Combiners
-
-
Product
Digital Audio Snake System
OmniSnake
-
The OmniSnake consists of a Stage Box that converts microphone/line-level analog inputs to a multiplexed digital signal, and a companion Base Unit that de-multiplexes to provide individual outputs. Digitizing the analog audio at the source eliminates the potential for ground loops, noise interference and crosstalk. Each Stage Box has 8 inputs, and two Stage Boxes can be linked together via coax to form a combined 16 channels, which is carried over coaxial cable to the Base Unit.
-
Product
32Ch Isolated Output Card
SET-1320
-
This card offers 32 optically separated open collector outputs that can switch up to 100mA at 60V. SET-1320 combines tight IO with high isolation voltages and an extensive output voltage range.
-
Product
Protocol and Analyzer Exerciser Software
-
Combine both analyzer and exerciser functionality into one easy-to-use and user-friendly interface for PCIe 5.0® traffic analysis.
-
Product
PH Meter / Tester, 0pH to 14pH, 0.01, 0.2, 400 ms, 0 °C, 50 °C
72-6783
-
The 72-6783 is a 0 to 14pH Meter with 12.5mm LCD display. Any combination of pH electrode and male BNC connector can be used. pH meter included with battery.
-
Product
COM Express Compact Size Type 6 Module with Next Generation Intel Atom® Processor SoC
cExpress-EL
Computer on Module
ADLINK cExpress-EL supports next generation Intel Atom x6000 processors (Elkhart Lake) combined with Intel UHD graphics at low power envelope and high speed interfaces. cExpress-EL modules support In-Band ECC dual channel DDR4 memory up to 32GB, and are also available in rugged operating temperature range and low power envelope, making them a perfect match for mission critical fanless edge computing applications that require safety and reliability at all times.
-
Product
Modular Power
RFP DC High Power
-
AMETEK Programmable Power, Inc.
ReFlex Power™ is a high density, modular programmable power system providing DC, AC and electronic load assets all under control of a single controller. It provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test. The EIA 4U high RFP™ mainframe can hold up to 12 single-slot modules or combinations of single, dual and triple slot wide modules to configure (or reconfigure) the system for the particular requirements at hand. The mainframe can support up to 6 kW of output power.
-
Product
O/E Converter
TIA-4000
-
The TIA-4000 is comprised of a fibre coupled InGaAs APD detector combined with a variable reverse bias voltage network and fast transimpedance amplifier. The output of the unit is brought out to a type K female SMA connector. Light falling on the detector generates a positive-going proportional current. This current, multiplied by the transimpedance produces a voltage that is proportional to the light incident on the detector surface.
-
Product
HDC-AC Equipped
-
The ionizer equipped with a new high-voltage power supply (HDC-AC) was developed independently by Shishido Electrostatic (patented). It is a groundbreaking product that combines high-level static elimination performance with long-term stability. Compared to general ionizers, it has excellent characteristics, such as the ability to maintain static elimination performance for a long period of time without the need for short-term cleaning or part replacement.
-
Product
Time Domain Reflectometer
IRG 2000
-
Cable fault location with the BAUR IRG 2000. The IRG 2000 impulse reflection measurement unit or time domain reflectometer is a handy, easy to carry device for single-phase cable fault pre-location. It is used in combination with a surge voltage generator on low-, medium- and high-voltage cables 0 - 65 km in length. It can also be used on live cables carrying voltage up to 400 V.* Easy and quick cable fault location* Light, compact and manageable* Main unit for the tried-and-tested pre-location method* Ideal for integration in measurement systems
-
Product
Advanced Monitoring Probe
DVB-T/T2
-
Combined with a Network Monitoring System or not, the EdgeProbe Advanced provides a powerful broadcast network alert & diagnosis tool allowing DTV network operators to monitor global trends and anticipate potential failures.EdgeProbe Advanced is able to monitor DVB-T and DVB-T2 signals at transmitter outputs, through its RF inputs (up to 4 in 1RU), as well as at modulator input and at Head-End/distribution links, through its ASI and IP inputs.
