Voltage
The tension of an electromotive force.
-
Product
Voltage Indicators
-
Available with a digital readout or a simplified LED display Seaward's specialist range of voltage testers have the versatility and durability to cope with all types of user demands.
-
Product
High Voltage Differential Probe
DP750-100
-
Shenzhen Micsig Instruments Co., Ltd.
*The leads and probe are with shielded design, interface ends are integrated in a compact box, no need to twist the cables, leads to a lower noise floor and has less interference. *Support one-press Zero calibration and automatic overrange alarm.*Directly powered by Micsig UPI interface, realise auto scaling setup, can also powered by oscilloscope via USB cable.
-
Product
Multifunction Voltage and Current Calibrator
MC140i
-
Multifunction calibrator MC140i is ideal for calibration of voltmeters, ammeters, DMMs and panel meters. AC/DC voltage 1uV to 1000V. Current 50uA? to 1000A using test coil. Deviation control along readout. 0.0035% basic dc accuracy. 0.03% basic ac accuracy. Supplied with RS232 interfaces. UKAS/NIST Traceable
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-346-HI
Programmable Resistor Module
The 40-230-346-HI (PXI) and 42-230-346-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4Ω and 5.806MΩ with 8Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
M-LVDS (Multi-Point Low Voltage Differential Signaling)
-
M-LVDS (multipoint low voltage differential signaling) is a multipoint high speed differential electrical interface with support for up to 32 nodes. Analog Devices M-LVDS products offer the industry’s highest ESD performance transceivers with high noise immunity receivers and extended common-mode range. These products are ideal for applications where designers need to transmit at data rates up to 100 Mbps or 250 Mbps to multiple nodes.
-
Product
Bench/System Higher Voltage DC Power Supply With Linear Regulation. Single Output 90 Watts, 120V Or 250V, With/without Remote Interfaces
PLH Series
-
Single output 120V 90W or 250V 94WLinear regulation - for the best performanceUltra-compact design - uses up less spaceTrue Analogue controls - for ease of useS-Lock function - instantly lock settingsV-Span function - customize the voltage rangeLow current range and current meter averagingDC output switches and "view limits" buttonSelectable remote sense terminals
-
Product
C Series Voltage Input Module
Module
The C Series Voltage Input Module helps you work with voltage measurement applications. This module features isolation to separate channels from each other, from COM, or from earth ground for safety, noise immunity, and high common-mode voltage range. The module features up to 100 V of overvoltage protection for errant signal connection or unexpected outputs to the individual channels. You can use included options such as configurable input ranges, output channels, various connectors, and enclosed or non-enclosed modules.The C Series Voltage Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
High Speed High Voltage Amplifier
WMA-300
-
The WMA-300 is a high voltage, wide bandwidth laboratory amplifier. Its high output voltage, current and wide bandwidth have been designed to serve the needs of a wide variety of high-tech experiments. The WMA-300 can be used for MEMS actuation, EO-modulators, PZT (piezo) positioners, ultrasonics, and many other applications. Two WMA-300 amplifiers and a WMA-IB-HS phase inverter - buffer can be used to double the output voltage.
-
Product
LXI High Voltage Switching - 4-Bank, 1-Pole, 12:1 Multiplexer Plugin Module
65-231-706-HI
Multiplexer Module
The 65-231-706-HI plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 7 kV. Multiplexers are created by populating the 65-200-002 scalable chassis with multiplexer plug-in modules that provide access to the Channel and Common signals on 51-pin front panel connectors.
-
Product
Additional Products: Standard Voltage 9 Pin D-Type Cables - Connector to Connector
-
The connector to connector cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
HV DC Voltage Generators
-
Fivestar HV Testing Equipment Co., Ltd.
HV DC voltage generators are used to generate high voltage DC test voltages for routine, type and development test on components and complete systems found in electrical power supply systems and operating on DC voltage (HV transmission systems etc). There are K and M series, and available for indoor and outdoor.
-
Product
Standard Voltage 50 Pin D-Type Cables - Connector to Connector for Pickering
-
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a standard voltage 50-pin D-type connector.
-
Product
Two-Pole Voltage Tester
P-4
-
Sonel P-4 is reliable, particularly durable and safe 2-pole testers, which enable testing voltage, circuit continuity and phase sequence. It has been designed for use in extreme conditions both in industry and commercial applications. Advanced technology, a high level of safety and user-friendliness are the key features of the P-line voltage testers.
