a CDST test an automatic test cycle is performed, whereby the emission is measured at different engine loads. The monitor shows checks and actions to perform before the test, shows real-time measuring data and instructions for the driver during the test, and the end results after the test.
-
Product
Optical Tester
Model C
-
The Model C Optical Tester is just such a device. Extremely small geometric distortion and focal length deviation can be viewed and measured easily.
-
Product
Resistor Calibration Boxes
RCB-1
-
Standard Electric Works Co., Ltd
● The RCB-1 is used to verify and proof any High Voltage Insulation Testers. It can be utilized to calibrate all High Voltage Insulation Testers very accurately Analogs or Digitals.● Some institutions and large industries requested their own calibrator too, therefore, SEW started manufacturing the RCB for special customers.