-
Product
Large Telemetry Compressive Load Cell
TC-3.0-LG
-
DLM’s Telemetry Compressive Load Cells can be used independently or in combination as part of weighing platforms.They range from 100t to 300t and manufactured using high grade stainless steel, making these load cells particularly suited to rugged environments and the hire industry. Bespoke size compressive load cells can be designed upon request. Some applications include: tank weighing, hydraulic lifting operations, vessel weighing and certification.
-
Product
SmartPower® Intelligent Microwave Generators
-
SmartPower® AX2500 Series intelligent microwave power generators are built on proven experience in designing rugged, reliable microwave power generators for demanding semiconductor fabrication and industrial applications. The compact AX2500 design architecture incorporates field-proven technology, and combines new design features aimed at improved performance and lower cost of ownership.
-
Product
Telemetry Tensile Link
TL-3.0
-
The TL-3.0 is a third generation Telemetry Tensile Link load cell. A light weight wireless tension measuring unit that combines a high level of performance with a robust design for harsh environments.
-
Product
Computer-On-Module
Open Standard Module (OSM)
Computer on Module
OSM form factor is the first computer-on-module form factor for solderable BGA mini modules that is natively capable of supporting both ARM and x86 designs. OSM modules are significantly smaller than previously available modules, with the largest measuring 45mm x 45mm. For a growing number of IoT applications this standard helps to combine the advantages of modular embedded computing with increasing requirements regarding cost, foot print and interfaces. The BGA design makes it possible to implement more interfaces on a small footprint. The largest Size-L (Large) measures 45mm x 45mm with 662 BGA pins. The modules are completely machine processible during soldering, assembly and testing.
-
Product
DH Series High-Temperature Solder-In Tip, 16 GHz BW, 3.5 Vpp Range
DH-HITEMP
-
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
Test Leads
8000 Series
-
The "SOFTIE" by Probe Master lets you say "goodbye" to hand fatigue and finger calluses. A soft probe that bends 90 degrees or more. A probe that conforms to the shape of your hand. This soft flexible probe bends gently to reduce wear and breakage of the lead. Many combinations are possible with the "screw on" accessories shown above. The 48" long, 18GA. test leads, are made of top quality silicone.
-
Product
Multi-function GPS/GLONASS Research Receiver
R100
-
The Multi-function GPS/GLONASS Research Receiver sets the standard in precision and versatility for GPS/GLONASS research. It provides highly accurate navigation, ionospheric measurement, time transfer, satellite monitoring and differential reference station capabilities. When combined with the temperature stabilized antenna it eliminates delay variations due to outside temperature, affording even greater accuracy.
-
Product
Height Gauges
V7
-
This Height Gauge 2D combine technological innovation and tradition. With their touch-display and lateral insert holders, the V7 rank as universal instruments for the workshop.
-
Product
Alarms
IP66 Series
-
Teledyne Gas & Flame Detection
The IP66 Series of Models A-IP66, V-IP66 and AV1-IP66 consist of an audible sounder (A), a visual beacon (V) or a combination of the two (AV1).All of these options come in impact resistant plastic housings that are rated to IP66 for dust and water ingress protection.The visual warning beacon comes in field interchangeable lens colors of amber, blue, clear, green, red, yellow and magenta.
-
Product
FTIR Exhaust Gas Analyzer Direct Measurement Type
FTX-ONE-CS/RS
-
The FTX-ONE offers a 5Hz sampling rate and simultaneously measure the concentrations of multiple components including NH3, CH4, and CO2, from (engine) direct exhaust gas using the Fourier Transform Infrared (FTIR) method in combination with multivariate analysis algorithm.
-
Product
Midi Logger
GL840 Series
-
Modules allow wide range of measurements. Suitable for a variety of measurements due to flexible combinations
-
Product
Arbitrary Generators
-
True variable-clock arbitrary waveform generators with one, two or four channels. DDS arbitrary/function generators and universal generators combining variable clock and DDS architectures.
