Positioning
Aligning test set with target geography.
-
product
Renishaw Styli
Advanced Industrial Measurement Systems
Renishaw’s styli are some of the most accurate in the market. The balls on the end of the styli are bonded to the stems to ensure that there is no wiggle room – as compared to the traditional ball drilling method to fix the stem to the ball – which causes distortions, and thus measurement errors. Renishaw’s styli are a much more capable option for the CMM. These balls also perfectly spherical, are located at the optimum position on the stem, are threaded nicely and are extremely sturdy during measurement. Additionally, Revolution® CMM’s are supplied with Renishaw Grade 5 High Accuracy Styli.
-
product
Reservoir Isolators
Fluid contamination can lead to high maintenance costs and downtime in hydraulic systems. Parker reservoir isolators provide protection against the ingestion of airborne contaminants such as dust, chemicals and water vapor through the breather-vent of your hydraulic system. Utilizing an elastomer bladder as a lung, the changes in gas volume in a hydraulic system's reservoir can be trapped and prevented from mixing with the outside atmosphere. Unlike conventional breather-vent filters, Parker reservoir isolators provide a positive separation without the possibility of clogging or need for maintenance.
-
product
HIPOT Insulation Testers
Crown high voltage, transformer type hipot insulation testers are safe, easy to use for quick, positive determination of grounds, shorts, and broken wires in motors, transformers and other low voltage equipment or wiring systems. A turn of the selector switch gives a selection of seven voltages; 500, 1080, 1250, 1500, 1750, 2000 or 2500 volts calibrated to +/- 5% accuracy; NEMA recommendation for insulation test is twice normal voltage plus 1000 volts. Since this instrument has a capacity of 2500 volts, it readily accommodates all normal requirements.
-
product
Hydraulic Dampers
The ACE hydraulic dampers are similar in appearance to our industrial gas springs but are adjusted in the end position and work differently to the DVC family with individual speed adjusters for the push and pull direction. This provides users with the maximum flexibility.
-
product
Cut Susceptibility Tester
King Design Industrial Co., Ltd.
Equipment conforms to IEC61730 MST12 specification. Pre- or post-round can be selected for control wiring connection. With weights block’s positioning pin is removed before test; and is inserted in the rear positioning hole for the remaining time. Equipped with rings at both front and rear end; used to connect a rope and control the driving direction. Use replaceable special cutting chip.
-
product
SparkFun GNSS-RTK Dead Reckoning Breakout
ZED-F9K (Qwiic)
The SparkFun ZED-F9K GNSS Breakout is a high precision, sensor fusion geospatial board with equally impressive configuration options and takes advantage of u-blox's Automotive Dead Reckoning (ADR) technology. The ZED-F9K module provides a highly accurate and continuous position by fusing a 3D IMU sensor, wheel ticks, a vehicle dynamics model, correction data, and GNSS measurements.
-
product
Broadband Coaxial Noise Sources
Our integrated noise modules contain all the required biasing circuitry and only need a positive voltage to activate for an easy installation. Since they typically do not contain amplification, the raw noise output from the diode is seen at the output of the module resulting in a maximum ENR of approximately 35dB. Primary applications include system built-in test and laboratory use.
-
product
Arbitrary Power Supply
Toellner Electronic Instrumente GmbH
Can generate relatively rapid variations of both voltage and current. It is designated an arbitrary DC power supply, if these variations take place within one quadrant (that is, both voltage and current remain positive at all times).
-
product
2D Scanning Unit
intelliSCAN FT
The intelliSCAN FT is a 2D scanning unit for planar remote laser applications. Fix integrated in the welding machine or attached to a Gantry system, the scan unit ensures fast and precise positioning of the laser spot.
-
product
Solid State Flasher, DC Input
A738
NAI’s A738 is a 2.5 A, DC Input, Aircraft Warning or Position Light Flasher. This solid-state, single-channel unit is designed for airborne use and performs to all applicable military specifications.
-
product
sbRIO-9222, Non-Enclosed, ±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
785479-01
Non-Enclosed, ±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The sbRIO‑9222 performs differential analog input. This module is well suited for applications such as ballistics, impact, and blast wave testing. The sbRIO‑9222 can sample at the maximum sample rate per channel while the module next to it samples at a much slower rate, which is ideal for mixed-measurement test systems. There are two connector options for the sbRIO‑9222: a 10‑position screw terminal or a 25‑pin D‑SUB connector.
