Voltage Preamplifiers
-
product
High Voltage DC Lab Power Supplies 300V-5000V Output for Research Labs / Capacitor Testing – 300, 600, 1000, 3000, 5000V
- 19” Rack Adaptable- Laboratory Bench Unit- Digital Output Metering- Constant Voltage Current Limit Type Character- Micro Switch Provided for Protection against Shock- 3U High (133 mm)- Power Saving Thyristor Preregulator Technique
-
product
High Voltage Film Capacitors
High Voltage Pulse Capacitors, High Voltage Energy Discharge Capacitors, High Voltage Filter Capacitors and Customized High Voltage Capacitors
-
product
Dualite High and Low Voltage Tester
22400
Two circuit testers in one - troubleshoot both primary and secondary circuits. Use as a primary circuit tester on 6 and 12 volt circuits or on secondary or high voltage circuits to check out spark plugs. 48" lead wire.
-
product
High Voltage Diode Assemblies
High voltage diode assemblies are built by adding diodes in series to yield a higher peak inverse voltage. For example, if each diode is rated for 1200 peak inverse voltage (PIV), then six diodes in series would have a total peak inverse voltage of 7200 PIV. The detailed circuit is shown below.
-
product
High Voltage Probe, 100:1, 3.7 KVpk, 500 MHz
10076C
The Keysight 10076C 3.7 kVpk, 100:1 passive probe gives you the voltage and bandwidth you need for making high-voltage measurements. Its compact design makes it easier to probe today's small power electronics components, and its rugged construction means it can withstand rough handling without breaking.
-
product
Clamping Voltage Tester
MIG0603CLV2
The MIG0603CLV2 is a generator for clamping voltage testing of varistors. It has circuits with four different source impedances and up to 15 different measurement ranges. The instrument is used to perform varistor clamping voltage tests on up to 1000 V varistor types. The test impulse is a 8/20µs current waveform up to 500A which is maintained over the entire load range.
-
product
Preamplifiers
LNA Series
Low noise amplifier with 12.5 dB of gain covering the nominal frequency range 1 MHz to 3 GHz and can be used in the range from 200 kHz to 4 GHz. With its high gain and low noise figure, it will significantly increase the sensitivity of virtually all spectrum analyzers and other RF measuring instruments. All measuring instruments have a 'noise figure', which is a measure of how good the instrument is at measuring low level signals, the lower this figure, the better, although the lowest signal level will still be governed by the measurement bandwidth. A typical spectrum analyzer may have a noise figure of 20 dB or more, whereas a typical receiver may have a noise figure of 10 dB. The preamplifier has a noise figure of typically 4 dB, significantly enhancing the low level performance of such instruments, enabling signals that were previously masked by noise to be seen.
-
product
(70×90×15mm) Full Function Single Channel MSA Compact Pre-Amplifier EDFA Module
SPA4300-FM02
Hangzhou Huatai Optic Tech. Co., Ltd.
SPA4300-FM02 is a full-function optical Pre-Amplifier with digital control electronics, adopts 70×90×15mm MSA compact package. It is featured with high reliability, superior optical performance and compact reasonable configuration by Industrial standard, creating the most flexible and variable low-cost amplifier in the market. This module is suitable for multiple network application, especially the application that requires 40GB/S transmission speed.
-
product
Stand Alone Low Voltage Tester
Model 64×2
Internal Memory: 8 program locations without test point labels or 2 program locations with test point labels. Removable Memory: 16 program locations without test point labels, or 4 program locations with test point labels.
