CompactPCI Chassis
A metal frame that serves as the structural support for a CompactPCI bus. (sbc.webopedia.com)
-
Product
6-slot Chassis
CH-06 AXIe-0
-
The 6-slot chassis in AXIe-0 format is intended for use in modular measurement information systems based on the AXIe standard.
-
Product
Rack Mount Kestrel Chassis A-Series
0072
-
ATXstyle Motherboard, 3 x 5-1/4" Bays, 2 x 3-1/2". A 10-Slot HP 1000 backplane, cooling fans, and slides are provided plus space for a standard ATX PC motherboard, diskette and hard drives (3 x 5-1/4" and 2 x 3-1/2").
-
Product
Electronical Load Board 3U CompactPCI (conduction cooled)
046-712
-
The 3U load boards are designed to simulate the power consumption of a single board computer and other boards on the backplane.
-
Product
550 HP Water Brake Chassis Dynamometer
CM-51S
-
AC power, air and water required at one side wallas applicable.• Room length, and pit location within length,must be determined by user to fit maximumtruck length and rear overhang.• Provide at least one man door for fire escapenear rear of room, but not in rear wall becausesomeone entering during a test could be struckby a stone flung from a tire. Provide ample fireextinguishers at each door and near driver.• “Back-on, Drive-off” installation configurationpreferred.
-
Product
3U CompactPCI Serial M.2/U.2/SATA Storage Carrier
cPCI-A3H20
Carrier Board
- 1x NVMe M.2 and 1x NVMe U.2 drive slot- 1x optional SATA 6Gb/s M.2 drive slot shared space with NVMe U.2- Status LEDs on faceplate: drive activity, hot-swap status, user-configurable- Operating temperature: -40°C to +85°C with qualified modules- EN50155 compliant
-
Product
3U CompactPCI Serial 8-slot SSL w/ RTM w/ Ethernet
1CPCIS-308-L210
-
3U CompactPCI Serial Backplane with 8 CompactPCI S.0 slots, system slot left, with rear IO : 1x CompactPCI S.0 CPU slot, 7x CompactPCI S.0 peripheral slots, with connectors for RTMs (Rear Transition Modules) in slots 2 to 8, Ethernet full mesh.
-
Product
6U CompactPCI Dual 64-bit PMC Slots Carrier Board
cPCI-8602
Carrier Board
- Supports two single-size 32,64-bit/33,66 MHz PMC sites in 4HP width- PICMG® 2.0 32,64-bit/33,66 MHz cPCI bus- PICMG® 2.1 Hot Swap Specification Compliant- 3.3V or 5V V(I/O) for cPCI bus and PMC sites- PLX® PCI-to PCI bridge PCI6154 for PCI bus- Power and HotSwap LED incidators on front panel
-
Product
CH-06 PXIe 6-Slot Chassis
(Gen3, 500W)
-
The new CH-6 PXIe chassis allows you to create high-performance multifunctional systems for both collecting and processing large data flows, and systems for monitoring and adjusting electronic equipment.
-
Product
3U CompactPCI Quad-Core Intel Atom® Processor Blade
cPCI-3620
Processor Blade
The ADLINK cPCI-3620 Series is a 3U CompactPCI® processor blade featuring a quad-core 4th generation Intel® Atom SOC and soldered DDR3L-1333 ECC memory up to 4GB.
-
Product
3U CompactPCI Serial 4-slot SSR w/ RTM w/ Ethernet
1CPCIS-304-R210
-
3U CompactPCI Serial Backplane with 4 CompactPCI S.0 slots, system slot right, with rear IO : 1x CompactPCI S.0 CPU slot, 3x CompactPCI S.0 peripheral slots, with connectors for Rear Transition Modules (RTMs) in slots 1 to 3, Ethernet full mesh.
-
Product
LXI Chassis X Plugin - 8x8 Matrix
65-110-201
Matrix Switch Module
The 65-110-201 is an 8x8 matrix plugin for the 65-110A chassis. At least one is required to be fitted to these chassis assemblies that are configured for Y=8 applications. The number of plugins is determined by dividing the X axis size required by 8 and rounding the number up to the next integer.
-
Product
CompactPCI 6U 6 Slot left justified, 32 bit, P1s, P2-5l
105CP3L606-1057
-
CompactPCI 6U 6 slot 32 bit with system slot left, fully compliant to the PICMG basic specification 2.0 R3.0 and Hot Swap specification 2.1 R1. User defined VI/O is standard.
-
Product
8-Slot ShoeBox Chassis
AX60552
-
*Two 5.25 and one 3.5 HDD drive bays*Desktop or wallmount industrial computer chassis*Equipped with PS/2 type power supply
-
Product
15-Slot 32-Bit 3U I/O with 6U System CompactPCI Backplane
cBP-6515R
Backplane
- PICMG:2.0 R3.0, 2.1 R2.0, 2.7 R1.0- Dimension:202.5 x 262.05 (mm, WxH, vertical insertion view)- Segment:One- cPCI Bus:32-bit/33MHz- System Slot:Right-hand side- System Slot Rear I/O:P3, P4 and P5 rear I/O with AB-type shroud- Peripheral Slot:14 (Bus A: 7 slots, Bus B: 7 *slots)Note- Peripheral Slot Rear I/O:P2 rear I/O with AB-type shroud
-
Product
3U CompactPCI Serial 7-slot SSR w/o RTM w/ Ethernet
1CPCIS-307-R100
-
3U CompactPCI Serial Backplane with 7 CompactPCI S.0 slots, system slot right, without rear IO: 1x CompactPCI S.0 CPU, 6x CompactPCI S.0 peripheral slots, without connectors for RTMs, Ethernet single star from system slot to all peripheral slots.