-
product
Universal Multichannel System up to 100V
- From 12 to 48 independently controllable High Voltage channels- 0 ÷ 100 V output voltage- Maximum Current: 1mA, 10 mA or 1 mA/100 μA (dual range board)- Individual Enable (A1510 only)- Either DB37, DB25 or SHV connectors- Available with either positive, negative or mixed polarity- Up to 20 nA / 100 pA current set / monitor resolution- Up to 2 / 0.2 mV voltage set / monitor resolution- Extreme Low ripple, down to < 3 mVpp- 3 different channel grounding- Common Ground (AGxxxx)- Common Floating Return (Axxxx)- Full Floating (A1510 only)- Independently programmable for each channel:- Output voltage- Current limit- Ramp up/down- TRIP parameter- Current generator operation in overcurrent condition- Specific design for double side silicon detector (A1510)
-
product
Portable Analyzers
The key to the operation of Alpha Moisture Systems' Portable Analysers is the unique Desiccant Dry-Down Chamber. By keeping the sensor dry between tests, the special assembly of the head ensures that the instrument is always ready for immediate use. The head assembly consists of two chambers which have a telescopic action. When the head assembly is in the 'closed' or 'Dry-Down' position, the sensor is completely surrounded by desiccant, which absorbs the remaining water moisture from the sensor and hence it is dry and ready for use. The small space at the bottom of the test chamber enables the sample pipe to be purged before the test commences without wetting the sensor. By placing a finger over the outlet of the head, the sample pressure is able to open the test chamber automatically, exposing the sensor to the gas being tested and enabling accurate reading of moisture content in the sample gas. After each test the head assembly is closed by depressing the inner section so that the sensor will again be dried by the desiccant, leaving the sensor ready for use time and time again. The desiccant is kept in the inner chamber and is not exposed to ambient room air or the sample gas, therefore there is no need for frequent regeneration or replacement of the desiccant.
-
product
Digital Brushless Servo Drives
DA Series
The DA series high performance digital servo drives integrates digital position and velocity control with built-in power supplies and the latest in PWM servo amplifier technology. Power range up to 50KVA.
-
product
Photohelic Pressure Switch Gage
A3000
Photohelic Switch/Gages function as versatile, highly repeatable pressure switches combined with a precise pressure gage employing the time-proven Magnehelic gage design. The Photohelic switch/gage measures and controls positive, negative or differential pressures of air and compatible gases
-
product
Engine Speed Control and Measurement (Test Set A)
MS 1100
*Checks the parameters such as current, voltage, speed, and turbine gas temperature of 804E and 811 engines Portable instrument*Testing of Automatic engine control system and after burner control system*Simulates the temperature signal derived from the engine TGT (Temperature Gas Turbine) thermocouples*Simulates the speed signal, NL (low pressure shaft speed signal) drive from the L.P shaft Probe*Indicates the current signal to the FCU solenoid derived from the engine control amplifier*Measure the TGT and NL simulated signal at static position*Measure the signal produced by the engine TGT thermocouples*Measure the NL signal produced by the LP shaft*Measure the NH (High-pressure shaft speed) signal produced by HP shaft*Indicates the solenoid current, produced by the engine control amplifier*Indicates the solenoid voltage, produced by the engine control amplifier*Used to test engine in both static and dynamic states
-
product
Networkcontroller
A new set of motorized tables developed by Klocke Nanotechnik allows high strokes at small volumes. The modules are driven by the Nanomotor®. Loads of up to two kg can be moved over centimeters of stroke with down to 2 nm resolution. Manipulation in many degrees of freedom is possible without backlash. The modules NMT xx-L are longer, but thin like a pencil. In most of the NMT-modules position measurement systems can be included without increasing the size. The resolution of the position sensor is better than 10 nm. All NMT modules can easily be fixed onto each other. Very small connectors allow the exchange of a module without removing cables. The NMT-Zxx are modules for vertical movement. They have an internal load compensation to lift up loads. Nanomotor-Grippers and force sensors that can easily be fixed on these modules are available.
-
product
Motors
When your application demands ultra-precise positioning and high throughput, trust Aerotech’s motor expertise.
-
product
20"D Retractable Writing Shelf for 19" Racks
WS-021920
19" x 20"D retractable writing shelf operates smoothly on ball bearing slides which lock in fully extended position.
