CompactPCI Chassis
A metal frame that serves as the structural support for a CompactPCI bus. (sbc.webopedia.com)
-
Product
14-slot Chassis
CH-14 AXIe-0
-
The 14-slot AXIe-0 chassis is intended for use in modular measurement information systems based on the AXIe standard.
-
Product
Diesel Fleet Maintenance Chassis Dynamometer
MD-7500
-
At the heart of the MD-7500 is a set of three air-cooled eddy current power absorbers. Each absorber, or brake, can hold up to 600-hp (total power of 1,800-hp) more than enough to simulate a fully loaded transit bus. As the systems PAU''s (brakes) are air-cooled, no water is required to or from the device eliminating the high cost of water consumption and/or the cost of an expensive water recovery system which can sometimes exceed the cost of the dynamometer system itself. Mustang is the only company that offers a Universal Fleet Test Bed without water supply requirements.
-
Product
VPX Chassis 10U/84HP 10 Slots
BKP6-CEN10-11.2.4-4
-
This 10 slot Hartmann Open VPX BKP6-CEN10-11.2.4-4 profile system chassis provides a high performance packaging solution for 6U VPX modules as SBC’s, GPU’s FPGA boards. The 84HP wide, rack-mountable enclosure for vertical mounting of boards is outfitted with two 1000W plug-in VPX power supplies and a 3U bottom mount fan tray.
-
Product
Compact Industrial Computer Chassis For PCE-2000
IPC-242
-
Compact Industrial Computer Chassis for PCE-2000 Series CPU Board and 250W PSU. Compact IPC chassis with two front expansion slots, Compact design for small cabinet or limited space. 2 - 3 independent displays (HDMI/VGA/DP or DVI) 4 expansion slots (PCIe/PCI).
-
Product
ARINC 3U/6U CompactPCI Interface Card
CPCIC3/6-A429
Interface Card
Alta Data Technologies’ CPCIC-A429 interface module offer a variety of ARINC-419/429/575/573/717 channel configurations with software selectable RX/Tx channels, baud rates, bit encoding and word configurations (Start/Sync/Stop length, Parity, bits/word, MSB/LSB).Encode or decode almost any ARINC-429 physical layer signal.
-
Product
6U CompactPCI Rear Transition Modules
Rear Transition Module
ADLINK offers a diverse line of Rear Transition Module (RTM) to 6U CompactPCI platform to deliver more I/O connectivity.
-
Product
14-Slot Chassis
ATCA CO14G4 AC 14 Slot 15U
-
The new flagship AdvancedTCA® 14-slot chassis, AC version is Comtel’s “4th Generation” and the latest in high performance platforms for ATCA. Its modular design offers ultimate flexibility to provide a solution tailored for your needs.
-
Product
3U CompactPCI Serial MXM GPU Carrier Card
cPCI-A3MXM
Carrier Board
- Follow PICMG® CompactPCI® Serial design guide- CompactPCI® Serial, 3U 4HP/8HP (100mm x 160mm)- Compatible with MXM Type A (82 mm x 70 mm) or Type B (82 mm x 105 mm)- Support NVIDIA A1000 with 2048 CUDA® cores, 16 RT Cores and 64 Tensor Cores or NVIDIA RTX™ A4500 with 5888 CUDA® cores, 46 RT Cores and 184 Tensor Cores- 4x DisplayPort 1.4, support 4K (3840x2160) resolution- Operating temperature: -40°C to +70°C- Designed to meet EN50155 standards
-
Product
CompactPCI Instruments
-
Is a computer bus interconnect for industrial computers,combining a Eurocard-type connector and PCI signaling and protocols. Boards are standardized to 3U or 6U sizes, and are typically interconnected via a passive backplane. The connector pin assignments are standardized by the PICMG US and PICMG Europe organizations. The connectors and the electrical rules allow for eight boards in a PCI segment. Multiple bus segments are allowed with bridges.