-
Product
High-Voltage Differential Probe, 70 MHz
N2891A
High Current Probe
Use the N2891A 70-MHz high-voltage differential probe to make safe and accurate floating measurements with an oscilloscope. The N2891A differential probe allows conventional earth-grounded Keysight oscilloscopes to be used for floating signal measurements of up to ±7000 V of differential and common mode voltage.
-
Product
5k Voltage Probe (set Of 3)
5KVPSet
-
5KVPSet is a set of three voltage probes that allow direct connection to up to 5,000 Vrms 3 phase power.
-
Product
Contact Voltage Detectors & Phaser
-
*For use on uninsulated overhead conductors*Audible and visual alert when absence of voltage is detected*Models available with different voltage ranges
-
Product
Full Range Auto-Ranging Voltage Indicator
ARVI
-
This smart new-generation instrument makes hot-line voltage testing easier than ever. Its state-of-the-art electronics eliminate the need for a selector switch.
-
Product
PC Controlled Low Voltage Tester
Cablescan S32
-
The Cablescan S32, with a 32-board Expansion Cabinet, may be ordered with 1 to 32 low-voltage 128-point scanner boards. Fully loaded with scanner boards, this tester provides 4096 test points.
-
Product
High Voltage Probes To Measure Primary Waveforms With A Power Analyzer
Volt Litewire
-
The Litewire is a true RMS meter designed for use by electric utilities to sense currents or voltage waveforms from the primary side of their distribution networks.
-
Product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-01 And WMA-01LF
-
The Falco Systems WMA-01 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-01LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Product
VOLTAGE TRANSFORMERS
-
Designing & manufacturing a range of high quality, voltage transformers in three different frame sizes for both measuring and protection duties. Transformers which are designed to comply with the requirements of IEC 61869-3 or other international standards as required can be supplied to satisfy most Low Voltage applications.
-
Product
NI-9264, 25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module
785190-02
Voltage Output Module
25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module - The NI‑9264 is a simultaneously updating analog output module that accommodates higher‑channel‑count systems. Higher density modules conserve chassis space, which leaves room for other measurement types. Each channel has its own digital‑to‑analog converter. The spring-terminal version of the NI‑9264 uses a 36‑position connector for the output channels, and each channel has a ground connection.
-
Product
3 Phase Voltage Transducer
-
Converts a three phase, 600 VAC, 50/60 Hz power system to three proportional 0 to 5 volt DC outputs.
-
-
Product
AC/DC Voltage Detector (CONTACT TYPE)
LVD-20
-
Standard Electric Works Co., Ltd
Contact type. LED indication and audible alarm sound when voltage is present. Designed for AC/DC voltage detection. Used for bare wires or conductors. Self-test function. For indoor use only. Low power consumption. Light weight and compact.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-030-HI
Programmable Resistor Module
The 40-230-030-HI (PXI) and 42-230-030-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3.5Ω and 6.97kΩ with 0.125Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Programmable Voltage Reference Plug-In
ProDAQ 3202
-
The ProDAQ 3202 voltage reference card is used in the ProDAQ 3180 ultra-performance motherboards and LXI function card carriers. The ProDAQ 3202 voltage reference card is plugged directly onto the motherboard or carrier and can distribute the reference voltage to all ProDAQ function cards via two signal lines. This allows the distribution as a differential signal to overcome possible noise pick-up.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-224-HI
Programmable Resistor Module
The 40-230-224-HI (PXI) and 42-230-224-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 3Ω and 6.97kΩ with 2Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
sbRIO-9205, Non-Enclosed, ±10 V, 250 kS/s, 16-Bit, 32-Channel C Series Voltage Input Module
784787-01
Voltage Input Module
Non-Enclosed, ±10 V, 250 kS/s, 16-Bit, 32-Channel C Series Voltage Input Module - The sbRIO‑9205 performs single-ended or differential analog inputs, with four programmable input ranges for each. It is an effective combination of channel count and speed at a low price for an economical multifunction system. You can choose from four programmable input ranges. To protect against signal transients, the sbRIO‑9205 includes up to 60 V of overvoltage protection between input channels and common (COM). In addition, the sbRIO‑9205 also includes a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and high common-mode voltage range. It is rated for 1,000 Vrms transient overvoltage protection. Non-enclosed modules are designed for OEM applications.
-
Product
High Voltage 37 Pin D-Type Connectors for Pickering Products
-
The connectors below are suitable to use with Pickering cards and modules that utilize a high voltage 37-pin D-type connector.
