Loop
See Also: Current Loops, HIL, Loop Testers
-
Product
Power Conversion
-
The XRP6124 is a non synchronous step down (buck) controller for up to 5A point of loads. A wide 3V to 30V input voltage range allows for single supply operations from industry standard 3.3V, 5V, 12V and 24V power rails. With a proprietary Constant On-Time (COT) control scheme, the XRP6124 provides extremely fast line and load transient response while the operating frequency remains nearly constant. It requires no loop compensation hence simplifying circuit implementation and reducing overall component count. The XRP6124 also implements an emulated ESR circuitry allowing usage of ceramic output capacitors and insuring stable operations without the use of extra external components.
-
Product
LXI 8:1 Optical MUX LC Loop-Thru
60-850-421
Multiplexer Module
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
Product
PXI/PXIe 1000Base-T1 Dual Multiplexer With Fault Insertion, Single Channel
40-204-001
Multiplexer Module
The 40-204-001(PXI) and 42-204-001 (PXIe) are single channel differential multiplexers designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They are available with support for 1 or 2-channels of two wire serial interfaces. Each channel pair can be looped out to external equipment or the switches can be used simulate a channel open fault. Using the fault bus, switches can simulate a short between both wires or a short to one of two externally applied fault conditions – such as battery supply or ground - via two fault buses.
-
Product
Fibre Channel Test & Simulation Interface for PCI Express
PCIe-FC4
-
Avionics Interface Technologies
Half-size four lane PCIe board - Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speedsComprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent Analyzer - Supports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
Product
LXI Dual 8:1 Optic MUX SC/PC Loop-Thru
60-850-222
Multiplexer Module
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
Product
Microwave Wideband Synthesizer w/ Integrated VCO
ADF5356
-
The ADF5356 allows implementation of fractional-N or integer-N phase-locked loop (PLL) frequency synthesizers when used with an external loop filter and an external reference frequency. The wideband microwave VCO design permits frequency operation from 6.8 GHz to 13.6 GHz at one radio frequency (RF) output. A series of frequency dividers at another frequency output permits operation from 53.125 MHz to 6800 MHz. The ADF5356 has an integrated VCO with a fundamental output frequency ranging from 3400 MHz to 6800 MHz. In addition, the VCO frequency is connected to divide by 1, 2, 4, 8, 16, 32, or 64 circuits that allow the user to generate RF output frequencies as low as 53.125 MHz. For applications that require isolation, the RF output stage can be muted. The mute function is both pin- and software-controllable.
-
Product
Closed Loop Precise Hall AC/DC Current Sensor
CYHCS-LF
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on closed loop compensating principle and can be used for accurate measurement of DC and AC current, pulse currents etc. The output of the transducer reflects the real wave of the current carrying conductor.
-
Product
LXI 8:1 Optical MUX SC Loop-Thru
60-851-221
Multiplexer Module
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
Product
PXI/PXIe RF Matrix, 16x8, 150 MHz, 50 Ω, SMB, With Y Loop-thru
40-724-011-L
Matrix Switch Module
The 40-724-011-L (PXI) and 42-724-011-L (PXIe) are 16x8 RF matrix modules with y-axis loop-thru and are suitable for switching frequencies up to 150 MHz. Having a 50 Ω characteristic impedance and front panel SMB connectors, these modules provide a simple and scalable bidirectional matrix for RF and are intended for the easy construction of high performance switching systems.
-
Product
sbRIO-9265, Non-Enclosed, 4-Channel C Series Current Output Module
780921-01
Current Input Module
Non-Enclosed, 4-Channel C Series Current Output Module - The sbRIO‑9265 is ideal for interfacing and controlling industrial current-driven actuators at high rates. The module has built-in open-loop detection, which generates an interrupt in software when an open loop is detected as well as zeroing outputs to ensure safety and avoid driving actuators at system power on. The sbRIO‑9265 requires an external power supply and includes a channel‑to‑earth ground double isolation barrier for safety and noise immunity. Non-enclosed modules are designed for OEM applications.
-
Product
PXI/PXIe RF Matrix, 32x8, 150 MHz, 50 Ω, SMB, With Y Loop-thru
42-724-021-L
Matrix Switch Module
The 40-724-021-L (PXI) and 42-724-021-L (PXIe) are 32x8 RF matrix modules with y-axis loop-thru and are suitable for switching frequencies up to 150 MHz. Having a 50 Ω characteristic impedance and front panel SMB connectors, these modules provide a simple and scalable bidirectional matrix for RF and are intended for the easy construction of high performance switching systems.