-
Product
3U CompactPCI Serial Front Removable SATA Carrier for SSDs
SD8-STEEL
-
The SD8-STEEL is a peripheral slot card for CompactPCI® Serial systems. It includes a shuttle for 1.8 or 2.5” SSD or HDD drives. Signal integrity is optimized with 6Gbps SATA drivers. A push button ejection of the drive enables easy swap removal.
-
Product
18-Slot 3U PXI Express Chassis with AC - Up to 8 GB/s
PXES-2780
Chassis
The ADLINK PXES-2780 is an 18-slot PXI Express chassis, compliant with PXI Express and cPCI Express specifications and offering one system slot, one system timing slot, ten hybrid peripheral slots, and six PXI Express peripheral slots for a wide variety of testing and measurement applications requiring enhanced bandwidth. The PXES-2780 provides a configurable PCIe switch fabric and is configurable in two-link, and four-link PXI express deployments, with 8 GB/s system bandwidth and up to 4 GB/s slot bandwidth for dedicated peripheral slots, thanks to PCIe gen2 signaling technology.
-
Product
4U Chassis
-
4U chassis comes in 4U 24 Bay provides enhanced storage capacity and redundant power supplies. With Multi-core processor and 8 hot-swap hard drive cages, 4U chassis offers 4U tower/rackmount server chassis designed for EATX serverboards.
-
Product
Chassis
-
Infrastructure housing for instrument cards typically containing a power supply, cooling fans and emi shielding.
-
Product
12-/16-bit 16 Channel DAC for CompactPCI
CPCI395
-
The CPCI395 features 16 analog voltage outputs, integrated on the CompactPCI standard. Each output has a 12- or 16-bit resolution and a software programmable output range (0..+10V or -10..+10V). Control of the analog output is as easy as writing the binary equivalent to a dedicated register (per channel). Conversion takes place automatically. If desired, channels can be synchronized by presetting the channels and then give a simultaneous update command.
-
Product
For Conduction Cooled ΜTCA Chassis
UTC003
-
The VadaTech UTC003 is the most feature-rich MCH (MicroTCA Carrier Hub) for the Conduction Cooled μTCA chassis in the market. It’s management software is based on VadaTech’s proven Carrier Manager and Shelf Manager. The MCMC manages the power modules, the two CU (Cooling Units) and up to 12 AMCs within the μTCA chassis. It also interfaces to and manages the on-board fabric interfaces. The module is available with PCIe, SRIO, 10GbE Layer 3 managed, and GbE Layer 2 managed. The UTC003 runs Linux 2.6 on it’s MCMC CPU and is hot-swappable and fully redundant when used in conjunction with a second instance of the module. The firmware is HPM.1 compliant which allows for ease of upgrade. The UTC003 provides Fabric (100 Mhz HCSL) clock to each AMC.
-
Product
14-slot CH-14 PXIe-PC Chassis
-
The new CH-14 PC PXIe-PC chassis with an embedded PC allows the creation of high-performance multifunctional systems for collecting and processing large flows of information, as well as systems for monitoring and adjusting radio-electronic equipment.
-
Product
LXI Chassis
-
Our LXI chassis allow any of our 3U PXI switch modules and many of our instrumentation modules to be controlled in an Ethernet environment. You may also be interested in our 2-Slot USB/LXI Chassis, this chassis allows most of our 1 or 2-slot PXI modules to be controlled via USB or Ethernet. Also our 4-Slot USB/LXI Chassis allow USB or Ethernet control of most PXI modules up to 4-slot width. For more information on these chassis, you can look in the bottom part of the table below.
-
Product
8 Slot, 3U, 350W, PXI Chassis
40-908-001
Chassis
This PXI chassis includes all the features and performance required by version 2.1 of the PXI standard and supports a control interface or embedded controller and up to seven more 3U peripheral modules.
