Switching Matrices
See Also: Switching, Switching Matrix, High Voltage Switching, Multiplexers, General Purpose Switch, Switch Matrix
-
product
Ultra Pure Vacuum Switch (longbody, NEMA 4)
W117LV
The W117LV NEMA IV Rated Ultra Pure Stainless Steel Vacuum Switches have all welded stainless steel interiors which are Helium leak checked to pass 4 x 10-9 Std cc/sec. These are the weather-proof, liquid-resistant version of the W117V suitable for outside applications or in areas of condensing humidity.
-
product
RF SPDT PXI Switch Modules
Pickering's RF SPDT PXI Switch Modules are capable of providing economic switching for frequencies up to 6 GHz. Our other PXI RF options include RF matrices and RF multiplexers. For higher frequency applications or applications requiring high performance levels, please take a look at our microwave switching modules.
-
product
RF Capacitance Level Switches
ABB's RF Capacitance level switches feature one-step external calibration, immunity to material build-up, and a wide selection of probes for even the most challenging applications from low dielectric bulk solids to sticky slurries.
-
product
LXI High Voltage Switching - 1-Bank, 1-Pole, 48:1 Multiplexer Plugin Module
65-231-900
The 65-231-900 plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
product
Coaxial Switch, DC to 4 GHz, SPDT, 75 Ohms
8762F
The Keysight 8762F brings a new standard of performance to 75-ohm coaxial components. Designed for ATE switching systems, the Keysight 8762F offers the performance demanded by the cable television distribution equipment and communications equipment industries. It gives the ATE system designer of telecommunications and cable distribution equipment the tools to design reliable, high performance switching interfaces. The Keysight 8762F uses a mini 75-ohm SMB connector for the coaxial interface. The mini 75-ohm SMB connector is designed to terminate RG-179 75-ohm coaxial cable. The Keysight 8762F is designed to work in virtually any system due to the range of voltage options covering 4.5 V to 30 Vdc available for activating the switch solenoids. The standard configuration of the switch includes solder terminals.
-
product
PXI Single 2 x 2 Insert/Bypass Switch FC/APC
40-860-012
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
PXI-2535, 544-Crosspoint, 1-Wire PXI Matrix Switch Module
778572-35
544-Crosspoint, 1-Wire PXI Matrix Switch Module—The PXI‑2535 is a high-density 4x136 PXI matrix switch module that is ideal for routing low-power DC signals in validation test systems of mass produced devices such as semiconductor chips and printed circuit boards (PCBs). Featuring field-effect transistor (FET) relays, the PXI‑2535 offers unlimited mechanical lifetime and switching speeds up to 50,000 crosspoints/s. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
product
Test Switch
The W3TS Test Switch, a miniature knife blade switch (5/8 inch centers including barrier) with #10-32 stud terminals, is available in three types: Basic Switch, Short-Circuiting Switch (Shorting Switch), Test Jack Switch
-
product
3U OpenVPX Ethernet Switch and Multifunction I/O Board
68G5E
The 68G5E is a 3U OpenVPX board that is configured with an Ethernet Switch module (choose the ES1, 12-Port GbE Cu legacy unmanaged Ethernet Switch, or the ES2 16-Port Cu GbE managed Ethernet Switch with optional 4x 10GBASE-SR 850 nm multimode Fiber Optic interface) and provides additional support for one NAI smart I/O and Communications function module. Uniquely designed, the 68G5E provides ‘independent’ Ethernet Switch capabilities and can operate as a MFIO board end point with access via the 1 x1 PCIe and/or 1x 10/100 Ethernet motherboard Control Port which hosts the NAI Ethernet Protocol Server/Listener application for direct GbE MFIO control. Ideally suited for rugged Mil-Aero applications, the 68G5E delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
product
Optical Fiber 2×2 Switch
OFSW - 2 × 2
Hangzhou Huatai Optic Tech. Co., Ltd.
OFSW-2 × 2 is a 2 × 2 prism optical switch. It can support 2 optical fibers input and 2 fiber output, channel switch. Wide operating wavelength range, low insertion loss and speedy switching rate, can use network trends configuration, network monitor and lab application.
-
product
MEMS Fiber Optical Switch at Single Mode 1315nm Type-A with LC/PC Connector
SUN-MS-1x8
Guilin GLsun Science and Tech Group Co., LTD
Fiber Configurations 1x8 MEMS Fiber Type SM, 9/125 umTest Wavelength 1310/1550 nm Operating Voltage 2.5VSwitch Type Non-latching Fiber Length 0.5m±5cmConnector TTL/UART Tube Type 900 umOperating Temperature -5°C~ +70°C Storge Temperature -40°C ~ +85°C
-
product
LXI High Voltage Switching - 6-Bank, 1-Pole, 8:1 Multiplexer Plugin Module
65-231-909
The 65-231-909 plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
product
PXI Switched Guard Reed Relay Module, 13x SPST
40-121-002
The 40-121-002 provides 13x SPST switches in a single slot PXI module and designed to provide an isolation resistance in excess of 1013Ω. It has been designed to ensure high isolation resistance through the use of switched guards, making it ideal for low level measurements and semiconductor test.
-
product
VXI Switching
The Aerospace and Defense industries were early adopters of modular test platforms. One of the first successes was VXI test systems and VXI switching. They served these industries very well for more than 20 years. Now, as VXI test systems become obsolete, test systems developers are looking to PXI as the next generation modular test platform for their industries. We offer a few different references to help you in making a switch to PXI.