-
Product
PXIe-2514, 7-Channel, 40 A PXI Signal Insertion Switch Module
780587-14
Signal Module
PXIe, 7-Channel, 40 A PXI Signal Insertion Switch Module—The PXIe‑2514 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXIe‑2514 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls (FADECs).
-
Product
LXI Dual 8:1 Optic MUX LC Loop-Thru
60-850-422
Multiplexer Module
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
Product
Venable Stability Analysis Software
-
In 1983, Venable launched the renowned K-Factor Technique, still in use by many instrument manufacturers today. Venable has elevated the original software with its innovative Stability Analysis program. Go straight from measurement to design using Stability Analysis as its dynamic functionality eliminates lengthy manual value calculations and guesswork. Compensation amplifier synthesis capability, or coefficients for digital power supplies, enables user to achieve exact feedback loop bandwidth and phase margin desired on the first try.
-
Product
Digital Phase Locked Loop (PLL)
A6-CPS
-
The A6-CPS digital phase locked loop (PLL) can be customised to a specific application and shipped ready for use in production.
-
Product
sbRIO-9862, Non-Enclosed, 1-Port, High-Speed, Flexible Data Rate C Series CAN Interface Module
785963-01
CAN Interface
Non-Enclosed, 1-Port, High-Speed, Flexible Data Rate C Series CAN Interface Module—The sbRIO‑9862 is a high-speed Controller Area Network (CAN) Flexible Data‑rate (FD) interface for developing applications with the NI‑XNET driver. The sbRIO‑9862 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The sbRIO‑9862 is only compatible with CompactRIO systems. Non-enclosed modules are designed for OEM applications.
-
Product
Mezzanine System
5041
System
ECM P/N 5041 provides eight channels of RS485 / RS422 I/O with fixed 120 ohm termination for each channel. Speeds are up to 30M bits per second. All channels power up as inputs. Also transceiver inputs are always enabled for loop back diagnostic use when the outputs are enabled. Software can enable outputs on a channel by channel basis.
-
Product
LXI Microwave Matrix, 10GHz, Single 8x4 With Loop-Thru
60-750-184-A
Matrix Switch Module
The 60-750-184-A is a single 8x4 10GHz microwave matrix with loop-thru. It is part of the 60-750/751 range of LXI Microwave Switches controlled through an LXI compliant Ethernet connection. It is available in a variety of configurations and frequencies up to 18GHz (60-751). The matrix is characterized for 50 ohm applications, for 75 ohm versions please consult your local sales representative.
-
Product
PXI/PXIe RF Matrix, 8x4, 300 MHz, 50 Ω MS-M Multiway With Loop-thru
40-729A-002-L
Matrix Switch Module
The 40-729A-002-L (PXI) and 42-729A-002-L (PXIe) are 8x4 50 Ω RF matrices with MS-M Multiway connectors and Y-axis loop-thru. The 4x-727A/728A/729A range are high density RF matrix modules suitable for switching up to 300 MHz in 50 Ω or 100 MHz in 75 Ω. They are available in 50 Ω or 75 Ω versions with SMB connectors or in 50 Ω versions with a multiway connector.
-
Product
Vibrating Sample Magnetometer
VSM
-
The VSM (also named M-H CURVE Hysteresis Graph TEST SYSTEM ) can be used for the measurement of the basic magnetic properties of the magnetic materials. Such as the Hysteresis loops of the materials, Magnetization curve, Warming Curve , Warming /Cooling curve, Cooling curve and the changes of the temperature as time goes away , then we will get some Magnetic parameters such as the Saturated strength of the magnetization, the left strength of the magnetization , Coercive force, the Max of Magnetic energy product,the Curie temperature and the Magnetic conductivity(the Initial Magnetic conductivity is included ). It can also measure the magnetic materials such as the powder, the particles, the films, the liquid and the massive.
