Voltage Preamplifiers
-
Product
Voltage Dip & Swell Simulators
VDS Series
-
A simulator to reproduce voltage variation phenomena in commercial power supplies (AC100V/200V).This type of immunity test against voltage variation phenomena is defined in IEC 61000-4-11 and is widely used in many industries.
-
Product
Isolated AC Voltage Input Module
ADAM-3112
Voltage Input Module
0 ~ 450 VAC to 0 ~ 5 VDCAC voltage measurement1,000 VDC isolation between output and power2,500 VAC isolation between output and inputInput impendent: 2 MohmMulti input modesAccuracy: ±0.1% FSRFlexible Din-rail mountingOperates from a single +24VDC
-
Product
DC Voltage Sensors
-
DC voltage sensors monitor input voltages ranging from 3 to 500 volts DC with a trip point accuracy of up to 1% in airborne, military and ground power applications. Using internal electronic circuits to detect, monitor and/or sense DC voltage, DARE DC voltage sensors, monitors, and voltage sensing relays can open or close a circuit when a certain pre-set over or under voltage condition exists or the DC voltage falls outside the specified voltage band window.
-
Product
Relay Testing Voltage Source
PTE-FCN
-
It is the easiest and most economical way of increasing the relay types that can be tested with the PTE-100-C. The PTE-FCN includes its own LCD display and a BUS-PTE connection, which makes it easier to operate and enables it for use in combination with any other test set in the PTE range. The PTE-FCN is included as standard in models PTE-100-C Pro and PTE-50-CE Pro.
-
Product
Voltage, Continuity, and Current Tester
FLIR VT8-Series
-
The FLIR VT8-Series are high-quality voltage, continuity, and current testers. They feature an optimized, open-jaw design that can fit into tight spaces and reliably measure large-diameter cables. The VT8-600 carries a CAT III-600 V/CAT IV-300 V safety rating and a 100 A/600 V measuring range, while the VT8-1000 carries a CAT III-1000 V/CAT IV-600 V safety rating and a 200 A/1000 V measuring range. Extensive measurement features make the VT8-Series versatile tools – just one meter can get the job done.
-
Product
Voltage Testers
DUSPOL
-
BENNING Elektrotechnik und Elektronik GmbH
phase-sequence test (counter-clockwise / clockwise)single-pole phase test: " symbol (red LED)measuring point illuminationacoustic and optical continuity testfrequency measurement 1 1000 Hzvoltage indication 1 1000 V AC TRUE RMS / 1200 V DCresistance measurement and diode test with conducting-state voltage indicationlc display with background lightingsensor of non-contact cable break detectorload connection via large-scale push buttonsvibrating alert in the test handleshock-resistant housing with protection against dust and water jets (protection class IP 65) and rubberized test handleDIN EN 61243-3 (VDE 0682-401): 2015 standard
-
Product
Over Voltage Protector
KAB 5A
-
Konstar Electric Industrial Co., Ltd
The voltage is too low or too high, the protector will cut off the power automatically, when the new power supply, the protector will delay 10S-300S to make electrical appliance start to work on the stable state.The voltage protector suitable for A/C, refrigerator, TV, computer, wash machine and other home electric appliance.
-
Product
AC High Voltage Breakdown Tester
CIE / 5050A
-
Cambridge Instruments & Engineering Co.
'CIE' A.C. High Voltage Breakdown Test Set is ideal for fast accurate & reliable testing of withstand/Breakdown test of electrical & electronic materials, components, equipments, panel boards, etc.
-
Product
PC Controlled High Voltage Testers
-
PC-controlled high voltage testers are instruments that use a computer to manage and control the testing of electrical components or systems at high voltages, often for insulation integrity or dielectric strength testing.
-
Product
High Voltage Measuring System
-
Our company is counted among the topmost manufacturers and exporters of High Voltage Measuring System. In strict accordance with industry standard parameters, this testing system is manufactured using excellent quality raw materials. Our range includes different technical specifications and models to satisfy clients' varied demands. We offer this High Voltage Measuring System to clients at economical price.
