Voltage
The tension of an electromotive force.
-
Product
High Voltage 9-Pin D-Type Connector & Cable Accessories
-
The High Voltage 9-Pin D-Type connector is used on high voltage PXI and LXI switching products to provide a high voltageconnector solution. Connection solutions for modules with Standard Voltage Rating D-Type connectors are also available.
-
Product
Thermal Voltage Converter
1395B
-
The 1395B TVC. Has better thermal stability than it's predecessor. Measuring ac voltages between 20 Hz and 100 MHz with increased accuracy and reliability. The 1395B can be used as a primary ac voltage standard and/or standard for the calibration of ac calibrators and voltmeters.
-
Product
LXI High Voltage Matrix 2-pole 300x2
60-310-302
-
The 60-310 is a 2-pole Matrix Module available in 300x2, 200x2 and 100x2 formats. It is capable of cold switching 1000VDC and has a maximum carry current of 1A. It is designed for high voltage applications including circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
-
-
Product
High Voltage Power Supplies
-
Trust a high voltage power supply provider with 40-plus combined years of experience. Advanced Energy’s HiTek Power and UltraVolt product lines feature hundreds of units, options, and accessories to meet your application needs.
-
Product
NI-9202, ±10 V, 10 kS/s, 24-Bit, 16-Channel C Series Voltage Input Module
784400-01
-
±10 V, 10 kS/s, 24-Bit, 16-Channel C Series Voltage Input Module - The NI-9202 has excellent flexibility to meet the needs of your applications. The module has 16 simultaneous sampling, differential input channels to create large, distributed systems in a rugged form factor. It also has configurable filters to eliminate noise in your system while maintaining low-latency to be used in control systems.
-
Product
High Voltage 50 Ω Pulse Generator
TLP-4010C
-
High Power Pulse Instruments GmbH
*Wafer and package level TLP/VF-TLP/HMM testing*Ultra fast 50 Ω high voltage pulse output with typical 100 ps rise time*Built-in HMM (IEC 61000-4-2) pulse up to ±10 kV*High pulse output current up to ±40 A*High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)*6 programmable pulse rise times: 100 ps to 50 ns*8 programmable pulse widths: 1 ns to 100 ns*Optional pulse width extender increases pulse width up to 1.6 µs in 68 programmable steps*Fast measurement time, typically 0.2 s per pulse including one-point DC measurement between pulses*Efficient software for system control and waveform data management*The software can control automatic probers for fast measurement of complete wafers*High performance and high quality components
-
Product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-02 And WMA-02LF
-
The Falco Systems WMA-02 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 4mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-02LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.2mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Product
Standard Voltage 50-Pin D-Type Connector & Cable Accessories
-
The Standard Voltage 50-Pin D-Type connector is used on PXI switching products to provide a medium density connector solution. Connection solutions for modules with High Voltage Rating D-Type connectors are also available.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-110-HI
-
The 40-230-010-HI (PXI) and 42-230-010-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 2.5Ω and 31.5Ω with 0.125Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-120-HI
-
The 40-230-120-HI (PXI) and 42-230-120-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3Ω and 472Ω with 0.125Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Voltage Controlled Linearized Attenuators To 16 GHz
-
Pulsar's voltage controlled, PIN diode linearized attenuators are available from 0.25-16 GHz with attenuation ranges of 32 and 64 dB. Each model includes an integrated linearizer, and a driver that controls the attenuation level. This design results in transient free switching between attenuation levels as opposed to the spurious outputs that result when an attenuation value is switched either on or off by a direct digitally controlled attenuator. Transfer function is 8 dB / Volt.
-
Product
Series Voltage References
-
Analog Devices offers a broad line of series voltage references with low dropout, low power, and excellent line regulation. These devices are voltage references that are functionally similar to a three-terminal regulator. Some series voltage references are designed to also operate in shunt mode by biasing the output pin and leaving the input pin open circuit. Series mode voltage references have the advantage that they draw only load and quiescent current from the input supply.
-
Product
PXI/PXIe High Voltage Multiplexer, Dual 23-Channel, 1-Pole
40-321-108-HI
-
The 40-321-108-HI (PXI) and 42-321-108-HI (PXIe) are dual 23-channel 1-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
sbRIO-9215, Non-Enclosed, ±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
781029-01
-
Non-Enclosed, ±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The sbRIO‑9215 performs differential analog input. The sbRIO‑9215 contains NIST‑traceable calibration, a channel‑to‑earth ground double isolation barrier for safety and noise immunity, and high common-mode voltage range. Non-enclosed modules are designed for OEM applications.