-
Product
CompactPCI & CompactPCI-X Bus Analyzer / Exerciser
CPCI850
-
The CPCI850 analyzer provides a multitude of functions to help analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation- Target memory with addressable windows- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics- Compliance testing
-
Product
Stepper Motor Controller for CompactPCI
CPCI322
-
The CPCI322 is a 3U CompactPCI card. The CPCI322 Intelligent Stepper Motor Controller is designed to drive external amplifiers. This is an ideal solution for all applications where stepper motors must be controlled with a maximum of flexibility and a minimum of overhead.
-
Product
2U 6-Slot Rackmount Chassis
ACP-2000
-
2U 6-Slot Rackmount Chassis with Front USB and PS/2 Interfaces
-
Product
Chassis Controllers and Bus Expanders
-
With over 20 different chassis configurations, our Smart PXI chassis product line (3U chassis, 6U chassis, 3U/6U chassis) offers the most features, slot configurations, UUT interface options, system power, and embedded / external controller options in the industry.
-
Product
400 W 6U CompactPCI Hot-Swappable Redundant Power Supply
cPS-H640/48
Redundant Power Supply
- PICMG® 2.11 CompactPCI® Power Interface compliant- 6U CompactPCI® 8HP form factor- PICMG® 2.11 47-pin CompactPCI® in-rack power module interface- 400 W DC output, maximum 480 W peak output
-
-
Product
cPCI-6636(KL) Series 6U CompactPCI Processor Blade
20040260
-
The cPCI-6636 Series is a 6U CompactPCI® processor blade based on the 6th/7th Generation Intel® Xeon® E3 and Intel® Core™ i3/i7 Processors with Intel® HM170 or CM236 Chipsets. The cPCI-6636 supports up to 16GB onboard DDR4-2133 memory and 16GB DDR4-2133 via SODIMM. Total memory capacity is up to 32GB of DDR4-2133. The cPCI-6636 is a highly integrated processor blade fit for mission critical applications in industries ranging from automation to defence.
-
Product
VPX 3U 1 Slot Chassis
HAWK
-
Combined with our IGUANA OpenVPX 3U switch module or Juniper Networks LN-1000 rugged router the HAWK is a very small but fully ruggedized networking platform. Combined with our 3U VPX Intel I7 CPU module it can be configured to meet various demands
-
Product
3U CompactPCI Multi-Function I/O Board
CPCI-AD32
Multifunction I/O
The CPCI-AD32 is a 3U CompactPCI multi-function I/O board. The CPCI-AD32 offers 32 channels of 16 bit A/D, two 16 bit D/A, 16 digital I/O, counter / timers.There is a local 60 Mhz TMS320C31 DSP processor to supervise all the I/O activity. The DSP can be programmed by the end user to execute application specific code. The CPCI-AD32 is ideally suited for factory automation, automatic test equipment, test & measurement, and control systems.
-
Product
CompactPCI Serial 3U Backplanes / Power connector
-
Hartmann Electronic’s cPCI Serial Backplanes are compliant to the PICMG CPCI S.0 CompactPCI Serial specification. This backplane features 1 power slot in addition to either 6 or 9 cPCI serial slots.
-
Product
Wallmount Industrial Chassis Supports 10-Slot Backplane
RK-609B
Chassis
- Supports 10 slot PICMG backplane- Two 5.25" and two 3.5" external drive bays, one internal 3.5" drive bay- Upper cover with captive screw- Drive bay with shock and vibration resistant design- Replaceable and easy-to-clean air filter- 12cm cooling fan (85CFM)- Two USB and one PS/2 keyboard connectors on front panel
-
Product
Rack Mount Osprey Chassis 4-Slot Unibus
0249-U
-
10.5" high by 19" wide by 20" deep (267 x 483 x 508 mm), this chassis is FCC certifiable**. AT style motherboard, 3 x 5-1/4" bays, 2 x 3-1/2" bays. Cooling fans and space are included for user's hex-height, 4-slot DD-11 Unibus backplane, PC motherboard, diskette and hard drives (one hidden and four visible half-height bays).
