-
Product
Power Amplifier (DC Powered)
-
RF Lambda’s DC solid state power amplifiers (PA) are used in a variety of applications and offer high output power, wide band operation and good linearity. Hermetically sealed options are available upon request.
-
Product
C & L-Band Separate Raman Fiber Amplifier
RFA7000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
Product
Standard CW Amplifiers
-
The BT-AlphaA-CW series is a range of classAB RF power amplifiers covering the 10kHz to1MHz frequency range. Rugged, solid-state design - high reliability. Extremely high phase and amplitude stability. High linearity. In-Built Protection. Very fast blanking. Capable of pulsed operation. Competitively priced. Suitable for CW radar, communications, HF/VHF jamming, particle accelerator applications/plasma systems, plasma, RF heating and other scientific applications.
-
Product
Solid State RF and Microwave Switches
-
The Solid State RF and Microwave Switches have the following advantages over mechanical switches; long operating life, fast switching time, low power consumption and small size. Mechanical RF and Microwave Switches usually have lower insertion loss, higher isolation and higher RF power handling capability. However, because of the advantages mentioned above, Solid State RF and Microwave Switches are to prefer if very low insertion loss and/or very high isolation is not needed.
-
Product
Amplifiers & Signal Processors
-
Power for Core Technology Group Signal Chain ProductsFlexible bi-polar voltage converter using low cost connectorsDriving multiple devicesIndustrial +/- 10 volt power source
-
Product
Saluki SE1022 DSP Lock-In Amplifier
-
SE1022 Digital Lock-in Amplifier provides an excellent performance within its bandwidth from 1 mHz to 102 kHz. With the advantage of the latest digital signal processing technology and high-precision 24-bit ADC, SE1022 can easily detect the phase and the magnitude of weak signals overwhelmed by various large noises. The performance of SE1022 is as good as other lock-in amplifiers brands, even better in some certain parameters, such as measurement accuracy, SNR, dynamic reserve. Otherwise, SE1022 integrates some special functions like multiple harmonic measurement and FFT, which meets the needs of scientific research and industrial application well.* Saluki SE1022 can be comparable to SRS SR830, even better and more stable.
-
Product
Variable Gain High Speed Linear Amplifier
F30PV
-
The F30PV is a very fast general purpose linear amplifier having a variable amplification of 0-10 times and capable of bipolar voltage output of ±35V. Any functiongenerator or arbitrary waveform generatoror any othe signal source can be used as an input device. The amplifier's output is linear from DC up to ca 10 megahertz range. It can be used in a wide range of high speed applications.
-
Product
LXI 50Ω Microwave Transfer Switch
60-808-210-006
-
These LXI (Ethernet-controlled) Microwave Transfer Switches are suitable for routing 50 Ω signals up to 50 GHz. With up to 16 switch banks, they are ideal for constructing complex microwave switching systems for many applications. Connection is by front panel mounted SMA. SMA 2.9 or SMA 2.4 connectors.
-
Product
Instrumentation Amplifiers
HIGH-POWER RADIO FREQUENCY (RF) AND MICROWAVE AMPLIFIERS, TWTA AND SOLID STATE
-
Communications & Power Industries
Electromagnetic compatibility (EMC) high-intensity radiated field (HIRF) testing, military testing, electronic warfare simulation and scientific applications are based on the same switched-mode power supply technology as its rugged amplifiers. As a result, these instrumentation amplifiers have all the same performance and reliability advantages as the rugged product line, but have been neatly re-packaged into compact, lightweight and affordable rack-mountable units more suitable for less demanding physical environments. CPI TMD's new modular design (the PTCM range) has many user benefits, including advanced self-diagnostics, ethernet interfaces, remote management, VSWR protection and plug and play field replaceable power supplies.
-
Product
Dual Channel HV Amplifier with Phase Inverter
A400DI
-
This unit contains two independent A400 amplifiers that share common ground reference and power supply. Please see A400 page for technical details.It features also a low voltage phase inverter that inverts the signal applied to the input of channel 1. The resulting signal can then be connected to the input of channel 2 by means of a short BNC cable (supplied). As a result the two outputs operate in counter-phase. Connecting a load between the outputs effectively doubles the amplitude range. Please note that the load cannot have any connection to ground.
-
Product
Lock-in Amplifier
Signaloc
-
Designed for use in Hinds’ Exicor Systems the Signaloc is now availaible for anyone who can use a dual-phase, analog, single frequency lock-in amplifier.
-
Product
Amplified Photodetectors
-
Hinds Instruments' photodetector modules are specifically designed for use with high frequency optical signals including those generated in Photoelastic Modulator (PEM) applications.
-
Product
Amplifiers
-
We have designed and manufactured amplifiers using all major semiconductor materials, LDMOS, GaN, GaAs, and InP, to produce narrow, wideband, and pulse, receive and transmit amplifiers from 1 MHz to 220 GHz and power levels from mW to over 10 kW.
-
Product
Transimpedance Amplifiers
-
Current-to-Voltage Amplifier for use with Photodiode-Based Detectors. Transimpedance Amplifiers, Standalone Devices with Data Acquisition as well as Display Function (Optometer). Log/Lin Switching Amplifiers, etc.
-
Product
110GHz Microwave cable assembly
MWX001
-
Low insertion loss and excellent phase stability against bending up to 110GHz. High quality signal transmission with excellent flexibility and form-sustainability.