-
product
3D Scan Systems
intelliWELD
The intelliWELD is a 3D scanning unit for remote laser welding applications. While a robot leads the scan system along the processing line, the scan unit ensures the fast and precise positioning of the laser spot.The intelliWELD scan unit allows elimination of complex robot movements and fast repositioning, reducing the repositioning time between the welds to a few milliseconds.
-
product
Portable Microscope With XY Stage, X400 1mm Field Of View, 1µm High Resolution
*Counting of cells, algae and other samples*Easy positioning of the sample*Methodically scanning of slides and some counting chambers*Works with standard microscope slides (25x75mm or 1”x2”) and 32mm wide counting chambers (top cover of counting chamber needs to be <1mm thick)*Allows manual movement of the slide and counting chamber independently in the left-right (X) axis and front-back (Y) axis
-
product
Hydrophones & Transducers
Teledyne Marine manufactures a broad range of hydrophones. From oceanographic research to monitoring industrial processes, we have a range of hydrophones for reference measurement, reference projectors, passive arrays, positioning systems and tracking systems. And if you cannot find the right hydrophone, we'll work with you to develop a solution that meets your specific needs.
-
product
Signal 90 Series Modules
Use VPC's high density signal modules for seamless integration with COTS products. VPC signal modules fit all standard VPC Interconnect Solutions and allow for consolidation of multiple instrument connections within the space of a single or double receiver interface position.
-
product
pH Electrode Holder
PF12
Extension of optek sensor bodies for inline pH measurement in industrial installations of various applications. Commonly available Ø 12mm & 120 mm length pH probes can be used and are positioned at an optimum angle into the process stream.
-
product
Twin columns automated force test stand 36" travel - 20,000 lb
720SN
Sturdy ball screw drives allow for smoother operation and precise positioning. Stands include the touchscreen ComTouch Total Control system. These systems benefit from supporting our universal test software COMTEST.
-
product
Astrosystems Position Sensors
HST-21U Transducer and Encoder
NAI offers resolver-based Astrosystems Absolute Position Sensors for the packaging, material handling, and automated manufacturing industries. Specifically designed for rugged defense and industrial applications, these highly accurate and programmable units feature standard interfaces and rugged designs. They simplify machine set-up, reduce overall costs, extend product life, and provide a very high level of application flexibility.
-
product
CAM/GATE Test Kits
Series 45
The CG Series 45 CAM/GATE linear over clamp kits utilize the same patented “Z” axis motion as our CAM/TRAC® Series products offering precise Z axis linear motion when testing higher point count and finer pitch test centers. By using the Z axis motion, side load of the test probes is minimized thus increasing probe life and performance. The latch assembly engages and disengages when actuating the clamping assembly. The CAM/GATE utilizes a cam roller system for precision guiding and smooth operation and 1.00” push plate movement. The gate assembly is movable to three different positions which allows for the versatility of top side probing, or relocating the frame assembly for PCA’s the have tall components
-
product
Computer Assisted Microhardness System
C.A.M.S.
Newage Testing Instruments, Inc.
The C.A.M.S. concept starts with a Newage microhardness tester (or competitive microhardness tester), such as our MT91 Series or MS-ZH Series with video camera, combined with our software, personal computer and any required accessories, such as a motorized X-Y-Z axis positioning table.
-
product
Process Control Actuators
SM-1700/SM-5000
The SM-1700/5000 Series of rotary actuators are internally geared to produce up to 12,500 ft.lbs. (16,950 Nm) of torque, and offer continuous modulation. They are ideally suited for dampers, vanes, valves and other process control applications requiring exact positioning control.
-
product
Precision Positioning stage
N-661
Physik Instrumente GmbH & Co. KG
Miniature Linear Stage with NEXACT Drive Travel Range 20 mm Self Locking at Rest, no Heat Generation, no Servo Dither Compact Design: 70 x 50 x 20 mm Zero-Wear Piezo Stepping Drive, Ideal for Micro- and Nano-Manipulation Integrated Linear Encoder Option for Highest Accuracy with 20 nm Resolution Two Operating Modes: Continuous Stepping Mode and Continuously Variable, High-Dynamics Analog Mode for 30 pm Resolution** Up to 10 N Force Generation





























