Filter Results By:
Products
Applications
Manufacturers
Noise Sources
create signal disturbances for the purpose of noise instrument calibration.
See Also: Pink Noise, Noise Generators
-
product
Noise Sources
This power amplifier ensures that you get the maximum sound pressure level out of the Norsonic range of speakers.
-
-
product
Noise Sources
WGNS
The system allows the user to extend the frequency range of the NFA to allow for accurate noise figure measurements to be performed on a device operating in the 26.5 – 170GHz range on wafer as well as in benchtop applications. Farran offers the WGNS series of noise sources to be used in conjunction with the FBC down converters for use as frequency extenders for noise figure measurement test system.
-
product
High-Power Noise Sources
These modules not only contain the noise diode circuitry, but also gain stages to boost the output power. While lower frequencies (under 2 GHz) are most common, Mercury produces powerful amplified noise modules up to 18 GHz. Noise modules are available in coaxial, surface mount and pin type construction. TTL control options are available.
-
product
Broadband Calibrated Noise Sources
Fairview Microwave’s calibrated noise sources cover frequency bands from 10 KHz to 18 GHz. Their performance specifications include output ENR levels ranging from 15 dB to 30 dB and typical VSWR levels as low as 1.25:1. Depending on the model, calibrated frequency points are at 10 MHz, 100 MHz, 1000 MHz, 2000 MHz and 1 GHz steps. The temperature coefficient of these noise sources is < 0.01 dB/°C and noise output variation is < 0.1 dB/%V.
-
product
High Power Noise Sources
NS-7001
The NS-7001 is high-power noise source specifically designed to operate in the 2.11-2.17 GHz UMTS band. It features flat output power that is regulated over a wide temperature range with high rejection outside the operating band of interest. Logic control is provided to enable/disable the noise source and an internal BIT function continuously monitors the output power. Other frequency bands and power levels are available.
-
product
Noise Sources
The Keysight 346, 347 and SNS Series of noise sources work in conjunction with the NFA Series noise-figure analyzers to make noise-figure measurements from 10 MHz to 50 GHz.
-
-
product
Noise Sources
NC3208
It offers a high ENR output AWGN noise over a wide frequency range. This Noisecom noise source has excellent stability with temperature and voltage for tough environments. It contains a hermetically packaged noise diode that has been pre-selected for special performance characteristics. This module is ideal for many different applications including radar warning receivers (RWR), built-in test equipment (BITE), military aircraft, and Wi-Fi.
-
product
10 MHz to 55 GHz Noise Sources
CNS346 Series
The Spanawave CNS346 Series is designed for precision noise figure measurement applications. The superior VSWR characteristics reduce multiple reflections of the test signals and significantly increase the measurement accuracy of most noise figure set-ups. The CNS346 Series noise sources have broadband coverage and extremely good temperature and voltage stability, for the finest noise figure meter-compatible laboratory standards. Outputs of 6, 15.5 and 22 dB ENR are available, allowing the units to accurately measure noise figures up to 20 ,30 and 36 dB respectively.
-
product
Noise Sources
NC1126A
This noise source by Noisecom produces white Gaussian noise up to +13 dBm. It contains a hermetically packaged noise diode that has been pre-selected for special performance characteristics. This module is ideal for many different applications including CATV, Secure communications, Jamming systems, OC-192 Testing, EW & EC.
-
product
Noise Sources
NC1128A
This noise source by Noisecom produces white Gaussian noise up to +13 dBm. It contains a hermetically packaged noise diode that has been pre-selected for special performance characteristics. This module is ideal for many different applications including CATV, Secure communications, Jamming systems, OC-192 Testing, EW & EC.
-
-
product
Precision Calibrated Noise Sources
ELVA-1's calibrated noise source ISSN-XX series delivers a uniform level of noise power spectral density within the whole waveguide frequency range. Sources are available in eight waveguide bands covering 26.4-170 GHz.
-
-
product
Noise Figure Analyzers & Noise Sources
Keysight Technologies provide a range of noise figure measurements solutions to meet your needs, from the NFA series noise figure analyzers to the noise figure measurement personalities for our spectrum analyzers. We also have a range of noise sources to complete the measurement solution.
