Force Gauges
measure push and pull.
-
Product
Large Calibre Barrel Bore Gauge System
BG20
-
Aeronautical & General Instruments Ltd.
The BG20 has been specifically designed to modernise and improve the inspection routines of large calibre barrels. A two-point measuring head is supported in the barrel or chamber by a clear disk which facilitates the angular alignment of the head and the location of a suspected defect.
-
Product
48-Channel High Performance Strain Gauge Measurement Instrument
EX1629
-
48-Channel High Performance Strain Gauge Measurement InstrumentSupports quarter-bridge (120, 350Ω or user defined), half-bridge or full-bridge24-bit ADCs, sampling rates up to 25 kSa/sBuilt in programmable differential excitation -8V to 8VBuilt in selectable bridge completionConfigure signal conditioning excitation and bridge completion on a per channel basisSimple, low-cost wiring using RJ-45 telecom connectorsSupports TEDS for easy transducer detection and setupRJ-45 input connector reduces setup cost and timeBuilt in self-calibration and shunt calibrationSupports voltage, ratiometric and linear measurements other than strain measurements.
-
Product
Thermocouple Vacuum Gauge Tubes
DV-6 Series for Medium Vacuum
-
Teledyne Hastings, manufacturer of the original DV-4, DV-5, and DV-6 thermocouple vacuum gauge tubes, produces vacuum measurement equipment with exceptional stability, accuracy, and reliability under the most demanding conditions.The Teledyne Hastings’ DV-6 series thermocouple vacuum gauge tube acts as a localized sensor which is then paired with a selection of meters or controllers to provide reliable, cost-effective measurements in diverse applications. The robust sensor gauge tube is easily installed into vacuum systems and when properly excited, generates a thermoelectric voltage to provide a vacuum pressure measurement based on gas density. The DV-6 thermocouple vacuum gauge tube fully compensates for temperature and rate of temperature change.Thermocouple gauge tubes are calibrated on vacuum systems that contain N2 or Air, but can be used with other gases. Additionally, thermocouple gauges and their controllers can be recalibrated when a replacement thermocouple gauge tube is installed, following instructions in the manual. However, our DB-20 reference tube is available to confirm meter/controller performance. A complete line of installation accessories are also available to simplify the integration of our thermocouple gauge tubes into a variety of vacuum systems. Our goal is to provide “one less thing to worry about”, when performance matters! With a wide range of meter, fitting, relay and output options, the DV-6 series provides a reliable pressure measurement in numerous industries and applications.
-
Product
Verification Of Maximum Withdrawal Force Test Apparatus
IEC60884 FIG 18
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 FIG 18 verification of maximum withdrawal force test apparatusThis device complies with the requirements of GB 189.1-2008 Figure 18/19, IEC884 Figure 18/19, VDE0620, etc. It is suitable for checking the maximum force required to pull the plug out of the socket and the single pole pin pulled out from the socket assembly. Whether the minimum force required is within the range specified by
-
Product
Atomic Force Microscope
DriveAFM
-
The DriveAFM is Nanosurf’s novel flagship AFM platform: a tip-scanning atomic force microscope (AFM) that combines, for the first time, several capabilities in one instrument to enable novel measurements in materials and life sciences.
-
Product
Application Gauging
-
Bowers Group offers a range of both standard and bespoke measurement solutions for a variety of gauging applications. As the world’s leading bore gauge manufacturer, our application heads can be fitted directly onto our XT range of internal micrometers to create a flexible, modular measuring system. Whether you’re measuring threads, grooves, splines, sphericals, or deep holes, we have a standard solution to suit. If you’re looking for something completely bespoke, our team has the skills and expertise to solve your measurement problem.
-
Product
Wall Measurement Thickness Gauge Wall Thickness Test Instrument
HS160
-
Shenzhen Chuangxin Instruments Co., Ltd.
HS160 Wall measurement thickness gauge, wall thickness measuring equipment apply to measure the thickness of all kinds of material, through which the ultrasonic wave can propagate at a constant speed and can get reflection from the back. This instrument can be used for a variety of plate and all kinds of machining parts for accurate measurement. Another important function of this gauge is to monitor all kinds of pipelines and pressure vessels used in the production equipment, monitoring their degree of corroded thinning during the using process. It's widely used in petroleum, chemical industry, metallurgy, shipbuilding, aviation, aerospace and other fields.
-
Product
Load Cells & Force Transducers
-
BLH and Nobel Weighing Systems offer a wide variety of load cells and force transducers, ranging from the unique KIS load cell and weigh module to the VPG transducers range of products. Our many years of experience, our state-of-the-art instruments, and the exceptionally broad range of components that go into our systems allow us to deliver high-quality solutions tailored to your needs.
-
Product
3-Component Quartz Force Links
261 Series
-
Three-component force links eliminate the preload requirement of 3-component quartz force ring sensors, and offers a convenient, 4-screw hole mounting plate on each side end the sensor. Quartz 3-component force links are constructed by installing a 3-component force ring sensor, under preload, between two mounting plates.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type C, Ø1.50mm, 155gf
K100-C150155-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style C, Tip Diameter Ø1.50mm, Spring force 155gf, Steel with Gold Plating.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type Q, Ø0.80mm, 230gf
K100-Q080230-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style Q, Tip Diameter Ø0.80mm, Spring force 230gf, Steel with Gold Plating.
-
Product
CORROSION GAUGE
MMX-7
-
The MMX-7 has all features of the MX & MMX gauges with some additional features and advantages. Selectable Large Digits and B-Scan display options. An internal data logger that stores a total of 12,000 readings and waveforms, 64 user custom definable setups, selectable transducer table for improved linearity, thru paint mode with the single press of a button, multiple calibration and material selection options, and selectable low, medium or high gain options. This is all nicely packaged in a very mini portable aluminum extrusion for extra durability and portability! The MVX/PVXview or Java-based PC software makes this thing a complete kit and then some! 2-year limited warranty.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type K, Ø1.50mm, 155gf
K100-K150155-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style K, Tip Diameter Ø1.50mm, Spring force 155gf, Steel with Gold Plating.
