Line
-
Product
Economic 4-Axis Motion Control Universal PCI Express Card
PCIE-1245E
-
Encoder input is 5 MHz for CW/CCW,P/D,AB modePulse output up to 5 MHzMemory buffer (10 K points) for trajectory planningPoint-to-point, line and E-GearHardware emergency input
-
Product
SP16T RF Pin Diode Switches To 10 GHz
-
Pulsar Microwave's 16-way switches cover 500 MHz to 10 GHz in single pole, 16-throw configuration. Maximum input power is 200 mW and switching time is 100 ns. SMA female connectors are standard. A 15-pin D-SUB male connector makes the internal connections to the power, ground and logic circuitry. Switching control is TTL with the option of line drivers and decoders.
-
Product
PXI BRIC4 FIBO Matrix Dual 62x4 2pin brkout
40-592A-012
Matrix Switch Module
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
Product
Ethernet Parallel Interface
Model 8113
-
* Provides 12 8CMOSL I/O lines for 3.3 and 5 volt logic.* 10/100 MHz Ethernet Interface with Auto-MDIX capability* Robust hardwired TCP/IP (Raw Socket) communication port prevents flooding, spoofing and injection attacks.* Included RS-232 serial control port for older systems.* Optional I2C port for connection to touchscreen panel or other I2C devices.* Standard board has a horizontal Ethernet connector and 150-pin Digital IO connector on the component side.
-
Product
Serial-to-Daq Card
Model 2307
-
* 2307 Board provides 32 digital I/O lines, 4 analog outputs, 6 analog inputs, 6 relay driver outputs and 4 temperature inputs.* Firmware supports ASCII command strings, Addressed commands for RS-485 networks and packet protocol. * Operates as a RS-232 as a RS-485 to Data Acquisition Board. * DE-9 connector has both RS-232 and RS-485 signals.* SCPI commands and IEEE 488.2 compatibility provide GPIB like operation over the serial link. * Runs on 5 Vdc power.
-
Product
ABex in System Programmer with Onboard SMH FlashRunner LAN 2.0 NXG
ABex AM-307 FR-NXG Flashrunner
-
The ABex AM-FR-NXG incorporates the FlashRunner LAN 2.0 Next Generation from SMH Technologies. The FlashRunner is used to program microcontrollers, flash and other logic and memory devices. All DIO’s, the programmable voltage lines and the corresponding ground lines can be switched by relays.The ABex AM-FR-NXG is equipped with an onboard Ethernet Controller which connects the FlashRunner directly to the PXIe Backplane of the ABex Chassis. Using a windows host, each AM-FR-NXG will provide its own network adapter.
-
Product
Gas Stove Production Test Bench
WH-SP-Line
-
Zhongshan Wanhe Testing Equipment Development Co., Ltd
The Gas Stove Production Test Bench (Model WH-SP-Line) is a line-ready final QC station for gas cooker and gas stove production. It offers multi-channel action and tightness testing, automatic pass/fail judgment, and integration with conveyor or MES systems, ensuring that every stove leaving the production line is verified without adding manual cycle time.
-
Product
PipeTRACK Traceable Duct Rodder
-
Ideal for line tracing buried non-metallic telecom HDPE conduits, metallic pipes or utility lines.
-
Product
Guardian Multi-Channel Hipot Tester
19020
-
Chroma Systems Solutions, Inc.
The Guardian 19020 enables users to save space on the production line since there is no need to purchase multiple Hipot testers. Its one time multi-channel test can increase the efficiency of electrical regulatory testing. It improves productivity and reduces the risks of testing for products that require only hipot testing.
-
Product
USB-485/2, 2-Port, USB, RS485/RS422 Serial Interface Device
778476-02
Serial Interface
The USB‑485/2 interface transforms your USB port into a single asynchronous serial port for communication with RS485 and RS422 devices. You can use a USB‑485/2 port as a standard serial port from your application, including RTS/CTS hardware handshake lines. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Voltmeters
-
ARC Flash No Volts Meter is an ultra-safe portable digital voltmeter. It can provide testing of voltage on firing and related system lines. The 620EXV is certified to meet USA MIL. STD. 810 MTD. 511, therefore compliant for use in explosive atmospheres. This product will accurately inform its operator using red and green lights (which can be set to custom levels) to indicate whether or not the voltage level conforms.
