TWT Amplifiers
generate high power RF signals. Also known as: Traveling Wave Tube Amplifiers, TWTA
See Also: Microwave Amplifiers, Traveling Wave Tube Amplifiers, TWTA
-
Product
Test & Measurement Instrument Amplifiers
MPA-series
-
The MPA-series Test & Measurement Instrument Amplifiers are based on state-of-the-art GaN PA modules and operate from 0.7 to 26.5 GHz (multiple frequency options are available). They provide High continuous power across the band, high linearity for wideband communications testing, have variable gain adjustment and a high-resolution display shows amplifier status. Amplifiers offer a wide range of application-specific requirements including simultaneous high-power, wide bandwidth, low harmonic power and high linearity.
-
Product
Solid State Broadband High Power Amplifier 1900 - 6000 MHz / 200 Watts
2215
-
The 2215 is suitable for octave bandwidth high power CW, modulated and pulse applications. This amplifier utilizes high power GaN devices that provide wide frequency response, high gain, high peak power capability and low distortions. Exceptional performance, long-term reliability and high efficiency are achieved by employing advanced broadband RF matching networks and combining techniques, EMI/RFI filters, and all qualified components. for EMC, RF Product Test, Communications and Electronic Warfare applications.
-
Product
Load Cell Amplifier Signal Conditioner with DB9 Connectors
MODEL LCA-9PC
-
The LCA-9PC Module provides low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-9PC comes with DB9 male and female connectors, which require soldering to user-furnished mating female or male wire connectors. On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film otentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
Product
Distribution Amplifiers
-
Step up to a leading range of distribution solutions. Take a single input signal and feed it to multiple locations while still maintaining guaranteed signal quality. Choose from our range of solutions for every need and every budget.
-
Product
Power Amplifiers (MCPA)
-
*Multi-Carrier Power Amplifier supplies an additional 12.9 dB of Gain at high power*Supports iDEN in the 850MHz Band, available for GSM in cellular and PCS configuration*High power handling with low IM and insertion loss*Ideal for combining multiple BTS to a single feeder line and providing increased power to the antenna
-
Product
Converter Signal Amplifier – 4…20 mA – Wall Mounting
HD978TR5
-
Configurable converter signal amplifier with 4…20 mA (20…4mA).
-
Product
Ring-Loop TWTs
-
Communications & Power Industries
Small and lightweight products for pulsed radar and most advanced designs for commercial, electronic warfare and radar systems, the unique ring-loop slow-wave structure used in these CPI BMD traveling wave tubes provides high gain at kilowatt peak RF power levels without oscillation and achieve greater than 30% efficiency.
-
Product
Low Noise AC Amplifier
MA-164A
-
LOW NOISE AC AMPLIFIERS. Battery powered, rechargeable. Low distortion. Upper and lower bandpass limit selection switcher. 10dB step gain switch
-
Product
Distribution Amplifier
-
AVLINK TECHNIC TAIWAN CO., LTD.
Is a device that accepts a single input signal and provides this same signal to multiple isolated outputs.These devices are important because they allow a signal to be distributed to multiple destinations without ground loops or signal degradation. They are used for a number of common engineering tasks, including multiple amplification, cable television, splitting monitor and front of house mixes, and "tapping" a signal prior to sending it through effects units to preserve a "dry" signal for later experimentation.
-
Product
Operational Amplifiers
Op Amps
-
Operational amplifiers, known also as op amps, play a major role in analog signal conditioning applications. Invented by Karl Dale Swartzel Jr. in 1941, these products are largely used in today’s electronic devices.
-
Product
Femtosecond Multipass Ti:sapphire Amplifier
MPA 50
-
MPA 50 is a multipass Ti: sapphire amplifier based on a two-mirror confocal design and containing a pulse stretcher, a pulse compressor, a pulse picker, synchronization electronics, and the Faraday isolator.
-
Product
Power Amplifier For Real-Time Dynamic Simulation(RTDS) Application
-
As the first power amplifier manufacturer in China, PONOVO has been offering various power amplifier products for customers in China and other countries since 2001. PONOVO has launched both conventional power amplifier for power system use and also 4-Quadrant power amplifier for more filed application, such as microgrid, windfarm, PV, HVDC, areospace, battery simulation, etc.
-
Product
SW Range Broadband Power Amplifiers 0.8 GHZ - 4 GHZ
SW Series
-
Class A solid stateBroadband (instantaneous single band): 0.8 GHz 4 GHzTypical output power : 18 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 13 W and H < -20 dBc up to 2.5 GHz andP1dB > 12 W and H < -20 dBc from 2.5 GHz to 4 GHzAir cooling: self contained fansCan operate in full mismatch conditions without damageReliable, efficient and robust19" Rack3 years standard warranty
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Stand Alone/ Bench Top Load Cell Amplifier/ Conditioner Module
MODEL TMO-2
-
The TMO-2 Transducer Modules is a complete differential amplifier/signal conditioners with self contained power. The units provide excitation, balance and span adjustment via precision 10 turn pots, and shunt calibration necessary to couple a user supplied bridge type transducer to an indicating instrument. Full scale output is specified at plus or minus 10 VDC. The TMO-2 provides a floating shunt calibration circuit which applies calibration at the transducer, thereby eliminating errors due to line losses. The excitation supply incorporates a Wagner Ground to greatly improve Common Mode Rejection. The factory set bandwidth of the module is narrow to improve stability for applications such as weighing scales. The removal of a single capacitor will increase the frequency response DC to 60K Hz for dynamic data applications.
