Backplanes
An interconnection structure allowing multiple printed circuit boards to coexist using a single bus.
-
Product
Power Interface Board 3U, 2PSU connectors with AC pins
106PIBM302-9001R
-
The PIB 3U 2 slot has two power connector P47 with AC pins and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
Product
6-slot ATX-supported PICMG Bus Passive Backplane
ATX6022/6
-
*1 PICMG, 4 PCI and 2 ISA*Compatible with AX60501 and AX60530*Supports both AT and ATX power supply
-
Product
ATCA 5U 7 Slot replicated Mesh - dual shelf managers
109ATCA507-3000R
-
The 5U 7-slot ATCA backplane is a Replicated Mesh, compliant to the PICMG 3.0 Rev 3.0 specification. Elma Bustronic’s ATCA backplanes have been simulated and characterized by our signal integrity lab to optimize performance.
-
Product
6U 10-Slot OpenVPX Backplane, Profile BKP6-CEN10-11.2.4-3
1OVX610LX6-1X01R
-
VPX Dual Star with central switches with expansion and control planes, channel Gbaud rate up to 6.25.
-
Product
7U 21 Slot VME64 Low Cost Crate
VME8011
-
The Model VME8011 is a 21 slot VME crate, suitable for 6U x160mm boards, with VME64 compliant backplane. A 1U space is reserved for Fan Unit.The Unit is powered by 100÷230 VAC, 50 ÷ 60 Hz. The Mod. VME8011 has a pluggable Power Supply. The power distribution is +5V@60A, -12V@6 A, +12V@8.9A.
-
Product
cPCI / PXI / PXIe Crates
-
CompactPCI ratified as PICMG 2.0 in late 1995 is an interconnect bus standard for industrial computers, combining a 3U or 6U Eurocard-type card and PCI signaling / protocols via a passive backplane with metric connectors. PXI (PCI eXtensions for Instrumentation) is the application of CompactPCI for measurement and automation systems. PXI uses commercial PC-based PCI bus technology while combining rugged CompactPCI modular packaging with timing and synchronization features in order to provide an optimized basis for complex, rugged, modular instrumentation systems. The PXI standard is governed by the PXI systems Alliance (PXISA)
-
Product
Custom VPX 3U 4Slot
-
4 slot custom 3U VPX backplane with a dedicated interface for IO panel.
-
Product
OnyxFX FlexorSet 4-Ch. 250 MHz A/D w/DDCs, 2-Ch. 800 MHz D/A w/DUC, Int - 3U VPX
Model 5973-313
-
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Four 250 MHz 16-bit A/Ds- Four multiband DDCs- One digital upconverter- Two 800 MHz 16-bit D/As- Extended Interpolation- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 and 3) interface up to x8- User-configurable gigabit serial interface- Optional optical Interface for backplane gigabit serial interboard communication- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-66.4 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- See comparable JadeFX Xilinx Kintex UltraScale FPGA Family:- Model 5983 JadeFX Kintex UltraScale Processor and FMC Carrier 3U VPX- Model 5983-313 JadeFX FlexorSet 4-Ch. 250 MHz A/D w/DDCs, 2-Ch. 800 MHz D/A w/DUC, Int - 3U VPX
-
Product
VME64X 7U 21 slot with P0
101V64XM21-0621R
-
7U VME64x Backplane 21-slot with P0, compliant with ANSI/VITA 1.1-1997, VME extension, and VITA 1.7 Increased Current. The extra 1U provides room for extra power bugs or busbars. Includes termination passive inboard and daisy chain automatic active.
-
Product
Large Board Stencil Printer
MC1200
-
Manncorp's MC1200 SMT large board stencil printer fills application requirements of large-board assemblers with print areas ranging from two feet to nearly four feet in length, making them ideal for LED, backplane and multi-panel assemblies. These big-board printers, priced at one-half to as much as two-thirds less than competing large-board printers, are ideal replacements for slower and less accurate manual printers.
-
Product
CompactPCI Chassis for 3U
-
Advantech offers 3U or 4U height enclosures for 3U CPCI boards, with fan or fanless, and with CPCI legacy backplane or CPCI plusIO backplane.
-
Product
Powered VME64x Crates
-
VME64x represents an extension of the VME64 Standard, VITA 1-1994 and became industry standard in 1996. It defines a set of features that can be added to VME and VME64 boards, backplanes and subracks.
-
Product
BRIC™ - Large PXI Matrix Modules
-
High Density Packaging and Integrated BackplanesWith Pickering's BRIC Large PXI Matrix Modules, the use of high density packaging and integrated backplanes enables a large matrix to be implemented with no user configuration or special matrix expansion kits. These matrices use thru-hole mechanical relays (not surface mount) and can be serviced using standard de-soldering tools simplifying repair and reducing down time. Our BRIC's integrated design ensures high matrix performance with high signal bandwidth and fewer system implementation errors.
-
Product
PCIe to PXI Remote Control Interface Kit
41-924-001-KIT
Remote Control Interface
The kit is supplied with a PCIe card which can plug into any PC PCIe slot, a PXI module for insertion into Slot 1 of a PXI chassis and 3m lead to connect the two parts together. The interface uses a single lane PCIe connection from the PC to provide a software transparent link from the PC PCIe backplane to the PXI backplane. The supplied 3m shielded lead ensures the system has robust operation and an adequate separation distance between the PC and the PXI chassis.