-
Product
Process Calibrators
-
Working in process environments such as chemical processing, oil and gas, pharmaceuticals, or food and beverage manufacturing can be challenging work. Maintaining, building, and calibrating process equipment takes specific expertise and often requires specialized process calibrators to get the job done right. With the broadest line of process calibration equipment in the industry, Fluke can help provide you with the right calibration tools for the challenges you face every day.
-
Product
16-bit, 100KHz, 16SE/8DIFF A/D Inputs; 4 14-bit, 30KHz D/A Outputs, 4 24V Digital I/O, All Isolated
APCI-3120-16-4
-
*Optical isolation 500 V*16 SE or 8 diff. inputs*Data transfer rate: 100 kHz*16-bit resolution*4 analog output channels*Data transfer rate:30 kHz*14-bit resolution*Output voltage: 0-10 V, ±10 V, (set through software)*Each output has its own ground line*Driver capacity: 5 mA/500 pF*Short-circuit protection: EMI filters*Data exchange through 16-bit I/O digital*4 digital inputs*and 4 digital outputs, 24 V , opto-isolated
-
Product
Breadboard Module for 34980A
34959A
Breadboard Module
The Keysight 34959A module for the 34980A Multifunction Switch/Measure Unit can be used to create custom designs inside the Mainframe. You can control your circuits with access to both the +12V and +5V supplies, 16 GPIO ports, and 32 relay drive lines. The faceplate has cutouts for the most common connectors. The breadboard module can be programmed using standard read and write commands in SCPI.
-
Product
Affordable EDXRF Analyzers
NEX QC Series
-
Applied Rigaku Technologies, Inc
NEX QC is the lowest cost variant of a line of affordable benchtop EDXRF spectrometers designed for rapid qualitative and quantitative analysis of elements from sodium (Na) to uranium (U) in solids, liquids, alloys, powders, and thin films. For more demanding applications, or for situations where short analysis time is critical, we recommend the NEX QC+ spectrometer. Employing the next generation silicon detector technology, the enhanced NEX QC+ affords significant improvement in elemental peak resolution and counting statistics.
-
Product
Probes
RTD
-
No matter the application, ThermoWorks has a probe for you: penetration probes, immersion probes, air probes, surface probes, wire probes, even specialized probes like griddle probes, burger probes, pipe clamp probes, and probes for medical and lab use. Choose from standard tip, reduced tip, corkscrew tip, alligator clip, or needle probes; different handle types; and straight, coiled, stainless overbraid or even armored cables. Sensor types include type T or type K thermocouples, RTD sensors and our Pro-Series® line of thermistor probes.
-
Product
Device Characterization
-
Probe systems for device characterization must be particularly flexible because many different measurements often must be performed; DC, IV/CV, Capacitance, HF, 1/f, temperature and more. The modular architecture of the PS4L product line is ideal for these broad requirements.
-
Product
Manual Tuners / Impedance Tuners
-
Maury manual tuners are based on precision slide screw technology that utilizes broadband slab line transmission structure and passive probes to create impedances for devices. The probes are designed to be very close to onequarter wavelength in the linear dimension at the mid-band of each range. Since each tuner has two probes, this results in improved matching characteristics for each unit. Another key feature of this series of tuners is the inclusion of a LCD position readout of the carriage position on those units operating below 18 GHz. Higher frequency tuners utilize a micrometer carriage drive. The positional repeatability and high matching range of these tuners make them ideally suited for use as a variable impedance source in applications like device characterization. Such measurements depend upon the ability of the tuner to establish impedances out near the edge of the Smith chart and to reproduce the electrical characteristics as a function of mechanical position. The tuners in this series are also easy to use due to the nearly independent electrical results of the mechanical motions. The depth of penetration of the probe into the transmission line determines the magnitude of the reflection, while the position of the probe along the line determines the phase. While there is some interaction, the effects are almost independent of each other. https://www.maurymw.com/images/mw-rf/mst982e35.jpg
-
Product
Transmission Lines
-
SemiGens 50-ohm Transmission Lines offer the RF/microwave designer complete flexibility and repeatability for the most challenging applications.
-
Product
Compact, Efficient Four-Color Laser Engine
iChrome CLE
-
TOPTICA's iChrome CLE is a compact laser engine that combines four laser lines in one box. All integrated colors are provided via one polarization-maintaining single-mode fiber. It is available with 405, 488, 561 and 640 nm and more than 20 mW guaranteed output power after the fiber each. The system guarantees a plug & play installation since it includes TOPTICA's proprietary COOLAC automatic alignment technology. This way the system is ready-to-use after one simple button click. 561 nm laser light is generated by TOPTICAs proprietary FDDL technology. Each laser line can be directly modulated up to a frequency of 1 MHz and TOPTICA's "Complete OFF" mechanism guarantees zero photons in the "off"-state.
