Identifiers
-
product
Static Code Analysis for Embedded Software
GrammaTech CodeSonar®
CodeSonar is GrammaTech´s flagship static analysis software. Able to analyze both source code and binary code, it is specifically designed for zero-tolerance defect environments. With its advanced static analysis engine, CodeSonar is one of the most effective tools for eliminating the most costly and hard-to-find software defects early in the application development lifecycle. Compared with other tools, CodeSonar identifies twice as many defects that result in system crashes, leaks, data races, memory corruptions and security vulnerabilities.
-
product
Cable and Pipe Locator
PT-14
The locator PT-14 is used as an induction signal receiver in a cable tracing and fault location set for the following applications:• tracing – finding the route and determining the burial depth of underground cables and other hidden utilities;• fault location – pinpointing interphase and phase-to-sheath short circuits faults;• cable identification – identifying a correct cable from a bunch.
-
product
Custom Solutions
We provide a friendly, interactive cradle to grave project management service to identify, specify and deliver custom timing equipment to meet your exact needs. Whether this means taking an existing product and refining it or creating a completely new product, we are able to quickly and efficiently do what it takes to satisfy your project needs.
-
product
Loudness Monitoring
The Actus Loudness module lets operators maintain continuous measurements, which among other things, identifies program loudness and loudness range. Loudness measurements combined with robust logging allow users to quickly review the status and provide continuous, exportable measurements as proof of compliance and to defend against loudness complaints.
-
product
Audio Frequency Oscillator
PD-5
2.5- 100 volt output6 position output voltage selectorCompatible with all "Mark" receivers (Mark II, III, IV, V)Pulse "Identifying" signalBattery charging circuit built-inLED impedance meter
-
product
Extra-safety Auto Identify Multimeter with TRMS
VA51 VA51R
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
VA51/VA51R Extra-safety auto identify multimeter with TRMS.
-
product
Metal Detectors
Wuxi IMHOO Technology Co., Ltd.
High performance unit harnesses the power of advanced technology provide with ground balance function to measure ground mineralization and adjust itself for optimum operation, addiction the metal type mode identify the detected subject in ferrous or non-ferrous metal , Enhance the detection depth & accuracy effectively. AR924 is easy to operate, in order to take full advantage & functions of metal detection.
-
product
Optical Fiber Identifier
TW3306
Techwin(China) Industry Co., Ltd
Optical Fiber Identifier TW3306Ais an essential installation and maintenance instrument. By inserting the fiber into its adapter head, it can identify SM optical fibers without any damage by detecting the optical signals being transmitted through them so as to avoid the opening of the fiber at the splice point for identification and thus avoids the interruption of the service.In the presence of traffic, the intermittently audible tone is activated.
-
product
Atlas LCR Passive Component Meter
LCR40
The Atlas LCR40 automatically identifies and analyses almost any passive component (Inductor, Capacitor or Resistor). It measures its parameters using automatically selected test frequencies (DC, 1kHz, 15kHz and 200kHz).
-
product
Professional LAN Cable Tester w. 4 Remote Loopback Plugs
LANTESTPRO
The StarTech.com Advanced RJ45 LAN Cable tester allows a single person to test several long cables faster and more efficiently than ever before. The tester uses remote loop-back plugs that each have their own unique ID number that the tester can identify.
-
product
MT Inspection Scope
Um
● Test 12 or 24 fiber MT Connectors● Find Endface defects fast● 800x Magnification●Numbered Dial Indicator to quickly identify which fiber you're onThe Um MT Inspection Scope accurately shows defects in your MT 12 or 24 fiber connectors. Quickly view each fiber to save time and money. Our unique Fiber Dial shows which fiber you are inspecting. No more getting lost!The Um MT is compatible with our Eagle Inspect Software. Create reports with images for your MT connectors.
-
product
Transient Absorption
Our Transient absorption spectrometers use a powerful set of techniques used to identify electronic and structural characteristics of short-lived excited states (transient states) of photochemically/photophysically relevant molecules.
-
product
Situational Awareness
SA is utilized to secure borders from illegal trafficking, to monitor supply line routes against the placement of roadside bombs, to provide our warfighters the tools they need to alert them to potential threats, and to identify and defeat the enemy, day or night.
-
product
Saluki S2107 Series Optical Cable Identifier (up to 36dB)
S2107 Series Optical Cable Identifier is an intelligent instrument designed for the construction and maintenance of optical cable lines in optical communication system. In view of the complex wiring environment and the difficulty of locating faults during the construction and long-term use of optical cables, S2107 series can provide fast, effective and accurate fault solutions. When the target optical cable is bent or shaken, the optical cable census instrument can quickly capture the vibration signal and display it through waveform and sound, so as to locate the target optical cable quickly.
-
product
Satellite Signal Level Meter
Super Buddy
Complete more installs faster and better using the Super Buddy satellite finder meter. Be "sure of your bird" with the positive ID feature or use the automatic scan to identify the unknown satellite. The Super Buddy's geo-sensitive "Field Guide" shows you just the birds visible to your install -- ALL of them, with their individual transponders. The Super Buddy even gives the elevation and azimuth for whichever satellite you select.
-
product
Visual Fault Locators
Optical Wavelength Laboratories
OWL fiber optic visual fault locators (VFL) are specially designed to couple a maximum of optical energy into multimode and singlemode optical fibers by using a bright red fiber optic laser. Breaks, microbends, and other anomalies in optical fibers and connectors cause the intense bright red laser light to escape, thus revealing the presence of a fault. In addition to visual fault location, OWL VFLs can be used as a visual optical fiber identifier. A visual fiber optic identifier eliminates much of the guesswork during testing by identifying the fiber under test.