-
Product
F9 Systems CalBlade
-
The CalBlade backplane calibration fixture isdesigned to permit accurate and convenient impedance and transmission measurements of a HM-Zd backplane. The CalBlade is used to calibratethe logic card connector interface to the backplane rather than to the usual far-end of the coaxial measurement cables. Very accurate impedance, skew and propagation delay measurements are possible since parasitic fixturing effects are removed.
-
Product
3U VPX 1 Slot P&G backplane with aperture for VITA 66.4
101V301P06-9X13
-
Power for 3.3V, 5V and 12V per VITA 46, with all rear connectors fully loaded. Use with Elma’s slot-to-slot or slot-to-I/O bulkhead cable products for system development.
-
Product
4U 20-slot Extended Rackmount Chassis
AX61492
-
*Three 5.25" and two 3.5" HDD drive bays*Three 12 cm hot-swap ball-bearing fans*Supports 20-slot backplane*Hot-swap redundant or PS/2 power supply supported
-
Product
PXIe-1088, 9-Slot (8 Hybrid Slots), Up to 8 GB/s PXI Chassis
784782-01
Chassis
PXIe, 9-Slot (8 Hybrid Slots), Up to 8 GB/s PXI Chassis - The PXIe-1088 features an all-hybrid backplane to meet a wide range of high-performance test and measurement application needs. The hybrid connector type in every peripheral slot enables the most flexibility in terms of instrumentation module placement.
-
Product
PXI Prototyping Module, 2-Slot, 25-Pin D-Type
40-225A-302
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
VME64X 6U 12 Slot with P0
101V64XC12-1621
-
6U VME64x Backplane 12-slot with P0, compliant with ANSI/VITA 1.1-1997, VME extension standard. Includes termination passive inboard, daisy chain automatic active, and power bugs on top and bottom of slots.
-
Product
PXI FlexRIO Coprocessor Module
Module
PXI FlexRIO Coprocessor Modules feature high-performance FPGAs that add signal processing capability to PXI systems. These modules leverage the latest FPGAs from Xilinx, streaming technologies such as PCI Express, and NI Peer to Peer Streaming for high-bandwidth data communication with other modules over the backplane. When paired with another PXI device, such as a PXI Vector Signal Transceiver, PXI FlexRIO Coprocessor Modules provide the additional FPGA resources required to run complex algorithms in real-time.
-
Product
JadeFX Kintex UltraScale Processor and FMC Carrier - 3U VPX
Model 5983
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family BrochureVITA-57.4 HSFC FMC+ site offers access to a wide range of possible I/O- Supports Xilinx Kintex UltraScale FPGAs- 9 GB of DDR4 SDRAM- On-board GPS receiver- PCI Express (Gen. 1, 2 and 3) interface up to x8- User-configurable gigabit serial interface- LVDS connections to the Kintex UltraScale FPGA for custom I/O- Optional optical interface for backplane gigabit serial interboard communication- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-66.4 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available
-
Product
VME / VME64x Chassis
-
Hartmann Electronic is an industry leader in the designing, manufacturing and production of backplane technology, including VME and VME64x. Over the evolution of its near 40 years of existence, VME-bus has become a worldwide standard and is still used in a wide variety of applications across many different markets.
-
Product
PXI Prototyping Module, 1-Slot no Connector
40-225A-001
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
VME64X 6U 5 Slot no P0
101V64XC05-0620
-
6U VME64x Backplane 5-slot without P0, compliant with ANSI/VITA 1.1-1997, VME extension standard. Includes termination passive inboard, daisy chain automatic active, and power bugs on top and bottom of slots.
-
Product
6U cPCI Power Backplanes
-
CompactPCI bus is compatible, in terms of electrical specification, with the PC world’s PCI bus. The mechanical specifications were adapted to the commonly used Euro-card plug in systems for 19″ racks.
-
Product
AdvancedTCA, Type 11A, 13U 19" Vertical, DC
11A14FGCD8Y4VNXX
-
Elma's ATCA, DC, 13U vertical enclosures with backplane 14-Slot Dual Star or Mesh backplane, shelf management, and options. PEMs with availability (99.999%). 19" rackmount vertical ATCA chassis for carrier-grade applications.
-
Product
3U CompactPCI Serial 4-slot SSR w/o RTM w/ Ethernet
1CPCIS-304-R200
-
3U CompactPCI Serial Backplane with 4 CompactPCI S.0 slots, system slot right, without rear IO : 1x CompactPCI S.0 CPU slot, 3x CompactPCI S.0 peripheral slots, without connectors for RTMs (RearTransition Modules), Ethernet full mesh.
-
Product
19" Rackmount
-
Packaging solutions engineered using modular design methodology providing countless combinations of card slot count, backplane architecture, power, cooling, height and depth leading to reduced cost, lead-time and program risk. Standard options from 1U through 14U to house: VME, VME64x, OpenVPX, CompactPCI/CompactPCI-Serial and AdvancedTCA architectures. From commercial grade to MIL-STD applications, Elma’s packaging solutions provide your systems the protection you need.
-
Product
Other Eurocard Backplanes
-
OpenVPX, CompactPCI, VME, and VME64x are open standard backplane architectures commonly used in Eurocard systems. (For OpenVPX products, see the Pixus OpenVPX section.) Pixus has a wide range of CompactPCI, VME, VME64x, and other backplanes available off-the-shelf.
