Automotive
Car industry or about cars.
See Also: Vehicle, V2X, Truck, Electric Vehicle, Car, Autonomous Vehicle, Autonomous Underwater Vehicle
-
product
PXI/PXIe Battery Simulator Module, 2-Channel, Simplified Current Sink, 750 V Isolation
41-752A-903
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
product
Low-Power General Purpose FPGA
Certus-NX
*Up to 39K logic cells, 2.9 Mb embedded memory, 56 18 x 18 multipliers, 192 programmable I/O, one lane of 5 Gbps PCIe, two lanes of 1.25 Gbps SGMII, two ADCs (each 12-bit, 1 MSPS).*Packages as small as 6x6 mm, and in ball-pitch options of 0.5 and 0.8 mm.*Power modes – User selectable Low Power vs. High Performance modes, enabled by FD-SOI programmable back-bias.*Design security – ECDSA bitstream authentication, coupled with robust AES-256 encryption.*Instant-on configuration – I/O configures in 3 ms, and full-device as fast as 8 ms.*Available in Commercial, Industrial and Automotive (AEC-Q100 qualified) temperature grades.
-
product
Power Management and System Basis ICs
ST provides a large selection of Power Management ICs and System Basis Chips (SBC) specifically designed for automotive electronic systems.
-
product
Arduino CAN Shield
IFB-10003-ANP
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
product
GNSS ICs
Teseo III, the latest generation of ST's GNSS ICs, offers reduced power consumption and carrier-phase tracking, allowing higher accuracy for automotive applications.
-
product
Striplines / TEM-Cells
Open, unsymmetrical 50 Ω stripline for automotive immunity testing of components.
-
product
PXIe-8623, 4-Port, 100/1000BASE-T PXI Automotive Ethernet Interface Module
787992-01
PXIe, 4-Port, 100/1000BASE-T PXI Automotive Ethernet Interface Module - The PXIe-8623 is a 100/1000BASE-T unshielded twisted pair (UTP) PXI Automotive Ethernet Interface Module that helps you develop applications with the NI‑XNET driver. With the PXIe-8623, you can develop applications that require Ethernet to test and validate automotive electronic control units (ECUs). The PXIe-8623 provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboard hardware timestamping and can act as up to four separate 802.1AS masters or slaves, making synchronization with an external network as well as the rest of a PXI system possible. Additionally, the PXIe-8623 features LEDs on the front panel to help you monitor the network link and activity.
-
product
Energy Storage
JRT Photovoltaics GmbH & Co. KG
The demand for energy storage systems based on lithium-ion battery technology is rapidly growing, both in the automotive industry and for stationary applications. Jonas & Redmann offer innovative, mature production facilities for all steps for the production of lithium-ion energy storage devices, starting with battery cell production to the assembly of the battery modules.
-
product
LED Drivers
ST offers a large portfolio of energy-efficient DC/DC powered LED driver ICs for general lighting, display LED backlighting, automotive exterior and interior lighting, RGB and monochromatic LED drivers for signage and traffic signals.
-
product
NI-9221, ±60 V, 800 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module
783732-01
±60 V, 800 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module - The NI‑9221 performs single-ended analog input. The wider voltage range makes this module well suited for industrial-level, automotive, or even smaller-cell battery measurements. There are two connector options for the NI‑9221: a 36‑position spring‑terminal connector and a 37-position D‑SUB connector.
-
product
PXI Voltage Amplifier D Type Connector
41-650-001
A 5 channel voltage amplifier ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test.
-
product
Appearance
Konica Minolta Sensing Americas, Inc
For maximum impact, the surface quality of an automotive paint finish must instantly produce an appealing visual sensation for the customer. A high-quality paint finish is not only described by color but also brilliance (“gloss”) and smoothness, often referred to as DOI (Distinctness of Image). This can only be achieved if the overall surface finish displays both high QUALITY and HARMONY.
-
product
O.N.E. for Development
"O.N.E. for Development" goes beyond pure data exchange features of a generic middleware. The platform provides:- Deterministic data exchange- Distributed scheduling- Native tooling- Cloud support- Real-time capability- Many HW/SW InterfacesIt has been extensively used in in testing & validation applications within aerospace and automotive industries.
-
product
Development Tools
Automotive Ethernet (BroadR-Reach) development tool for bidirectional media conversion and coupling (Ethernet Tap) from Automotive Ethernet (BroadR-Reach). In addition, the Media Converter BroadR-Reach can diagnose connection quality, status, and errors .