-
Product
VHF Band 1.0 Watt Amplifier With RF Bypass
-
Teledyne RF & Microwave has developed a 35 to 350 MHz custom amplifier with 1 watt output power. The amplifier has 29 dB gain with 3 dB noise figure. The amplifier assembly has a RF switch so that the RF input can be connected directly to the output bypassing the amplifier. The amplifier goes into the "bypass" state when the DC bias is removed from the switch. This unit is one of a series of amplifiers that covers the 1 MHz to 2100 MHz with similar operation.
-
Product
Waveguide Amplifiers
-
VDI offers waveguide amplifiers for various applications. Waveguide amplifiers are able to boost a small input RF signal to a large output RF signal. For sample data on waveguide amplifiers, please refer to the Waveguide Amplifier Product Manual (also located under Resources). Please contact VDI for more information.
-
Product
High-Voltage Amplifiers - to 1000 Volts peak-to-peak
-
These amplifiers provide high amplitudes and bandwidths, and are well suited for use as booster amplifiers for lower-voltage arbitrary waveform generators.
-
Product
Saluki SE1022 DSP Lock-In Amplifier
-
SE1022 Digital Lock-in Amplifier provides an excellent performance within its bandwidth from 1 mHz to 102 kHz. With the advantage of the latest digital signal processing technology and high-precision 24-bit ADC, SE1022 can easily detect the phase and the magnitude of weak signals overwhelmed by various large noises. The performance of SE1022 is as good as other lock-in amplifiers brands, even better in some certain parameters, such as measurement accuracy, SNR, dynamic reserve. Otherwise, SE1022 integrates some special functions like multiple harmonic measurement and FFT, which meets the needs of scientific research and industrial application well.* Saluki SE1022 can be comparable to SRS SR830, even better and more stable.
-
Product
FTTx PON Optical Amplifier (1540~1563nm)
HA5800E (5RU)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
HA5800E (5RU) series is a low noise, high performance, FTTP high power, multi-ports optical amplifier with gain spectrum band within 1540~1563nm. Each output port for optical amplifier has built-in well-performed CWDM. Every external up-link optical port of optical amplifier can connect with OLT PON port very conveniently. Each 1550nm (CATV)'s output optical port multiplex 1310/1490n's data stream, in order to reduce the quantity of the component and improve the index and reliability of the system.
-
Product
Scaling Amplifier
SIM983
-
Stanford Research Systems, Inc.
The SIM983 Scaling Amplifier provides fine adjustable gain and offset control for analog signals. Both gain and offset are set with 3½ digits of resolution, and the signal path has more than 1 MHz of bandwidth.
-
Product
Medium-Power, Broadband Amplifiers
-
Our family of distributed amplifiers utilize advanced broadband design techniques to achieve solid performance in gain, flatness, noise figure and output power over a wide frequency range. The experienced design team has the know-how and tools available to take any standard product and customize it for your specific application.
-
Product
4-Quadrant Power Amplifier
PAV10000
-
PAV Series Four-quadrant Simulation Power Amplifier based on linear power amplifier technology and integrated advanced technical performance and rich functions.
-
Product
Amplifier Module
LNAM-LPA
-
We offer an evaluation board and case for the LNAM-B and LNAM-FBX modules. This Laboratory PreAmplifier (LPA) solution is powered by a switch-mode power supply and gives access to the LNAM in- and outputs via BNC sockets.
-
Product
Power Amplifiers
WBPA Series
-
Besides offering wide bandwidth, WBPA series wide band power amplifiers have exceptional gain flatness and ultra high linearity. The IP3 are from 40 dBm to over 50 dBm. The different models cover the frequency bands of VHF, UHF, Celular, GPS, DCS, PCS, 3G, MMDS, and S band. The amplifiers have optimum return losses, gain flatness, high power and high added power efficiency, wide bandwidth matchings, and unconditional stability.
-
Product
Charge Amplifier
CH-1200A
-
CH-1200A is a high-performance charge amplifier to convert charge signal to voltage signal. Built-in integration function allows optimization of the signal which is input to the vibration data analyzer connected.Changing into a multi-channel amplifier is easy by connecting multiple units.
-
Product
Gain Shape Linearizer Amplifiers
-
Gain Shape amplifiers are used in a number of applications where it's necessary to flatten the gain characteristic of the preceding or following component. This would include flattening the attenuation of a long cable run or perhaps changing the input gain response to a MPM (Microwave Power Module) or TWT (Traveling Wave Tube) to compensate for the gain variation within the tube.
-
Product
Amplifiers
-
Teledyne Lincoln Microwave design and manufacture RF amplifiers utilising the latest semiconductor technology. Our portfolio includes low noise amplifiers (LNA’s), power amplifiers and pre-amplifiers. These can incorporate linearization, filtering, phase and amplitude control functionality.
-
Product
Solid State Power Amplifier Module (SSPA)
-
Macom Technology Solutions Holdings Inc.
MACOM’s Solid State Power Amplifier (SSPA) and waveguide module product portfolio leverages our world class MMIC technology and system design expertise for high performance Industrial, Aerospace, Defense, and Communications applications. Our SSPA modules feature up to 16 power-combined MMICs in a single module and we can power-combine multiple modules up to 100GHz featuring either coaxial or waveguide interfaces.
-
Product
Combustible Trip Amplifier Module
TA102A
-
The TA102A is a single-channel Combustible Gas Trip Amplifier Module designed for use with one General Monitors intelligent transmitter to monitor combustible gases and vapors within the lower explosive limit (LEL) and provide status indication and alarm outputs. Microprocessor-based electronics allow all options to be user selectable through a front panel interface (mode / select switch and digital display).