-
product
HIGH VOLTAGE SCR CONTROLLED POWER SUPPLY
xPS Series
High Voltage SCR Controlled Power Supply, P/N 18278PS Power Rating: 350 KW. Input: 480 VAC, 3 PH, 60 Hz Output: 0 to 5000 VDC, 70 Amps max Ripple: 2 % approximately at maximum rated voltage Configuration: 12 pulse externally SCR controlled rectifier system Protection Devices: Input contactors Overload relay shutoff Input surge suppressor Thermal switches Output current limiting resistor (made with 5 Ohm Kanthal heating element) Emergency power shutoff Cooling: Each 6 pulse rectifier assembly is cooled by three 10” fans Interface: 4/20 ma converter interface for output voltage and output current to SCR controller. Enclosure: The overall dimension of the unit is (78”H x 38”W x 53”D). It is comprised of two separate enclosures each with dimensions of (78” H x 38” W x 26” D) which are integrated together to form a single enclosure. Each half enclosure has one 6 pulse transformer and one 6 pulse high voltage rectifier. Weight: Approx. 5000 lbs. SCR Controller: The 12 pulse SCR controller is supplied by the customer. We were responsible for the 12 pulses Transformer and 12 pulses Rectifier section. Portability: Unit can be lifted up with a fork lift. It can also be moved around with a 5000 lb pallet jack. Transformer: Two 200 KVA transformers are used to step 480 VAC to 3750 VAC each in a 12 pulse configuration Rectifiers: Two 6 pulse rectifier assemblies capable for 5000 VDC and 60 Amps output were used. The high voltage rectifier assemblies are isolated and protected in a fiberglass plenum within the enclosure. Blocking Diode: Each diode of the 6 pulse rectifier consists of 10 diodes in series to offer a blocking voltage of 12000 V (PIV)
-
product
High Voltage Impulse Test Set Up
We are renowned as the foremost manufacturer and exporter of High Voltage Impulse Test Set Up. This testing equipment is demanded in electrical, power generation and engineering sector. It is incorporated with fiber optic isolated digitizers to test various types of transformers. We utilize excellent grade raw materials to engineer and develop this High Voltage Impulse Test Set Up in accordance with industry standards. Our clients can get this equipment from us at competitive price.
-
product
DC to DC Voltage Regulator
HVDR-15
The HVDR-15 is a high efficiency, high voltage step down DC to DC voltage regulator. Input voltage can be as high as 110VDC. Up to three output voltages can be pre-configured to allow up to 1A or 3A of output current. The HVDR-15 features over voltage, over current, and over temperature protection. It is offered in one, two, or three output voltage versions making it a very efficient and flexible platform for many applications.
-
product
Ultra-low Noise High Voltage Amplifier
WMA-200
The Falco Systems WMA-200 model is a high quality, high voltage, linear laboratory amplifier optimized for experiments requiring world-class, ultra-low output noise. The excellent noise performance, combined with the wide bandwidth and large voltage range make this amplifier the preferred choice for the most demanding precision positioning systems. The amplifier will routinely enable sub-atomic positioning resolution with piezo positioning systems and MEMS devices. Two WMA-200 amplifiers and a WMA-IB-LN phase inverter - buffer can be used to double the output voltage.
-
product
Automatic High Voltage Wire Harness Testers
Automatic high voltage wire harness testers are used in a variety of industries, such as aerospace and defence through to rail, and are used to test any equipment which contains a high number of electrical wires, or active components ensuring these pass specified test criteria at the sub-assembly and final stages of construction. These systems ensure the wiring and components are 100% compliant and undamaged, recording every test measurement and aiding diagnosis of detected faults.
-
product
High Voltage 50 Ω Pulse Generator
TLP-3010C
High Power Pulse Instruments GmbH
*Wafer and package level TLP/VF-TLP/HMM testing*Ultra fast 50 Ω high voltage pulse output with typical 100 ps rise time*Built-in HMM (IEC 61000-4-2) pulse up to ±8 kV*High pulse output current up to ±30 A*High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)*6 programmable pulse rise times: 100 ps to 50 ns*8 programmable pulse widths: 1 ns to 100 ns*Optional pulse width extender increases pulse width up to 1.6 µs in 68 programmable steps*Fast measurement time, typically 0.2 s per pulse including one-point DC measurement between pulses*Efficient software for system control and waveform data management*The software can control automatic probers for fast measurement of complete wafers*High performance and high quality components
-
product
VOLTAGE TRANSFORMERS
Designing & manufacturing a range of high quality, voltage transformers in three different frame sizes for both measuring and protection duties. Transformers which are designed to comply with the requirements of IEC 61869-3 or other international standards as required can be supplied to satisfy most Low Voltage applications.
-
product
High Voltage Ammeter Recorder
GF2018
Beijing GFUVE Electronics Co.,Ltd.
GF2018 is the newest version of the wireless primary current sensor. Rational design and 433M transmit technology makes the recording more stable and accuracy.
