Voltage Preamplifiers
-
Product
Voltage Detector
LV-1
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
Using conductive rubber tip, free from short circuit. With slip stopper for the safety use.
-
Product
Acoustic Emission Preamplifier
-
The Acoustic Emission Preamplifier is a instrument designed specifically for use with acoustic emission sensors, which is used to boost the signals and filter out any noise or interference. With its advanced technical features and robust design, the QingCheng Acoustic Emission Preamplifier is the perfect choice for professionals seeking a high-performance acoustic testing solution.
-
Product
Voltage Calibrators
-
Practical Instrument Electronics, Inc.
PIE has a voltage calibrator to fit your needs from the PIE 235 voltage and pH simulator to the advanced troubleshooting capabilities of the PIE 532 milliamp and voltage calibrator. The PIE 532 includes our patented Loop Diagnostic Technology! All the voltage/milliamp calibrators have fuse-less protection, rugged design and long battery life. With the PIE 535, source 4 to 20 milliamps or 10 to 50 milliamps into loop instruments and drive final control elements such as valves and actuators with up to 42 volts.
-
Product
NI-9224, ±10 V, 1 kS/s/ch, 24-Bit, Simultaneous Input, 8-Channel C Series Voltage Input Module
783862-01
Voltage Input Module
±10 V, 1 kS/s/ch, 24-Bit, Simultaneous Input, 8-Channel C Series Voltage Input Module - The NI‑9224 performs differential analog input. With channel‑to‑channel isolation, your entire system, including the device under test, is protected from harmful voltage spikes up to the isolation rating. The NI‑9224 is simultaneous sampling with two options for filtering a low-latency filter or a 50/60 Hz rejection filter. The low-latency filter enables users to use this module in industrial or control applications while getting better external noise rejection.
-
Product
High-Sensitivity Tri-Axial Accelerometer with Built-In Preamplifier
NP-7310
-
NP-7310 is the accelerometer with built-in preamplifier, and capable of tri–axial directions simultaneous measurement. It is suitable for the low frequency vibration measurement such as ground vibration or floor vibration while operating the machine. NP-7310 can be used with the sensor amplifier unit such as AU-2100, AU-2300 or PS-1300. Also, it is possible to input directly to the analyzer or recorder which the constant current amplifier is built-in such as the FFT Analyzer of DS-2000 series, DS-3000 series, CF-7200A, CF-9000 series or CF-3650/3850 series.
-
Product
Voltage Datalogger
S5021
-
Data logger is designed for record of voltage. Values are stored to a non volatile electronic memory. Data transfer to the personal computer for further analysis is performed via USB, RS232, GSM or Ethernet interface by means of a proper adapter.
-
Product
Preamplifier
-
Is designed for the amplification of measuring signals, e.g. weak signals of near field probes with high resolution.
-
Product
sbRIO-9201, Non-Enclosed, ±10 V, 500 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module
781113-01
Voltage Input Module
Non-Enclosed, ±10 V, 500 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module - The sbRIO‑9201 is an effective combination of channel count and speed at a low price for an economical multifunction system. In addition to the absolute protection from the isolation, the module features up to 100 V of overvoltage protection for errant signal connection or unexpected outputs to the individual channels. Non-enclosed modules are designed for OEM applications.
-
Product
Voltage Detectors
-
A safety tool or device used to determine the presence or absence of electrical voltage in a circuit, wire, or outlet.
-
Product
Voltage Testing
MicroDetect series
-
Hachmann Innovative Elektronik
Voltage detection simple and reliable with the MicroDetect line you get a type series of handy, exact and simply useable voltage detectors.
-
Product
Saluki SE4002 FET Input Preamplifier
-
The SE4002 is a low-noise, ultra-high input impedance preamplifier with excellent common-mode rejection. It is designed to work with any Saluki digital lock-in amplifier. The preamplifier minimizes noise and pickup in the connecting lines and reduces measurement time in noise-limited experiments.
-
Product
Voltage Probes
-
In addition to EMI measurement with LISNs (Line Impedance Stabilisation Networks, Artificial Mains Networks), Probes are used for Terminal or Line voltage measurement.
-
-
Product
Electrical Tester For Voltage
PDT35
-
Automatically Selects VAC, VDC, or Continuity TestComplies with EN 61010-1 For Use in CATIII 600 V Environments1999 Count LCD DisplayAuto Power On/OffHigh Input Impedance -- 400 kVoltage AC: Max Range 600 V, Accuracy +/- 1.5%Voltage DC: Max Range 600 V, Accuracy +/- 3.0%Continuity TestAccessories Included: Test Leads, 2 'AA' BatteriesDimensions: 8.46' H x 2.83' W x 1.44' DWeight: 8.29 oz.Sold as : Unit
-
Product
High Voltage Probe
HVP-15HF
-
*MAX.VOLTAGE:15KV DC.*BANDWIDTH:DC~50MHz.*DIVISION RATIO:X1000.*SIGNAL/NOISE:>60dB(1KHz)
-
Product
Voltage And Current Calibrator
-
Precision Mastech Enterprises Co.
A precision instrument designed to generate (source) and measure precise electrical signals.