-
Product
Standard Flexiforce Sensors for Force Measurement
FlexiForce
-
FlexiForce force sensors are ultra-thin and flexible printed circuits, which can be easily integrated into force measurement applications. These sensors are available for purchase in our online store.
-
Product
Miniature Quartz Force Sensors
-
Often the test engineer will try to take low level measurements with a sensors not rated for these low levels. Due to insufficient sensitivity the resulting data may be noisy, hard to analyze or unusable. Using the appropriately sized and ranged PCB Miniature Quartz Force Sensor solves the problem and gives reliable data at a Low Amplitude level. The miniature sensor configuration permits low-amplitude, dynamic compression, tension, and impact force measurements.
-
Product
Gauge Pressure Transmitters
-
The Gauge pressure transmitter portfolio from ABB offers a broad variety of communication possibilities. Another highlight of our sensors is the measurement accuracy up to 0.025 %.
-
Product
Universal SOIC ZIF (Zero-Insertion-Force) Test Socket
Series 547
-
Universal SOIC Zero Insertion Force Test Socket. Devices with up to 44 pins can be inserted without bending or otherwise damaging the legs, since no force is required to either insert or remove the component from the socket. Accepts SOIC gull-wing and J-lead devices, up to 44 pins on .050 [1.27] lead pitch, body widths from .150 to .600 [3.81 to 15.24].
-
Product
Coating Thickness Gauges
-
Coating thickness gauge is a kind of portable measuring instrument, can take fast, intact, precise measurement of coating thickness. It can not only be used in engineering field, laboratories, but also meet the demand of multiple measuring by using different probes. It is used widely in manufacturing, metal processing industry, chemical industry, commodity inspection field, etc. As an essential instrument in material protection industry.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type E, Ø1.50mm, 305gf
K100-E150305-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style E, Tip Diameter Ø1.50mm, Spring force 305gf, Steel with Gold Plating.
-
Product
Pedal Force Load Cells
-
Pedal Effort Sensors are designed to measure load applied to the brake, accelerator, and clutch pedals during acceleration, deceleration, and transmission shift events. The units are compact and light weight, making them easy to install and remove.
-
Product
ThermalAir Desktop Series Temperature Forcing System
ThermalAir TA-1000A Desktop System
-
The ThermalAir TA-1000 high capacity thermal air stream system is used for temperature testing, fast thermal cycling, and device temperature characterization of components, hybrids, modules, PCBs, and other electronic and non-electronic assemblies at precise temperature from -25°C to +200°C.
-
Product
Tide Gauge
TideMaster
-
The Tidemaster is the cost-effective way to accurately record water height, with the added option of gathering meteorological data using its ultrasonic wind speed and direction sensor.
-
Product
Combination Gauges
-
Global Digital Instruments, LLC
GDI offers a variety of combination gauges including a Dual Gauge which can monitor battery status, fuel level, or voltage and an hour meter as well as a Dual Gauge to monitor battery life and hours with a battery shut down feature to extend the life of your equipment.
-
Product
Magnetic Float Type Liquid Level Gauge
HR9210
-
HighReach Measuring & Controlling System Co.,Ltd
The HR9210 magnetic float type liquid level gauge is a measuring instrument that reflects the measured liquid level or interface by the magnetic float as the sensing element and through the coupling of the magnetic float and the magnetic body in the display color strip.
-
Product
Full Bridge Thin Beam Force Sensors
TBS SERIES
-
The TBS Series thin beam force sensors many different parameters found in medical instrumentation, home appliances, process control, robotics, and automotive are exceptionally suited for small load measurements. They are designed to measure and many other high volume applications. A specially developed integrated strain gage includes all balancing, compensating and conductive elements and is laminated to the beam to provide excellent stability and reliability.
-
Product
One-Touch, Strain Gauge Extensometers
SSG-H Series
-
The SSG-H series of strain gauge extensometers are compliant with ISO, JIS, and ASTM tensile test standards for hard plastics and metal materials Featuring a wide elongation measurement range with the ability to measure using small gauge lengths, these lightweight, clip-on strain gauge extensometers attach to both rod and flat plate specimens.
-
Product
Vacuum Pressure Gauge
EEPV511
-
Test vacuum accessories and emission control devices such as EGR valves canister purge systems, air switching and divert valves, vacuum delay and check valves, heater and A/C controls and cruise control systemsMulticolor gauge face with scales of inch, Hg, psi, negative kPa and positive kPa
-
Product
View Gauges
-
These view gauges are designed for multiple uses and are made for insertion, into els, tees, or other N.P.T. fittings and are easily installed and removed with a wrench. These rugged units are turned from solid hexagon material and come with a clear glass window firmly held between two gaskets.
-
Product
Deep-Bore/Spherical Diameter Gauging
XT Spherical
-
• 2 point (ovality) available from 3mm, 3 point available from 6mm• 6-300mm range, 300-500mm XT500 System• Guide sleeves available, 2 point to maintain centralisation, 3 point to protect the head/bore• Allows for misalignment in bore• XT, Ultima• Ease of use for operator• Interchangeable with standard heads• Blind Bore option available
-
Product
Medium Accuracy Vacuum Gauge
-
The SVP Medium Accuracy Vacuum Gauge is based on the Hastings 0-1,000 mtorr (micron) meter assembly. SVP has chosen Hastings instruments for their quality and dependability when used in close proximity to high voltage.