-
Product
Low Voltage Test & Measurement
-
Low voltage testing is able to catch errors such as shorts and opens by applying current to a wire and measuring the voltage. The wire will have a current affected by several factors including resistance and components. If the wire is connected correctly, the test will read low resistance. That means current is flowing through the wire as expected and reaching the required connections. If the tester reads high resistance it means something is impeding the current from reaching its destination. This could be caused by a number of causes.
-
Product
Voltage Meter
MN3I
-
М-module МН3И is a mezzanine module designed to measure the instantaneous voltage value of high-frequency signals via 3 galvanically isolated channels from each other, control circuits and crate frame.
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-325-HI
-
The 40-230-325-HI (PXI) and 42-230-325-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3Ω and 13.6kΩ with 4Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
NI-9238, ±500 mV, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
783311-01
-
±500 mV, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9238 performs differential analog input. The measurement range is compatible with many low-voltage sensors such as current shunts and current transducers in high-current applications. When used with higher-voltage C Series Voltage Input Modules, the NI‑9238 can measure power and energy consumption for applications such as appliance test, industrial machine monitoring, power quality analysis, phasor measurements, and harmonic analysis.
-
Product
Voltage Input0 to 2.5/10/25V
TGPR-0704
-
Voltage input data logger that is housed in a robust, waterproof (IP68) rated case.The TGPR-0704 can be used to record the output from a number of industry standard sensors. Common applications include pressure and windspeed monitoring.
-
Product
Voltage Rectifier
-
A voltage rectifier, designed and manufactured by Monex GeoScope Pty. Ltd., has been added to the terraTEM suite of products. The voltage rectifier has been designed to provide 6 kW, 120 V, 50 A output and is the ideal rectifier to guarantee the necessary stable, ripple free current for the full range of Monex GeoScope’s transmitters. This includes the internal transmitters for the terraTEM24 (50 A, 120V), terraTEM (15 A, 24 V) and the terraTX-50 external transmitter (50 A, 250 V). In addition, the voltage rectifier outputs a clean, filtered 24 V suitable for powering either the terraTEM24 console or terraTX-50 console electronics. And the output stability of the voltage rectifier is not disturbed by the fast turn-off times available on the Monex GeoScope transmitters.
-
Product
Stand Alone Low Voltage Tester
Model 256/PC
-
Internal Memory: 8 program locations without test point labels or 2 program locations with test point labels. Removable Memory: 16 program locations without test point labels, or 4 program locations with test point labels.
-
Product
1,000 Watt AC/DC (High Voltage Output) Power Supplies
56XS2
-
NAI’s 56XS2 is a conduction-cooled, 1,000 Watt AC/DC Power Supply that converts a 3-phase, AC input into a single HIGH VOLTAGE +270 VDC output at 1,000 Watts.
-
Product
PC Controlled Low Voltage Tester
Cablescan S32
-
The Cablescan S32, with a 32-board Expansion Cabinet, may be ordered with 1 to 32 low-voltage 128-point scanner boards. Fully loaded with scanner boards, this tester provides 4096 test points.
-
Product
Non Contact Voltage Detection
-
Our range of Non Contact Voltage Detectors offer a safe and accurate method of checking for voltage present on a conductor. With audible and visual indication, our range offers total confidence when checking cables for live voltages
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-114-HI
-
The 40-230-114-HI (PXI) and 42-230-114-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 2.5Ω and 470Ω with 2Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Non-Contact Voltage Tester
1LAC II
-
The Fluke 1LAC II Non-Contact Voltage Tester is easy to use – just touch the tip to a terminal strip, outlet, or supply cord. When the tip glows red and the unit beeps, you know there's voltage present. Electricians, maintenance, service, safety personnel, and homeowners can quickly test for energized circuits in the workplace or at home.
-
Product
NI-9215, ±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
783739-01
-
±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9215 performs differential analog input. The module contains NIST-traceable calibration, a channel‑to‑earth ground double isolation barrier for safety and noise immunity, and high common-mode voltage range. It is also offered in two connectivity variants: 10‑position screw terminal or BNC.
-
Product
Power Supply Voltage Fluctuation Simulator
SG Series
-
Simulator to reproduce DC supply voltage variations phenomena in the vehicle environment for evaluating immunity of automotive electronics. This simulator can perform various tests against voltage variations required by ISO 16750 and other international standards. Please contact us for voltage variations testers to perform testing to manufacturers' private standards.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-113-HI
-
The 40-230-113-HI (PXI) and 42-230-113-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 2.5Ω and 239Ω with 1Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