-
-
Product
PXI High Voltage Multiplexer, 12-Channel
40-320A-001
Multiplexer Module
The 40-320A-001 is a single 12-channel MUX and is part of our 40-310/320A range of High Voltage Switching Modules which will hot switch up to 750V peak and cold switch up to 1000V peak in either general purpose relay (40-310) or multiplexer (40-320A) configurations.
-
Product
Portable Voltage and Current Instruments
-
Each model in our portable test equipment range is designed for accuracy and reliability, providing high performance and ease of use for applications. Products are used in various lab and field applications across industries such as research and development, semiconductor, and process control. For higher range electrical source and measure we have a series of bench multifunction calibrators and multimeters.
-
Product
High Voltage AC/DC Dividers
-
Sphere Gaps are absolute standards for measurement & calibration purposes of high voltage equipment Sphere Gaps from 20mm to 1500 mm are available. The Sphere Gaps are provided with automated controls with digital display.
-
Product
High Voltage 50 Ω Pulse Generator
TLP-4010C
-
High Power Pulse Instruments GmbH
*Wafer and package level TLP/VF-TLP/HMM testing*Ultra fast 50 Ω high voltage pulse output with typical 100 ps rise time*Built-in HMM (IEC 61000-4-2) pulse up to ±10 kV*High pulse output current up to ±40 A*High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)*6 programmable pulse rise times: 100 ps to 50 ns*8 programmable pulse widths: 1 ns to 100 ns*Optional pulse width extender increases pulse width up to 1.6 µs in 68 programmable steps*Fast measurement time, typically 0.2 s per pulse including one-point DC measurement between pulses*Efficient software for system control and waveform data management*The software can control automatic probers for fast measurement of complete wafers*High performance and high quality components
-
Product
High Voltage Inclined Plane And Erosion Tester
-
SCR ELEKTRONIKS have developed HIGH VOLTAGE INCLINED PLANE AND EROSION TESTER to carryout test specified in many standard to cover test method for the evaluation of the relative tracking and erosion resistance of insulating solid using liquid contaminant (ASTM D2303). Perform the Initial Tracking Voltage Test, Time to track Test, And Erosion Test as per selection.
-
Product
80-1000V AC Non-Contact Voltage Tester
5226
-
Peaceful Thriving Enterprise Co Ltd
This non-contact voltage tester, can be used to test the presence of AC voltage from 80V~1000V, no need of metallic conduction, easy to read by visual and audio indication. Locates breaks along live, insulated wires and power cords. Adjustable sensitivity allows tracing of wires behind walls, around switches or receptacle.
-
Product
Current And Voltage Input Sensors
-
Current input sensors monitor current from inverters in solar panel and wind turbine applications and turn the current into voltage which can be measured with an analog input type data acquisition module for analysis. Voltage Input Attenuators can be used to measure high voltages. Voltage Attenuators are designed for used in high-voltage applications. The current can be converted into +/-10 Vpp attenuated signal, so that a general electronic measuring device is able to read the signals.
-
Product
USB Preamplifier, 2 to 50 GHz
U7227F
Amplifier
The U7227F, 2 to 50 GHz USB preamplifier is designed to bring reliable gain and low noise figure to measurement systems improving the overall system performance and reduce systematic errors; a total solution to the X-Series signal analyzers to perform noise figure measurement
-
Product
200 Vdc External Voltage Bias Fixture
16065A
Test Fixture
Measure a DUT with up to +/-200 V DC bias and also measure axial/radial lead components
-
Product
PC Controlled Low Voltage Tester
Cablescan S32
-
The Cablescan S32, with a 32-board Expansion Cabinet, may be ordered with 1 to 32 low-voltage 128-point scanner boards. Fully loaded with scanner boards, this tester provides 4096 test points.
-
Product
Voltage Testers
-
Kyoritsu Electrical Instruments Works, Ltd.