-
Product
Powered VME430 Crates
9U VME430 6021
-
WIENER VME 6021 crate series is the newest generation of generation CERN VME430 compliant VME crates for large size 9Ux400mm cards. Designed for applications in nuclear and high energy physics data acquisition, beam line control and test instrumentation it combines superior mechanical quality with lowest noise power supply technology.
-
Product
LISNs - TEMPEST
-
Com-Power TEMPEST LISNs cover 5 kHz to 1 GHz with two complementary models — LIP-120 and LIP-1000 — rated at 10 A for TEMPEST power line conducted emissions testing in classified government, military, and diplomatic environments.
-
Product
Machine Vision Camera - 2.3 MP, 41 FPS, Sony IMX249, Color
Blackfly USB3
-
The Blackfly® camera line combines Sony CCD, Aptina, e2v, and Sharp sensors with a host of unique features. For FLIR area scan cameras with the latest sensors and most advanced feature sets, please refer to our Blackfly S and Oryx camera families.
-
Product
Laser Tracker Tools And Accessories
-
MetrologyWorks provides a full line of Laser Tracker Accessories as well as Laser Tracker Tooling and Adapters. This includes Drift Nests, Permanent Monuments, Pin Nests, Edge Nests, Hidden Point Bars. If you need something custom we can provide custom Laser Tracker Tooling as well.
-
Product
Imbedded A5 Processor Test Interface
-
Advanced Microtechnology, Inc.
Advanced Microtechnology has extended the application of its Optimum product line with theintegration of ARC5 imbedded test functions. Up to 40 controllers may be independently powered and monitored for functionality using the process test interface of the Optimum WinAOS application. Each part may have 2 separate biases featuring both current and voltage monitoring. Independent test is implemented through a standard JTAG interface. A separate serial clock and command interface may be used if required to provide device initialization sequences. JTAG control is muxed to each part through the use of an independent clock for each part. All of the ARC processor registers and memory space may be tested through the JTAG I/O.
-
Product
Electrophotography
-
Quality Engineering Associates Inc.
Drawing on years of applications experience, QEA has developed a comprehensive line of tools for evaluating EP printer components and sub-systems. This unique family of test systems embodies innovative engineering solutions and a fundamental understanding of the physics of EP processes to give you “must-have” tools for high-speed printer R&D and quality control. These non-contact, non-destructive tools emulate the EP printing process and deliver quantitative data you can rely on. QEA tools are ideal for:
-
Product
Benchtop Analyzer
LabSpec 4 Bench
-
Analytical Spectral Devices, Inc.
Configured specifically for fixed-location analysis with AC power, the LabSpec 4 Bench benchtop analyzer provides all the performance of ASD's LabSpec laboratory spectrometer line in a space-saving and cost-efficient design. The benchtop analyzer features sophisticated near infrared (NIR) spectroscopy at a 10 nm resolution for accurate measurement of a wide variety of materials in real time. Like the portable models, an enhanced spectrometer configuration more than doubles the signal-to-noise performance in the SWIR regions.
-
Product
Large Surface Defect Gauge
4D InSpec® XL Surface Defect Gauge
-
The 4D InSpec XL Surface Defect Gauge expands 4D Technology’s 4D InSpec product line—they’re the first handheld, precision instruments for 3D non-contact surface defect measurement.
-
Product
6GHz Dual Channel Signal Generator 19" 1U Rack Module
LS6082R
Signal Generator
The LS6082R, 6GHz dual channel RF Analog Signal Generator, offers industry leading performance, in a 1U, 19” space efficient, rack-mounted box. The LS6082R features two phase coherent channels, exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. The LS6082R was designed to offer excellent performance and abilities combined with an affordable price tag, needed from the R&D benches to the production lines.
-
Product
Telecommunications
-
TELETEL combines its communication and information systems expertise with its strengths in analogue and digital circuit design to develop products suitable for telecommunication, military and industrial applications. TELETEL's products exist in more than 20 countries in Europe, America and Asia. Every module on TELETEL's product line is designed, developed and tested to meet the increasing demands of today's technology for higher transmission speeds and enhanced system performance.





