-
Product
Single and Multi-Function High Power Amplifiers
-
This lab unit is capable of a power output of 30 Watts and operates at a frequency range from 1200 MHz to 1400 MHz. The compact and rugged design of this system is ideal for bench-top testing and many other applications where both simplicity and portability are required.
-
Product
2 Channel Microphone Power Supply and Conditioning Amplifier
SoundConnect 2 mic power supply
-
SoundConnect 2 is a rugged 2-channel USB controlled microphone power supply and conditioning amplifier.
-
Product
4-Quadrant Power Amplifier PHIL
PAV15000
-
PAV Series phil 4-quadrant power amplifier is based on linear power amplifier technology and integrated advanced technical performance and rich functions.
-
Product
Amplifiers
-
The amplifier is one of the most important components in a pulse processing system for applications in counting, timing, or pulse amplitude (energy) spectroscopy, providing the pulse-shaping controls needed to optimize the performance of the analog electronics.
-
Product
Distribution Amplifiers
-
The Quartzlock range of distribution amplifiers are intended for use when multiple outputs from a single frequency standard/generator are required. This may be encountered in engineering labs, national standards labs, research and development, calibration labs and production. This is vital for the distribution of signals from other precision frequency standards like Hydrogen Masers, Cesium oscillators. For a technical discussion about distribution amplifiers go here or select a product range below.
-
Product
PNA Microwave Network Analyzer
N5224B
-
Meet your toughest measurement challenges with the highest performing microwave network analyzer in the industry Measure S-parameters with the smallest uncertainty and highest stability Efficiently characterize active components with applications that simplify setups Meet your specific budget and measurement needs by customizing to just the right level of performance Accelerate insight into component behavior using a multi-touch display and intuitive user interface Every spec verified, adjustments included Lock in support & peak performance from the start
-
Product
RF / Microwave / mmW Components
-
CAES maintains a broad portfolio of commercial and military grade RF, Microwave and Millimeter wave components that remain at the forefront of military and aerospace systems. Products are available as standard catalog offerings, and many can be uniquely customized to meet your exact performance specifications.
-
Product
Microwave Modules And Assemblies
-
These products integrate microwave components such as attenuators, switches, oscillators, amplifiers, filters, couplers and mixers, with the associated electronic circuitry, into one overall assembly.
-
Product
Amplifier Modules Band Specific
-
Modules are usually smaller and are usually part of systems. You supply your own DC voltage, make the connections and supply your own DC supply. Modules are available with or without heatsinks and fans. Amplifiers Modules are available in both Broadband and Band-Specific frequencies. Modular design concepts save time and money, and are lightweight, reliable, cost-effective solutions. We are well-known in the industry for successfully adapting our amplifiers or custom designing new solutions to suit each unique project. Please refer to our Adapted & Custom Design Solutions link to begin formulating your performance objectives and other criteria.
-
Product
Amplifiers
LA-1K
-
Introducting the new LA-1K RF Sensing Dual HF LDMOS 1000 Watt Amplifier. While the LA-1K will work with a wide variety of tuners and transceivers, Palstar custom-designed the LA-1K to work as the perfect match for our very popular HF-AUTO autotuner. MADE IN THE USA
-
Product
Isolation Amplifiers
-
Isolation Amplifiers provide power supply designers with a higher performing, single chip alternative to isolation techniques based on optocouplers and shunt regulators. Analog Devices ADuM3190 and ADuM4190 isolated error amplifiers have a 400 kHz bandwidth, with 0.5% typical initial accuracy at 25°C and 1% total accuracy over the extended temperature range of –40˚C to +125˚C. This provides manufacturers of ac-to-dc and dc-to-dc power supplies with a significant upgrade in speed and operating temperature range, as well as a 5× improvement in transient response.
-
Product
LXI 50Ω Microwave Transfer Switch
60-808-415-010
-
These LXI (Ethernet-controlled) Microwave Transfer Switches are suitable for routing 50 Ω signals up to 50 GHz. With up to 16 switch banks, they are ideal for constructing complex microwave switching systems for many applications. Connection is by front panel mounted SMA. SMA 2.9 or SMA 2.4 connectors.
-
Product
RF Amplifiers up to 6000 MHz
-
Includes RF and microwave amplifiers covering the band from 500Mhz to 6000Mhz in a single module with either GaN or GaAs devices. Custom and standard power amplifiers available with high linearity, low noise figure, and very low error vector magnitude (EVM). Our rack systems and select modules include Automatic Gain Control (AGC), Automatic Level Control (ALC), and peak/pulse/average detection useful in OTA, MIMO, and CTIA testing.
-
Product
Low Noise Amplifier
DLNA8-0.1-18G-2223
-
Low Noise Amplifier, Frequency 1~18GHz, Gain 24dB, Noise figure 3.2dB, P-1dB 22dBm, SMA Female
-
Product
Microwave Comb Generator
-
*Differential output - can also provide two separate single ended complementary outputs. * Pulse height of up to +4V peak into 50 ohms, on positive output * Pulse height of up to -4V peak into 50 ohms, on negative output * Rise time < 80pS, FWHM of approximately 120pS * Produces pulse on both edges of input clock, thereby doubling frequency. * Input clock may be sinewave from 50MHz to 2GHz or square wave from 5MHz to 2GHz, producing fundamental comb tooth energy from 10MHz to 4GHz. * Usable energy to >10GHz. * Can drive any load, including short, without damage. * Power Requirements: -12V @ 120mA and +24V @ 80mA