-
product
Testing and Measurement
AkroMetrix provides a variety of products to help you identify and evaluate warpage: For warpage measurements along a production line or at room temperature, AkroMetrix has developed the LineMoiré Production Level Automated Flatness Inspection System. If you need to measure warpage and flatness during pre-defined temperature profiles, AkroMetrix's TherMoiré In-Process Warpage Measurement Systems may fit your requirements.
-
product
Cable Identifier
OFI-50A
OFI–50A uses optical fiber sensing principle to confirm the target fiber; It can quickly identify deep buried, overhead and pipe fiber cable without any destroy, and provide a simple method for maintenance personnel. Users only need gently knock on cable, when knocking to the target cable, OFI-50 can clearly hear the knock from earphone, which can accurately identify the target cable.
-
product
Structural Test ICP® Accelerometers
Conventional structural test data systems use few to several hundred sensors. Cables bundles can be complex and confusing resulting in setup errors. Sensors with TEDS (Transducer Electronic Data Sheet) allow for an internal sensor digital chip to store sensor information. This information contains descriptive identifiers that when connected to a TEDS compatible signal conditioner or data system, reads the descriptive information and automatically aligns the data system. Human error is minimized, reducing time consuming data verification or re-test. The Series 333 ICP® accelerometers, and their accessories, are designed to address the needs of multi-point modal and structural test measurement applications. This equipment was developed in conjunction with the world renowned University of Cincinnati Structural Dynamics Research Laboratory and proven in real-world testing situations. The PCB 333 Series accelerometers delivers rapid system setup, reduces human documentation errors, maintains calibration data of each sensor, allows for “Plug-and-Play” installation, reduces overall test time lowering project test costs.
-
product
Conformal Coating Inspection (CI AOI)
They cover the components, the area around the components and identify most coating issues including cracks, bubbles, insufficient / excess coating, loss of adhesion and other common contaminations. Full coverage inspection for conformal coating.
-
product
High-Speed Adapter
DDR Pro
Introducing the DDR Pro adapter, the latest advanced test adapter for RAMCHECK. This new high-speed DDR test adapter features advanced circuitry and a powerful high-frequency test engine, allowing you to fully test and identify PC433/466 DDR modules, with planned upgrades to 533MHz.
-
product
Turnkey NDT Corrosion Inspection Services
Robot-enabled ultrasonic inspection that produces thickness grid maps to identify areas where corrosion and other damage mechanisms have caused wall-thinning.
-
product
ESD Discharge Simulator
Model 9910 PurePulse/PinScan
Model 9910 PurePulse / PinScan is used to determine the ESD susceptibility level of electronic devices up to ±4kV. PurePulse generates ESD pulses up to 4kV for testing electronic devices for susceptibility to Electrostatic Discharge (ESD) using HBM, MM and HMM models. PinScan provides automatic sequencing of ESD testing of up to 128 pin devices, applying a discharge, thenperforming a curve-trace test to identify a failure.
-
product
Time Domain Reflectometer (TDR) Card
PCI-3127
The PCI-3127 is a PCMCIA-form factor TDR that can be used to identify and locate failures in installed wiring and cable systems. The instrument can make high resolution TDR measurements on circuits up to 96,000 feet (~30km) from your Windows XP notebook computer or PC using a low-voltage non-destructive test signal.
-
product
Software
SSI-TRES
Was developed to read and edit Plug and Play Smart Sensors that are compliant to the IEEE 1451.4 Standard. TEDS, or transducer Electronic Data Sheet, is a set of electronic data in a standardized format defined within the IEEE 1451.4 standard. This data specifies what type of sensor is present, describes its interface, and gives technical information such as sensitivity, bridge type , excitation, etc. This information is stored in an EEPROM chip attached to the sensor. By having this chip, the sensor can identify and describe itself to the network and or Smart Load Cell Meter (DPM-3), thereby easing automatic system configuration.
-
product
Electronic Brake Meter
2000-R
The Bowmonk 2000-R is our next generation electronic brake meter, featuring a built-in printer, keyboard, GPS receiver, and coming soon built-in Wi-Fi for automatic uploading of brake test results. Significant processing power and on-board storage enables the Bowmonk 2000-R to be customised for various applications. The Bowmonk 2000-R also supports an optional pedal force transducer to measure the force applied to the vehicle's footbrake during braking. Using the pedal force transducer will also identify any "braking delay" - the time between depressing the brake pedal and the brakes being applied.
-
product
Advanced Laser Source
SLS-50
SLS-50 can generate highly stable optical signals at multiple wavelengths to precisely measure optical link loss and identify optical fiber paired with ShinewayTech OPM-50 Intelligent Optical Power Meter.
-
product
Analyze RTL
ASICs and FPGA routinely have millions of gates with memories, transceivers, third party IP and processor cores. Problems can be time consuming and complex to debug in the lab and through simulations. Designers need verification tools that can identify problems quickly to reduce their verification and debug time before simulation, before synthesis, and definitely before burning chips in the lab.
-
product
RTOS Scheduling Visualization
RapiTask
*Examine Ada, C or C++ applications via scheduling visualization*Locate rare timing events that need attention*Identify bottlenecks in your application by analyzing capacity issues*Compare scheduling algorithms from different RTOSs
-
product
Cable Locator (LCD type)
5501 CB
Standard Electric Works Co., Ltd
● The 5501 CB transmitter is a great tool for locating and identifying cables and individual conductors● Locates both powered and unpowered cables ● Voltage measurement for cables: ACV 12V~450V DCV 12V~450V● Signal transmission • Transmission power level selection (includes 1, 2, 3) • Transmission signal code selection (includes F, E, H, d, L, C, O, A)● Flashlight & backlight function● Silent mode (disable button beep)● Level bar display on LCD screen (transmission power level indication)● Action wave display on LCD screen (when signal is transmitted)● Auto power-off function