-
product
Low-Voltage Tester
69127
Device for checking live 6-24V, AC or DC circuits.Tests for shorts in automotive and truck electrical systems, motor field coils, radio and low-voltage circuits, ground circuit of all lamps, wiring, fuses, etc.Bulb in handle glows when circuit is complete (bulb included).Pointed 3-3/4'' (95 mm) probe makes checking easier.Deluxe 3.5'' (89 mm) long handle with nylon top holds replaceable bulb.36'' (914 mm) test lead with alligator clip.Replacement bulb: Cat. No. 69130
-
product
Photometer
Optronik Line DSP 200
Instrument Systems Optische Messtechnik GmbH
DSP 200 offers outstanding sensitivity and stability for precise measurements even at very low illumination levels. The instrument meets, of course, all requirements of the newest standards, like EN 13032-1 and DIN 5032-7 (2017). A low-noise photo diode with V(lambda)-filtering and optimized electronics provides for a broad dynamic range from 0.1 mlx to 200 klx. At the same time the very high local resolution allows an accurate determination even of high gradients when measuring headlamps. Therefore, the DSP 200 is suitable for all automotive and traffic applications, as well as for flashlights and for measurements of all pulse width modulated light sources.
-
product
PXI/PXIe Battery Simulator Module, 6-Channel, 1 KV Isolation
41-752A-101
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture. The 750 V or 1 kV isolation barrier (version dependent) allows the module to be used as a lower power version of a battery stack, representative of those used for vehicle propulsion.
-
product
Sand and Dust Environmental Test Chamber
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Sand and dust test chamber is suitable for all kinds of automotive parts dust-proof, dust resistance test. Test components including automotive lights, instrumentation, electrical cover, switch system, door lock, etc., and test its sealing performance. Besides, it also has view window with illumination.
-
product
RH850 Family (Automotive Only)
RH850/D1x
The RH850/D1x microcontroller provides the biggest MCU lineup for various instrument cluster segments, covering simple gauge cluster up to large TFTs. It integrates many features to build exciting HMIs at affordable cost.
-
product
PXI/PXIe Battery Simulator Module, 4-Channel, V/I Readback, 750 V Isolation
43-752A-012
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
product
Battery Leak Testers
Battery leak testers are crucial tools in the quality assurance process for battery manufacturing. These testers are designed to detect any leaks in battery cells, ensuring that the batteries are safe and reliable for use. Battery leaks can lead to reduced efficiency, potential damage to devices, or safety hazards. By employing sophisticated techniques, such as pressure decay methods or helium detection, battery leak testers can identify even the smallest imperfections in battery casings. These testers are essential in industries where battery reliability is critical, such as in automotive, consumer electronics, and renewable energy sectors, ensuring that the batteries meet stringent safety and quality standards.
-
product
High Speed Camera Systems
MEMRECAM MX
The nac MEMRECAM MX is a robust, turnkey solution for multi-camera onboard and offboard automotive testing and occupant safety applications. Each system supports up to eight, tightly synchronized camera views, and integrates seamlessly with all current and legacy MEMRECAM imaging systems.
-
product
Dual Bus 75-Channel 2A PCI Fault Insertion Switch
50-190-002
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
product
Programmable DC Electronic Load
DL3000 Series
The DL3000 series is a cost-effective, economical programmable DC electronic load with a friendly human-machine interface and excellent performance specifications. It provides a variety of remote communication interfaces to meet diverse testing needs for design and testing. A wide range of solutions are available for a wide range of industries including automotive electronics, aerospace and fuel cells.
-
product
DC-DC Converters
Our proven ability to blend circuit topologies and high-performance components with contemporary construction techniques has led to our premier position in the industry as the largest supplier of DC-DC converters. From standard models to modified products and complete custom designs, Murata''s DC/DC converters can meet the needs for miniaturization, low profile, high efficiency, power-saving, low noise designs for use in industrial and electronic equipment, telecom, medical, automotive, lighting, and more.
-
product
Automotive Noise Finder
7632
Peaceful Thriving Enterprise Co Ltd
This is a portable automotive noise finder which can quickly detect source or location of noises emanated from bearing, gear, valve, valve body, crankshaft, cylinder, gearbox, car body and more parts after staring engine. It helps the serviceman to find out the actual noise part even in severe ambient noise.
-
product
Automotive Sensors
Vehicle electrification (e-mobility), sustainability (zero emissions), increased safety & productivity are trends significantly impacting the role of sensors in passenger and commercial vehicles. This includes the requirement to enable greater e-motor performance and efficiency, reduced charging time, increased battery life, cleaner and more efficient internal combustion engines, reduced maintenance / vehicle down-time as well as highly robust ADAS and autonomous driving safety systems. TE offers a diverse sensor technology portfolio, combined with deep application expertise gained from extensive experience of delivering quantifiable value across a wide range of demanding passenger & commercial vehicle applications.
-
product
PXI/PXIe Battery Simulator Module, 2-Channel, V/I Readback, Simplified Current Sink, 750 V Isolation
43-752A-913
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
product
PXI/PXIe Battery Simulator Module, 4-Channel, V/I Readback, 1 kV Isolation
41-752A-112
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
product
Electrical
This category covers test equipment required for electrical performance tests on Industrial Lighting, Street Lighting, Automotive Lighting, Appliances, Accessories & related products. A wide range of Electrical Test Panels, Electro-mechanical endurance test systems for many products, Appliance test systems and also a range of low energy spot welding machines (one of the very few products we make which are not test equipment). Equipment are custom built to suit specific customer requirements.