-
Product
4-slot LXI Chassis
MezaBOX-4M LXI
-
MezaBOX-4M LXI is a device that ensures the operation of various mezzanine modules (up to 4) installed in it, under the control of a personal computer via USB2.0 or ETHERNET 10/100/1000 Base T (local area network) interfaces of a personal computer ... MezaBOX-4M LXI is intended for use as a mezzanine carrier in multichannel systems for collecting / issuing information, both digital and analog.
-
Product
3U CompactPCI® 4 RJ45 Port Gigabit Ethernet Card
MIC-3958
-
Advantech MIC-3958 Series, a 3U height 4HP CompactPCI® peripheral card, using Intel® i210 Ethernet controller, to support up to four RJ45 Gigabit lan connectors, two switchable with rear transition module; MIC-3958A provides four RJ45 lan ports on front panel, MIC-3958R provides two RJ45 lan ports on rear IO panel. Its ideal power solution make it perfect for all fanless system applications.
-
Product
CompactPCI 6U 64 bit ATX 6 slot, P1s, P2-5l, RoHS
102CPCI606-4057R
-
CompactPCI 6U 6 slot 64 bit low Easycable, system slot left, with ATX connector. It is fully compliant to the PICMG basic specification 2.0 R3.0 and Hot Swap specification 2.1 R1.0.
-
Product
3U CompactPCI® Subsystem with 8-slot Backplane and 1 + 1 CompactPCI® Redundant Power Modules
cPCIS-2632 Series
Backplane
- 3U CompactPCI® backplane with seven peripheral slots and one system slot- Temperature, voltage, and fan monitoring LEDs- Supports current sharing on +5 V, +3.3 V, and +12 V- 1 + 1 hot swappable 250 W + 250 W CompactPCI® power supplies- PICMG® 2.11 47-pin power interface- Hot-swappable cooling fans & filter
-
Product
CompactPCI 6U 64 bit ATX 8 slot, P1-2s, P3-5l, RoHS
102CPCI608-4157R
-
CompactPCI 6U 8 slot 64 bit low Easycable, system slot left, with ATX connector. It is fully compliant to the PICMG basic specification 2.0 R3.0 and Hot Swap specification 2.1 R1.0.
-
Product
compactPCI Bus Pin Assignment
-
VECTOR Electronics and Technology, Inc.
cPCI Bus pin assignments per PICMG 2.0 R3.0
-
Product
4U cPCI Chassis
DP-cPCI-8118
-
DP-cPCI-8118 is a compact high performance 4U cPCI chassis. Complaint with the compactPCI specifications this provides the right platform options to meet small system integration needs. The chassis features modular construction and integrated cooling. The DP-cPCI-8118 is available with high-performance backplane and ATX power supply.
-
Product
3U CompactPCI® RS-232/422/485 Serial Communication Card
MIC-3955
-
The MIC-3955 is a low power 4-port or 8-port RS232/RS422/RS485 serial board with 3U CPCI form factor and is based on the EXAR PCI controller. MIC-3955 is PICMG 2.0 Rev. 3.0 compatible. Rear board module are named MIC-3527XX. The MIC-3955 supports front IO or rear IO with 4-port and 8-port, and every channel is independent.
-
Product
3U CompactPCI 2-slot SSL 33MHz VIO 5V BW 64-Bit
80932-002-6600
-
3U CompactPCI backplane 2-slot, PICMG 2.0 R3.0, system slot left, supports full hot swap function according to PICMG 2.1 R2.0 hot-swap specification, clock frequency 33MHz, V(I/O) +5V, bus width 64-bit, power input connection with Fastons connectors
-
Product
9-slot Chassis
CH-09 AXIe-0
-
The 9-slot chassis in AXIe-0 format is intended for use in modular measurement information systems based on the AXIe standard.
-
Product
2-slot VXI Chassis
-
The 2-slot VXI compact crate is designed for use in modular VXI instrumentation systems.
-
Product
CompactPCI CTEL 7U 2 Slot with H.110 bus, P1-2s
105CTEL702-0136
-
CompactPCI CTEL 7U 2 slot with system slot left, H110 bus, fully compliant to the PICMG basic specification 2.0 R3.0, Hot Swap specification 2.1 R1, andv PICMG H.110 Computer Telephony specification 2.5 R1.0.
-
Product
Chassis Mounting Kit For 40-922 & 60-102
63-102-001
Mounting Kit
This chassis mounting kit is designed for use with the our 8-slot PXI chassis (40-922) and our 7-slot LXI modular switching chassis (60-102), allowing installation into a standard 19" rack. The frame increases the overall height to 5U and allows space for cooling air to be drawn into the underside and expelled from the top of the chassis
-
Product
NITlab Chassis Manager Card
-
NITLAB designed and implemented a Chassis Manager(CM) card to control and monitor NITOS nodes. CM card is comprised of a general-purpose microcontroller, an ethernet microcontroller and a relays circuit. General-purpose microcontroller supports a tiny web server and can serve http requests such as power on/off and reset. Furthermore, it returns the operation status of the node and can support a temperature & humidity sensor and a light sensor as well.
-
Product
6U CompactPCI Rear Transition Module with Intel® Ethernet Controller I350-AM2
cPCI-R6100 Series
Controller
- Intel® Ethernet Controller I350-AM2- Up to four Ethernet GbE ports- Dual display, DVI and VGA- CompactFlash and SD card slots for onboard storage