-
product
Noise Location Package
Type HFDF
National RF’s Type HFDF high frequency location system is a proven noise hunting and location directional antenna system that allows you, in many cases, to walk right up to the source of High Frequency (HF) noise! Used by several power companies around the United States, professional noise hunters, and other communications specialists, the HFDF has located noise sources that emanated from pole power transformers, arcing electric fences, CATV in-line amplifiers, plasma TV screens, and even Marijuana grower’s heating lamps! The system incorporates several plug-in, tunable magnetic loop sensors of a proprietary National RF design, that cover the frequency range between 1.8 MHz and 55 MHz. The unit is packaged in a hand-held, lightweight metallic enclosure, with a pistol grip and a magnetic compass mounted on top. The compass is used to get magnetic bearings to the noise source, which may be plotted on a map to triangulate, and ultimately pin-point, the location of the noise source. In certain cases, our customers tell us that they have been able to walk right up to the interfering noise source and correct the situation on the spot!
-
product
High-Current, Ultra-Low Noise Filter, 21 V / 500 MA, 10 Ω
N1298A
The N1298A Series is a collection of low noise filters for the Keysight B2960 Series 6.5-digit low noise source.
-
-
product
Noise Figure Analysis Using NI PXI RF Test Instruments
NI-RFmx Noise Figure
Measure noise figure, gain, Y-factor, effective temperatures, hot and cold power, and moreOptimized calibration and measurement routines for multi-DUT test using Y-factor and cold sourceSupports the PXIe-5668R 26.5 GHz VSA, the PXIe-5698 26.5 GHz preamplifier, and VSTsDesigned for use with industry-standard noise sources such as the Noisecom NC346 Series
-
product
Noise Figure Analyzer, Multi-touch, 10 MHz to 40 GHz
N8976B
The N8976B high performance noise figure analyzer is designed to make fast, accurate and repeatable noise figure measurements. When paired with an SNS Series noise source and U7227 Series USB preamplifier the ENR data from the SNS and USB preamplifier data automatically downloads into the N8976B.
-
product
SNS Series Noise Source 10 MHz to 18 GHz (ENR 6 dB)
N4000A
The SNS series N4000A noise source is designed for accurately measuring devices with low noise figure, with a frequency range of 10 MHz to 18 GHz and nominal ENR 6 dB.
-
product
Noise Source
MNS-1
Matrix Test Equipment Incorporated
The MNS-1 is a shaped noise source that can be used toemulate 2 bands of digital carriers. While it does not havethe necessary attributes to generate a constellation, it doesmimic the loading of QAM carriers. The MNS-2 featuresremotely controllable 6 MHz wide notch filters to allowintroducing a QAM carrier capable of generating a constellationand enabling measurement of Modulation Error Ratio (MER) andBit Error Rate (BER).
-
product
Acoustics
When it comes to selecting a microphone for product tests—whether for sound power, sound quality, or noise source location—there's no need to compromise to sacrifice quality or performance for affordability.
-
product
Speaker Component Checker
Cab Driver
Whirlwind Music Distributors, Inc.
The CAB DRIVER is a test device for checking the operation of the speaker components within enclosures. A pink noise signal source is sent through pushbutton selectors to an assortment of speaker connectors, including Speakon NL8 and NL4, 1/4" TS and banana jacks. Speaker/ Polarity/ Impedance/ Pink Noise Generator
-
product
Electronically Tunable Filters
ETF
Radar. Communications. EW/SIGINT. Frequency agile channelization. Frequency agile noise rejection filter. Local oscillator tracking filter. Controlled bandwidth and center frequency noise source.
-
product
Surface-Mount Noise Sources
Mercury’s family of surface-mount noise sources provides exceptional performance in a compact and easy to integrate package. These products are ideal for applications such built-in test and dithering circuits where the system requirements drive a need for compact, surface mount technology.
-
product
Ultra-Low Noise Filter, 42 V / 105 MA, 50 Ω
N1298B
The N1298 Series is a collection of low noise filters for the Keysight B2960 Series 6.5-digit low noise source.
-
product
USB Smart Noise Source, 500 MHz To 50 GHz, 5 DB ENR Nominal
U1832C
The USB-powered (USB TMC compliant) U1832C provides broadband noise figure measurements from 500 MHz – 50 GHz with modular signal analyzer, benchtop X-Series signal analyzers and Fieldfox
-
product
Power Sensor and SNS Noise Source Cable (1.5m / 5 feet)
11730A
The Keysight 11730 series power sensor cables are used with the 8480 and E-series power sensors (except the E9320 family of peak and average sensors). These cables are designed to reduce RFI effects on low power readings with an improved shielding design in the cable itself. Cables may be ordered individually or in pairs in any combination desired for single and dual-channel measurements.