-
product
Voltage Protection ICs
ST’s voltage protection devices prevent external overvoltage (or undervoltage) peaks from damaging circuitry. They are commonly implemented on the power charging patch of portable devices to prevent USB or AC charger power failure. ST’s devices offer the advantage of very precise voltage thresholds, so that the protection is activated accurately, and without fail.
-
product
Voltage Pulse Generator
LSG-65C
Shanghai Sanki Electronic Industries Co., Ltd.
The waveform parameters of the voltage pulse generator LSG-65C fully meet the requirements of IEC60065 and GB8898; the pulse voltage output of up to 10kV can meet the requirements of different test levels of users; the self-developed high-voltage electronic switch is adopted , which has high stability, low noise and long service life. Long; digital display mode, intuitive and easy to operate.
-
product
Voltage Detector
KEW 5711
Kyoritsu Electrical Instruments Works, Ltd.
Senses AC voltage through insulation. Buzzer sounds and tip glows upon ac voltage detection. Powerful flashlight. Dual range (Hi/ Lo) sensitivity. Ready to use without power-on. Designed to meet IEC61010-1.
-
product
Low Voltage Wet Sponge
Operates on a single 9-volt alkaline battery. Unit output voltage is 67.5 volts DC. This voltage makes the detector highly sensitive and accurate. Compact and light weight with no bulky battery packs allowing for non- destructive inspection of paints, epoxy paints and coatings 1-20 Mils.
-
product
Triple Alarm CAT IV Non-Contact Voltage Detector with Flashlight
FLIR VP50-2
The FLIR VP50-2 is a durable, CAT IV-rated non-contact voltage detector featuring light, vibration, and beeper feedback alarms and a powerful LED flashlight. Use the VP50-2 to reliably check if an AC circuit is live before beginning work; detect voltage on exposed conducting parts or through insulation; identify live wires within electrical panels, switches, and outlets; or trace live wires and map circuits. With an ergonomic and drop-tested design, the FLIR VP50-2 is the right choice for professionals performing field troubleshooting and verification of electrical installations within residential, commercial, and industrial buildings.
-
product
Clamping Voltage Tester
MIG0603CLV1
The MIG0603CLV1 is a generator for testing varistors. It has circuits with three different source impedances and up to 11 different measurement ranges. The instrument is used to perform varistor clamping voltage tests on up to 1000 V varistor types. The test impulse is a 8/20µs current waveform up to 200A which is maintained over the entire load range.
-
product
High Voltage Pulse Generators
Berkeley Nucleonics Corporation
Designed to provide precision control over the output waveform to enable process optimization for research and industrial customers.
-
product
High Voltage Test & Measurement
High-voltage (HV) testing utilizes the phenomena in electrical insulations under the influence of the electric field for the definition of test procedures and acceptance criteria.
-
product
3 In 1 Metal Voltage Stud Detector
NT-6352
Combined unit to accurately detect live or dead electricity cables, water or gas pipes and wooden studs or battens.LED & buzzer indicators.Depth penetration 18~20mm.Using precision screwdriver for easy unit sensitivity adjustment.Power source: NEDA1604/6F22 (9V) x 1pcs(Not included).Size: 178 x 120 x 34.7mm.
-
product
High Voltage Testers
HV Test, which is also known as Hipot Test – short form of high potential – is used to test the insulation quality of the auxiliary circuit of circuit breakers. The HV Test is useful in finding damaged insulation, stray conductive materials around the conductors, and problems due to terminal spacing and tolerance errors in cables.
-
product
PXI/PXIe High Voltage Multiplexer, Hex 7-Channel, 1-Pole
42-321-103-HI
The 40-321-103-HI (PXI) and 42-321-103-HI (PXIe) are hex 7-channel 1-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
product
Clamp type AC Current Sensor／with DC Voltage Output
ACT-50H
MULTI MEASURING INSTRUMENTS Co., Ltd.
*For current measurements of the control board*AC 1A～50A*DC 5V full scale output
-
product
Stand Alone Low Voltage Tester
TestMate 256
The TestMate continuity tester features a universal interface fixture that accommodates adapter cards for quick changes in harness setups. Adapters can be exchanged in seconds to adapt quickly to any of a variety of wire-harness/cable connectors.