-
Product
Combination Measuring Devices According to DIN EN 61557-10 (VDE 0413-10) are permitted
-
PeakTech Prüf- und Messtechnik GmbH
This innovative combination measuring device for testing electrical installations according to official laws convinces with its technical performance data in the high-end area. All important safety tests such as FI, voltage, loop, low-resistance, earth resistance and insulation tests for e-checks and new installations can be carried out safely by the electrician via the large 3.5“ TFT color display. Of course, the device comes with an extensive range of accessories, such as all necessary test leads, adapters, rods and the required software CD for the PC. The device can be charged with a power adapter or via a car adapter. During the daily use, this high-quality device is protected against dust and all-round water jets by its protection class IP 65.
-
Product
Active Loop Antenna
KH30935
-
Beijing KeHuan Century EMC Technology Co,.LTD
KH30935 active loop antenna is used for adjusting, testing, measuring and other receivers. It has many advantages:1. The antenna coverage frequency is wide: 150KHz ~ 30MHz .2. The field strength value is measured according to the correction coefficient within the effective frequency range, which is convenient to use.3. The antenna has a small outer diameter and light weight, which is convenient for outdoor measurement.
-
Product
1.25GS/s 16Bit 1GS Mem 12CH Arbitrary Waveform Generator
P12812B
Waveform Generator
The Proteus P12812B, is a 1.25GS/s, twelve channel arbitrary waveform generator packaged in a 4U, 19” standalone box with a 9” touch screen and on board PC , offering technologically advanced options and configurations that integrate the ability to transmit, receive and perform digital signal processing all in a single instrument. The P12812B offers industry leading performance Including an innovative task oriented programming, real time data streaming, fast feedback loop for environment dependent waveform generation and user customizable FPGA for application specific solutions.
-
Product
PXIe-2512, 7-Channel, 10 A PXI Signal Insertion Switch Module
780587-12
Signal Module
PXIe, 7-Channel, 10 A PXI Signal Insertion Switch Module—The PXIe‑2512 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXIe‑2512 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls (FADECs).
-
Product
NI-9861, 1-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module
781962-01
CAN Interface
1-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module—The NI‑9861 is a fault-tolerant Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. The NI‑9861 is ideal for applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other data acquisition measurements in the same NI CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same NI CompactRIO chassis.
-
Product
Public Switch Telephone Network Tester
295B
-
The Testphone 295B is a test telephone designed for use on Public Switched Telephone Networks (PSTN). It is designed for use on both Dual-tone Multi-frequency (DTMF - tone dialling) and Loop Disconnect (LD - pulse dialling) lines. Fitted with an integral ADSL filter, the telephone will not cause interference when connected to ADSL/Broadband lines in either `on hook` or `off hook` mode.
-
Product
LXI Microwave Matrix, 10GHz, Dual 4x4, Terminated With Loop-Thru
60-750-244-C
Matrix Switch Module
The 60-750-244-C is a dual 4x4 10GHz microwave matrix with internal termination and loop-thru. It is part of the 60-750/751 range of LXI Microwave Switches controlled through an LXI compliant Ethernet connection. It is available in a variety of configurations and frequencies up to 18GHz (60-751). The matrix is characterized for 50 ohm applications, for 75 ohm versions please consult your local sales representative.
-
Product
LXI Microwave Matrix, 10GHz, Single 4x4, Terminated With Loop-Thru
60-750-144-C
Matrix Switch Module
The 60-750-144-C is a single 4x4 10GHz microwave matrix with internal termination and loop-thru. It is part of the 60-750/751 range of LXI Microwave Switches controlled through an LXI compliant Ethernet connection.
-
Product
2.5GS/s 16Bit 1GS Mem 4CH 8 Markers AWG
2584M
-
The Proteus P2584M, is a PXIe based, 2.5GS/s, four channel arbitrary waveform generator offering technologically advanced options and configurations such as, a dual channel 2.7GS/s digitizer with 9GHz bandwidth, to transform the instrument to an arbitrary waveform transceiver. The P2584M offers industry leading performance Including an innovative task oriented programming, real time data streaming, fast feedback loop for environment dependent waveform generation and user customizable FPGA for application specific solutions.
-
Product
PXI/PXIe Wide Current Range Matrix Module, 6x4, 2-Pole, X & Y Loop-thru
40-514-002
Matrix Switch Module
The 40-514-002 (PXI) and 42-514-002 (PXIe) are low density matrices in 6x4 2-pole configuration. They are capable of switching a wide range of current, from 10 μA to 2.5 A at 220 VDC/250 VAC. The current capability of the module permits the use of a single module type for both low and medium current test applications.
