Identifiers
-
product
Primary Injection Test Systems
Primary current injection testing is utilised in high current/high voltage scenarios found at large electrical installations such as substations. A large current (between 100A and 20,000A depending on system specifications and test requirements) is injected directly on the primary side of the electrical system such as a circuit breaker. The objective of the test is to identify how the system operates under various levels of current load.
-
product
Square Root - Gauge Line Error Indicators
Parker PGI's SRE6 and GLE6 Indicators are designed to quantify Square Root and Gauge Line Errors in natural gas orifice flow measurement. They identify inaccuracies caused by compressor-induced pulsation and differential pressure discrepancies.
-
product
Mineral Identifier
TerraSpec Halo
Analytical Spectral Devices, Inc.
For exploration and mine geologists, the PANalytical ASD TerraSpec Halo mineral identifier is the next generation all-in-one mineral analysis system that allows you to immediately identify alteration minerals with a simple pull of a trigger for faster delineation of alteration, speedier core logging and quick confirmation of ore mineralogy.
-
product
Open Source Software
Automate OSS selection and approval, identify applicable risks in OSS libraries and container images, reduce SCA noise by 80%, and implement accurate SBOMs.
-
product
Fault Locating
Schweitzer Engineering Laboratories, Inc.
The built-in fault-locating methods in SEL devices allow you to quickly identify faults, dispatch crews for repairs, and restore service faster. Traveling-wave fault-locating technology calculates the locations of temporary and permanent faults by measuring the arrival times of the naturally occurring traveling waves caused by a transmission line fault. Accurately detecting these waves requires ultra-high-resolution monitoring, and locating is accurate to within one tower span (±300 m). Impedance-based fault-locating technology calculates fault locations by detecting changes in line impedance as a result of a fault. Impedance-based locating is reliable and accurate to about 2 percent of a line’s total length.
-
product
Armature Tester
Qingdao AIP Intelligent Instruments Co., Ltd
This tester is suitable for online or offline detection of various armature electrical properties, such as power tool motors, garden tools, vacuum cleaner motors, small household appliance motors, automobile motors, fitness equipment motors, permanent magnet micro-motors, etc. The tooling of the tester meets the requirements of arbitrary placement of the armature, and can automatically and accurately sort/track faulty solder joints; the equipment startup methods include buttons, remote control, and sliding cover; it meets the armature test of special processes such as double insulation, and automatically identifies solder joints, winding short circuit/open circuit , winding errors, poor welding and other problems; the tester can also automatically count the number of tests, the number of defectives and other data, which is convenient for quality management analysis.The tester test items mainly include:bar-to-bar resistance, diagonal resistance, welding resistance, insulation resistance, ac hi-pot, surge.
-
product
Metallurgical Testing Services
BMP Testing and Calibration Services Inc.
Metallurgical testing is a crucial part of metal processing and manufacturing and is used in almost every industry — aerospace, shipbuilding, steel, construction, and many others. It involves the use of a wide range of techniques and equipment to identify the material type, potential defects, and processing errors.
-
product
Sequence / Rotation Indicators
Phase Sequence and Motor Rotation meter detects live phase and sequence orientation of three phase power sources and industrial equipment conductors to ensure proper installation. Motor rotation function identifies rotational direction of industrial equipment such as motors, compressors and generators. Non-Contact Motor Rotation feature determines rotation of running single-phase and three-phase motors without the use of leads.
-
product
Reticle Manufacturing
An error-free reticle (also known as a photomask or mask) represents a critical element in achieving high semiconductor device yields, since reticle defects or pattern placement errors can be replicated in many die on production wafers. Reticles are built upon blanks: substrates of quartz deposited with absorber films. KLA’s portfolio of reticle inspection, metrology and data analytics systems help blank, reticle and IC manufacturers identify reticle defects and pattern placement errors, thereby reducing yield risk.