-
Product
AC Voltage Detector
-
Triplett Test Equipment & Tools
high performance AC Voltage detector with adjustable sensitivity that has a wide measurement range of 25 to 1000ACV, Dual Color Tip to indicate low/high voltage, built-in flashlight and durable overmold. The high sensitivity allows it to detect low voltage AC wiring commonly found in doorbell circuits, thermostats, control circuits, and video surveillance camera power. The Sniff-It 3 is designed for industrial applications with its impact and drop resistance in a sleek ergonomic design, and the easy to use thumb wheel helps dial-in detection range. Includes (2) AAA batteries. CAT III safety rating.
-
Product
High Voltage Pulse
-
For thicker coatings it has fully adjustable output voltage from 5 kilovolt to 25 kilovolts. For very demanding conditions, a sensitivity switch offers additional control.
-
Product
AC Voltage Sensors
-
Continuously monitor single or three-phase power lines for over or under voltage conditions with DARE?s AC voltage sensors, voltage monitors, and voltage sensing relays. DARE?s complete line of AC Voltage Sensors will protect system equipment and circuitry from voltage that is hazardous or unsuitable for operation.
-
Product
High Voltage Probe
HVP-40M
-
*DC 40KV CAT II Pollution 2*600MΩ Impedance*25KV ± 2%, 40KV ± 3%*T.C. 200 ppm/oC*Positive Polarity only.*Resolution 1KV*Need not power.*CE, TUV GS, UL, CUL, IEC1010
-
Product
C-Band Single Channel Pre-Amplifier EDFA (SPA)
HSA4300 (With SNMP)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HSA4300 series is a low noise pre-EDFA which designed specifically for single wavelength optic transmission system. It is installed in the front of optical receiver, used for improving the receiving sensitivity of the optical receiver, and extending the signal transmission distance.
-
Product
Voltage & Continuity Tester
ET250
-
The ET250 voltage and continuity tester incorporates an LCD display, measures AC/DC voltage up to 600V and can test GFCI protected circuits. Both voltage testers have a tough meter design and are rated CAT IV 600V for safety.
-
Product
Voltage Continuity Testers
-
Built tough for use in industrial and commercial environments, measures voltage range up to 1000 V AC and 1200 V DC (2100-Gamma only). Designed with reinforced components for dependable performance.
-
Product
Voltage Tester, LED
72-9395
-
*Easy to use voltage tester designed for the professional user*Waterproof and rugged making it ideal for nearly all situations*Continuity test*690V max*Short circuit detection*Automatic range selection*Single lead voltage detection*Phase rotation test (50-60Hz)*Polarity detection*Built-in LED light*Rubberised grip*12 month limited warranty *view Terms & Conditions for details
-
Product
Test Probe Connector, High Voltage, Voltage, 3 %
72-6530
-
The 72-6530 is a high voltage Testy Probe with built-in meter measures voltages up to 40kVDC.
-
Product
High Voltage Tester
-
Aarohi Embedded Systems Pvt. Ltd
AAROHI make high voltage tester is specially designed to test induction & submersible motors with cutting edge technology.High Voltage Tester is manufactured as per the International set standards and regulations. This High Voltage Testers are available in AC and DC types and are used for testing HV cables after installation and repair for ensuring efficient performance. It also indicates voltage withstands level and current leakage level of the cable during the testing period.
-
Product
Surge Voltage Generator
SSG 2100
-
Cable fault location with the BAUR SSG 2100. Surge voltage generators are used for pre-location and pinpointing of high- and low-resistive as well as intermittent faults in power cables. The energy stored in a high-voltage capacitor is released at regular intervals or as DC voltage. The thus generated acoustic signal at the fault position can be recorded with a ground microphone and a universal receiver.* High surge voltage up to 32 kV* Continuously adjustable voltage* Voltage monitoring through kV meters with 3 measuring ranges* Automatic discharge unit
-
Product
Voltage Tester
-
*Simple and user friendly*Check 1.2V - 230V AC & 12V DC directly*Check ground line and phase line and breakpoint of the AC directly*No battery is required
-
Product
Surge Voltage Generator
SSG 1500
-
Cable fault location with the BAUR SSG 1500. Surge voltage generators are used for pre-location and pinpointing of high- and low-resistive as well as intermittent faults in power cables. The energy stored in a high-voltage capacitor is released at regular intervals or as DC voltage. The thus generated acoustic signal at the fault position can be recorded with a ground microphone and a universal receiver.* High surge voltage up to 32 kV* Continuously adjustable voltage* Voltage monitoring through kV meters with 3 measuring ranges* Automatic discharge unit
-
Product
Differential Voltage Probes
DP150/DP200pro
-
The DP differential isolation probes are an important accessory for any laboratory involved in power electronics and high voltage systems. These probes allow isolated and floating measurements with any oscilloscope or data recorder, whilst the oscilloscope can remain grounded. Using a DP150 or DP200pro probe, differential and floating measurements can be made on a variety of ac power systems like 230V/110V ac input power supplies, chopped and switching power supplies, thyristor controllers, variable speed motor drives (PWM signals), motor inrush current and measurement across current shunts. The isolated input is made via two 4mm/banana safety sockets. The BNC output allows easy connection to an oscilloscope. The DP probes can be powered from a 9V battery or external power supply.