AC and DC voltage tests up to 690V with LED Comply with the latest standards IEC 61243 and IEC 61010 Novel designLarge and bright LEDs: Values are visible in the dark placeErgonomic design fits in the hand Two functions are available in one model"Measurement without battery" and "Self Test (all LED on)" Test leads withstand harsh environments at low temperature Penlight (white LED) Auto-power ON/OFF Audible indication Variable test tips, 2mm or 4mm Probe protection cover can store the attachment of caps IP65 (IEC 60529)
-
Product
Work Area Voltage Detectors
-
*Warns of high voltage electric fields using WAVi technology - Work Area Voltage Indication*Visual and audible warning indicates the location of energized fields in a red-yellow-green sequence*Detectors communicate with each other within a mesh network*Remotely control detectors through the Lookout mobile app*Battery life of up to 500 hours in Monitor mode and up to 8 hours in Alert mode*Durable water-resistant housing
-
Product
AC /DC Withstand Voltage Tester 5KV/100mA
2672C
-
Shenzhen Chuangxin Instruments Co., Ltd.
*High voltage, large current, high accuracy.*Leakage current, testing time, continuous arbitrarily, well-adapted.*Synchronized display measuring value( time, voltage and current).*Can choose manual or remote control test*High voltage breakdown protection, sound and light alarm, safe and reliable *Easy operation, suitable for use in production line*DC output can test small capacitance, high-voltage silicon stack, reverse voltage of transistors
-
Product
Non-Contact Voltage Detector
VOLTCHEK
-
The VOLTCHEK is a variable non-contact voltage detector, A proximity device which detects the presence of an alternating electric or electromagnetic field. It is used by industry professionals for live or dead voltage determination of outdoor overhead or underground at URD test points. Firstly as a proximity device to determine live or dead situations and then as a touch device to verify the source has physically reached the zero AC field. This is the only equipment capable of testing all voltage from AC 415V to 765kV from a distance, beyond arcing zone.
-
Product
Contact Voltage Detectors
-
Shanghai Beha Electronics Co., Ltd.
The detector detects a high and extra high voltage in AC lines. An elongate insulation rod permits checking of high voltage circuits at safe distance for voltage.
-
Product
PXI High Voltage Multiplexer, 24-Channel
40-320A-101
Multiplexer Module
The 40-320A-101 is a single 24-channel MUX and is part of our 40-310/320A range of High Voltage Switching Modules which will hot switch up to 750V peak and cold switch up to 1000V peak in either general purpose relay (40-310) or multiplexer (40-320A) configurations.
-
Product
Insulating Boots (Gloves) Withstand Voltage Tester
-
Weshine Electric Manufacturing Co., Ltd
80KV Insulation Boots Withstand Current Leak Testing Withstand Voltage Tester
-
Product
High Voltage Differential Probes
-
High voltage differential probes provide high CMRR over a broad frequency range (up to 400 MHz) to simplify the measurement challenges found in noisy, high common-mode power electronics environments. The probe’s design is easy-to-use and enables safe, precise high voltage floating measurements.
-
Product
Solid State Voltage Injector
J2110A
-
While it is possible to obtain high quality injection transformers with bandwidths as wide as 1Hz to 5MHz or more, in some cases this is still insufficient for some tests. For example a typical heater control loop might have a bandwidth of less than 1Hz while some linear regulators and opamp circuits can have bandwidths of up to 100MHz or in some cases even higher. For these applications, a solid state injector can provide the necessary bandwidth. A solid state injector can perform at DC, while the upper frequency limit is dictated by the components selected and the printed circuit board material and layout. It is possible to obtain a solid state injector with a working range of DC – 200MHz, though above 50MHz the interconnection between the injector and the circuit being tested can become quite critical. It is essential that ripple from the injector power supply does not dramatically degrade the dynamic range or the signal to noise ratio of the measurement. The resulting plots are often much cleaner when using a solid state injector than with a transformer injector.