-
product
Air Core Inductors
Osborne designs our Air Core Inductors to realize their advantage of high linearity. We also work with our clients to identify and mitigate any potential disturbances that could result from electromagnetic fields created. The air core design approach is known to create strong electromagneticfields. Osborne develops electromagnetic circuit models, if necessary, to ensure that our clients build effective and reliable circuits.
-
product
Sola-Sure System
Health & Safety solution to support the industries where dangers may exist of UV lamp radiation coming into contact with human skin. Increasingly driven by national and government regulations the Sola-Sure identifies higher energy radiation that can cause damage to humans in solarium, medical treatment and the industrial UV work place.
-
product
Code Verification Systems for Quality Inspection
Matrix codes enable the comprehensive and seamless traceability of goods, which turns out as significant advantage considering everyday product recalls across all industries. Whether salmonella in food, contaminated cosmetics or poor components: defective products can harm consumers, cause losses of image as well as massive economic losses. Using the 2D code, each individual article can be localized globally. Based on the specific serial number, producers and consumers can clearly identify articles if required. That represents a perfect tool for determining whether the article is subject to be withdrawn from circulation. The proper application and specification of 2D code contents allows for serious and sustainable companies to limit recalls, save costs, and to take responsibility for consumer protection.
-
product
Laser Fault Locator
FOD 111
The Laser Fault Locator FOD 111 is a Laser Source with an output power of 1 mW in SM or MM fiber. It works from two AAA batteries. The universal adapter allows to use the Laser Fault Locator FOD 111 with all popular connectors without changing the adapter. If you need to test a patchcord, to find fiber breaks, or identify one fiber from ten - this instrument is for you!
-
product
Pharmaceutical Climate Test
CP series
Our Pharmaprfschrnke have been specifically designed for long-term and stability testing in the pharmaceutical industry and have very small tolerances. With these test chambers can be the shelf life of different products such as check medicines and identify suggestions for optimal storage conditions.
-
product
Check Weighing
You run containers all day (and sometimes all night) at light speed. Of course there are minor mistakes or issues from time to time. If you know there is an issue or even if you aren’t sure, let FlexXray do a weight inspection for you. We’ll identify any abnormalities and help you address them quickly and efficiently.
-
product
Capacitance Detection Probe
Which Ender
By sensing capacitance the Which Ender identifies if a wire is connected to a contact. When the Which Ender's button is pressed, a tone is produced. If a contact is connected to a wire, this tone will drop in pitch when the probe tip touches the contact. The Which Ender is essential for locating opens, breaks, and unused pins in connections.
-
product
Bus Analyzer, Exerciser, Emulator, and Programmer
CAS-1000-I2C/E
While the I²C interface seems simple on the surface, this straightforward architecture is not immune to intermittent glitches, device misbehaviors, and protocol violations. Likewise, tracking down these errors can be tedious business if the right tool is not utilized.The CAS-1000-I2C/E bus analyzer is an exceptional tool for pinpointing I2c irregularities. The ability to spot complex problems and identify invisible obstacles make it the preferred I²C development solution. Advanced logging, debugging, emulation, and verification capabilities offer power and versatility, yet the Windows-based user interface makes the most complex features simple to use.The CAS-1000-I2C/E succeeds where simple monitoring and interactive I/O tools fall short—a complete solution to monitoring, emulating, stressing, and characterizing I²C and SMBus interfaces.
-
product
LED Light Tester
The T100L Automatic LED Light Test Equipment is designed to identify the presence of any defects of electronic components for LED light applications, addressing any high-volume production testing challenges without needing expensive test fixtures with fiber optics
-
product
Heating Microscope
Heating microscopy is a non-contact technique that, based upon an advanced image analysis of a specimen subjected to a thermal treatment reproducing industrial firing conditions, identifies several characteristic shapes and related temperatures key to the optimization of manufacturing processes in ceramics, metals, and alloys.