-
Product
6½ Digit DMM / Digitizer PXI Card
GX2065
-
The GX2065 offers a unique combination of features, resolution, accuracy and speed in a compact, single slot 3U PXI format. Featuring 6-½ digit resolution, 0.005% basic DCV reading accuracy and up to 3,500 reading per second (rps) assures you of measurements that are accurate, fast and repeatable. All measurement functions including digitizing functions are isolated from the PXI bus - providing the ability to make true differential, floating measurements. An on-board controller performs all necessary DMM and digitizer calculations, minimizing PXI control bus overhead.
-
Product
High Temperature Self-Supporting Furnace Extensometers (1200 C)
Model 3448
-
Jinan Testing Equipment IE Corporation
Epsilon developed this unique high temperature extensometer for testing metals, ceramics, and composites at the high temperatures produced by furnaces and induction heating systems. A combination of features make these extensometers easier to use and better in performance than other similar high temperature extensometers.The units are held on the specimen by light, flexible ceramic fiber cords. These make the extensometer self-supporting on the specimen. No furnace mounting brackets are required. The side load on the test sample is greatly reduced because of the self-supporting design and light weight of the sensor. Most materials testing furnaces with a side cut-out for an extensometer will readily accept a Model 3448. For induction heating systems, a different ceramic cord placement allows the extensometer to easily pass between the coils.The combination of radiant heat shields and convection cooling fins allow this model to be used at specimen temperatures up to 1200℃ (2200°F) without any cooling. An optional tiny air fan does enhance stability at the highest temperatures and is recommended for the highest accuracy and for tests with small elongations. The fan comes with a magnetic base for support so it can be mounted at any convenient location near the extensometer. Fan cooling is not generally needed for induction heated systems. High purity alumina ceramic rods are used. These are available in lengths as required to fit your furnace. A spare set is included with every extensometer. Specify chisel, vee chisel or conical contact points as desired.Most units operate equally well in tension and compression. Thus tensile, compression and cyclic tests like low cycle fatigue can all be performed with a single unit.For vacuum furnaces, special models are available. Epsilon can also provide a radiant heat transfer cooled version. This requires that the extensometer module be surrounded by a water cooled enclosure with a front slot for the ceramic rods.
-
Product
3x3 1x1 2x2 1x2 Couplers
-
Couplers can be used to split light from one or more fibers onto two or three fibers or to combine light from two or three fibers onto one or more fibers.
-
Product
R*evolution® Remote Plasma Source
-
The innovative R*evolution® Remote Plasma Source combines field-proven, low-field toroidal plasma technology with an actively cooled plasma chamber made of high purity quartz, significantly reducing oxygen, hydrogen and nitrogen atomic gas loss through wall recombination. Self-contained and compact, R*evolution delivers up to 10 slm of oxygen radicals from a 6kW power supply with true power accuracy of <1% resulting in a high density, extremely clean radical source for photoresist strip and an optimal clean rate greater than 12 microns/min-1. R*evolution can be used for other surface preparation applications.
-
Product
kSA ICE
-
The k-Space Integrated Control for Epitaxy system (ICE) is a modular in situ metrology tool designed for today’s MOCVD and MBE reactors. It combines kSA MOS, kSA BandiT and kSA RateRat Pro patented technologies along with an Emissivity Corrected Pyrometry (ECPR) module. The kSA ICE modular design allows the user to specify which modules will be used in their kSA ICE configuration.
-
Product
Seismic Analysis Software
-
GeoSonics announces our latest software suite. AnalysisNET is the most comprehensive and advanced software for GeoSonics 3000 Series seismograph. The software combines Seismic Analysis and Event Manager software in a single package that employs the .NET framework. AnalysisNET allows easier access to data files provides multiple report combinations and gives you the ability to manage your data.
-
Product
Professional Cable Tester
1EA560
-
Multifuncional tester with LCD display enables to show wire maps and combination of pairs and their lenghts. It also measure the lenght until the broken line / cable. It is suitable for CAT5, CAT5E, and CAT6 cables. With special interface is also suitable for testing of coaxial and telephone cables. It has special unit for testing of cable ends in the other room.