-
product
SS Body Pressure Switch (longbody, NEMA 4)
P117LG
The P117LG NEMA 4 Stainless Steel Pressure Switches are the weather-proof, liquid-resistant version of the P117G. The NEMA 4 rating makes these rugged switches suitable for outside applications or in areas of condensing humidity. Unlike the P117G, the P117LG set point is factory set to customer specification and is non-adjustable.
-
product
PXI 5A Fault Insertion Switch 10-Channel
40-196-001
The 40-196 is a 10 Channel 5A Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Shorting relays on each channel enable UUT signals to be subjected to external user applied fault conditions or to be shorted to the adjacent signal in the same channel. Relays in line with the signal allow open circuit conditions to be simulated on either side or both sides of a channel signal pair. The switching topology of the 40-196 allows channels to be interconnected so that complex fault insertion systems can be constructed.
-
product
20 x GB ETH Switch
SL4-TUBA
SL4-TUBA is a peripheral slot card for CompactPCI® Serial systems. The board is equipped with a modular Gigabit Ethernet switch fabric up to 20 ports.
-
product
PXI Single 24x8 Matrix, 1 Pole Switching
40-521-021
An ultra high density matrix module is configured as a 24x8, this range is availablein a choice of reed relay formats: 1-pole (shown here), 2-pole and 1-Pole screened. The screenedversion is suitable for switching signals up to 50MHz. Typical applications include signal routing in Functional ATE and data acquisitionsystems. These PXI matrix cards are constructed using high reliability RutheniumElectro-Plated Reed Relays, offering >10e8 operations to give maximum switchingconfidence with long life and stable contact resistance.
-
product
L20 Series Side Mounted Kynar Plastic Liquid Level Switch
L20-17-S1-17-NO
The L20 Series Side Mounted Kynar Plastic Liquid Level Switches come with a 1/2" NPT fitting and are typically used with solvents and certain bases. The side mount provides added versatility, allowing the switch to be used as a high or low level indicator, and plastic body provides use up to 100 PSI.
-
product
Single Mode Low Loss All Optical Switch From 8x8 To 192x192 Ports
SERIES 6000
The Polatis Series 6000 Network Optical Switch is a high-performance, fully non-blocking all-optical matrix switch available in sizes from 8x8 up to 192x192. It is designed to meet the highest performance and reliability needs of the most demanding applications with exceptionally low optical loss, compact size, low power requirements and fast switching speeds. With support of Software-Defined Networks (SDNs) via an embedded NETCONF and RESTCONF control interfaces, the Series 6000 enables extremely low latency for time-critical traffic required for new virtual cloud services in hybrid packet-optical data centers. The Series 6000 is based on Polatis’ patented DirectLight® optical switching technology that has been proven in the most challenging data center, telecom and defense applications and is also used by major network equipment manufacturers to automate testing of optical components and subsystems.
-
product
Safety Door Switch with Key
SG-B2 Series
Panasonic Industrial Devices Sales Company of America
These products feature key-based operation for worker protection in larger areas that could be hazardous. The SG-B2 Series Safety Door Switch and the SG-D1 Series Key Selector Switch can be used in tandem to add multiple layers of protection.
-
product
LXI High Voltage Switching - 6-Bank, 1-Pole, 6:1 Multiplexer Plugin Module
65-231-911
The 65-231-911 plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
product
PXI/PXIe MEMS Optical Switch, Dual Insert/Bypass
40-860A-022
The 40/42-860A-022 is a PXI/PXIe dual insert/bypass switch with FC/APC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
product
PXI/PXIe Fault Insertion Switch, 64-Chan 2A, N/C Through Relays, Fault Buses on M & U
42-190C-112
The 40-190C-112 (PXI) and 42-190C-112 (PXIe) are fault insertion switches with 64 channels. They are part of a range of modules available with 74, 64 or 32 channels and are primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
product
L-Band Matrix Switches
Quintech Electronics and Communications Inc.
L-Band RF Signal Management.
-
product
Noise Receiver Modules And Noise Switching Modules
MT7553 Series
Noise Parameters are the non-50Ω extensions of Noise Figure, and are an important modeling and model validation tool to understand how a device-undertest’s performance changes as a function of source impedance. Noise Parameter measurements are typically performedusing a Vector Network Analyzer (VNA) to measure the S-Parameters of the DUT, and a Noise Analyzer (either Noise Figure Analyzer NFA or Spectrum Analyzer SA) to measure the noise power of the DUT. Noise parameters are calculated from a combination of knownsource impedances, S-parameters and noise powers.
-
product
Float Switches
B/W Controls has been manufacturing float based tilt switches for decades. Simple tilt position is all that is needed to actuate a B/W relay and or signal a control panel of the alarm.
-
product
Photoelectric Switch
PE3
● Compact size for 13.5(W)*25.5(H)*32.0(L)● A wealth of models ideal for limit control, counting control, and other applications.● Sensing distance of 5~60cm for Diffuse reflective models, 1M~2M for Retro reflective models and 1M~5M for Through beam models.
-
product
DVI Video Matrix Switch with Audio Option up to 32x32
SM-nXm-DVI-LCD
The VEEMUX® DVI Video Matrix Switch routes video from up to 32 single link digital DVI video sources (computers, DVD players, satellite receivers, etc.) to up to 32 displays (LCD monitors, Plasma screens, DLP HDTVs, projectors, etc.) and stereo audio speakers (with audio option).
-
product
Vertical Brass/Buna Temp Level Switch
L10
The L10 Series Vertical Mount Brass Buna Temperature-Level Switches are highly versatile, providing the end-user the ability to control both temperature and liquid level within an application. The buna float can be used in numerous liquids and can survive up to 230 in oil. The internal thermostats are available from 100 to 225 in 25 increments, with special temperatures available for O.E.M. customers.