-
product
Battery Test Packages
Explorer Technology Group (ETG)
ETG offers a full range of battery test kits which speed and simplify the process of collecting battery test data . This data can then be downloaded and analyzed with the included Winmeter 5.1 Battery Analysis Software, enabling the user to quickly identify batteries that are likely to require preventative maintenance.
-
product
Tone Generators
Traditional Tone Generators were designed for one primary mission; to identify the termination point of a cable. Unfortunately, these were designed for telephony, not network maintenance.
-
product
Hydrogeology
HAPPIE
The H.A.P.P.I.E. program (Hazard of Aquifer Pollution Potential Impact Evaluation) provides a conservative answer to the problem of determining risk levels in emergency conditions, which means that areas where illegal waste disposal sites, overflows and ruptures of impermeable sheeting are present and where water withdrawal should be discontinued can be identified. H.A.P.P.I.E. in fact offers a conservative response to the problem of the determination of the environmental impact in critical conditions that can usually be correlated to the requirements of defining areas in which the supply operations should be interrupted in emergency conditions, therefore in very short times and without the possibility of obtaining an accurate collection of the hydrogeological data.
-
product
Cable Tracers
180 CB
Standard Electric Works Co., Ltd
● The Amplifier Probe is designed to identify and trace wires or cables within a group without damaging the insulation.● Works with any Tone Generator to identify wires.● Volume control for increased sensitivity and adjustable to suit work environment.● Recessed ON/OFF button prevents battery drain.● A phone jack is designed for headset or handset.
-
product
Industry Standard in GPR for Utility Mapping and Locating
GSSI’s Utility Scan Pro GPR
Geophysical Survey Systems, Inc.
With UtilityScan Pro, users can quickly identify and mark the position and depth of metallic and non-metallic objects; including utilities such as gas, communications and sewer lines as well as underground storage tanks and PVC pipes. Based on the SIR 4000 controller, the UtilityScan Pro provides the GPR professional with solutions to any underground locating situation.
-
product
Clinker Detection System
CDS
The Clinker Detection (CDS) System is an ITM proprietary technology for measuring both the size and frequency of deposits that impact a utility boiler floor or bed. This technology enables operations personnel to shorten boiler outages, identify fouling problems and optimize soot blower operations.
-
product
Usability Testing
Using our proven testing usability methodology, we deliver a 360-degree view on a product's operability by analyzing, identifying and benchmarking the weak spots in core features of the application and suggesting opportunities for improvement.
-
product
Advanced Identify Friend Or Foe (IFF) System
Model MD500L IFF
Kratos Defense & Security Solutions, Inc.
The Model MD500L IFF Transponder is an L-Band augmentation device ideally suited for use in aerial target drones, unmanned vehicles, and cruise missiles as a radar enhancement device that provides automatic radar identification in response to interrogations from L-Band IFF and Air Traffic Control (ATC) radars. It also supports Mode C (altitude reporting) operation.
-
product
Power Line Meter
The Line EMI Meter measures electromagnetic interference in a single-phase AC power line. It plugs into a wall outlet (mains socket) and requires no battery. It immediately displays total line noise in millivolts (range 1999 mV, resolution 1 mV) in the frequency range 10 KHz 10 MHz (the frequency limits at which sensitivity is of the maximum sensitivity). A speaker plays the sound of the EMI, amplitude demodulated, in order to identify the EMI source (such as an AM or shortwave radio station vs. a motor vs. an electric arc).
-
product
Relay Circuit Tester
RCT76
Quickly identify electrical problems in an entire circuit at the push of a button. Test the component on a circuit to determine if it is functioning correctly.
-
product
Automotive Electronic Stethoscope
77109
Helps to identify engine and chassis noise. Maintain all health and safety precautions whilst using on running engine. Helps to identify engine and chassis noise. Powered by a 9volt battery (not supplied). Complete with headphones and volume control. CE certificated.
