Pressure
Force exerted over it's given surface area.
See Also: Differential Pressure, Absolute Pressure
-
Product
Cylinder Leakage Testers
EEPV509
-
Input pressure gauge displays input air pressure for proper cylinder leakage test set up and accurate results Pressure gauge range is 0-100 psi (0-700 kPa) in 2 psi (20 kPa) increments Cylinder leakage gauge displays leakage as a percentage of input pressure with 3 distinctive zones of high, moderate and low
-
Product
Vapor Source Mass Flow Controller With Viscous Choked Flow
-
The 1150C Vapor Source Mass Flow Controllers are pressure based measurement and control systems designed to meter and control vapor from low vapor pressure liquid and solid sources directly, without the need of a carrier gas using viscous flow through a choked orifice.
-
Product
Low Pressure Variable Reluctance Sensor
DP45
-
The Validyne DP45 Very Low Differential Pressure Transducer is designed for extremely low pressure measurement in the order of 1 inch water column. This instrument is used extensively in connection with flow measurements where dynamic response at low flow rates is required. Dynamic line pressure effects are minimized due to the combination of low internal volume, symmetrical construction, and small volumetric displacement inherent in the DP45 design.
-
Product
True Airspeeds
-
These true speed indicators are differential pressure indicators that measure the difference between static and total pressure produced by ram air from the pitot. The indicated airspeed can be corrected for changes in altitude by turning the knob to align the outside air temperature with the altitude. The moveable airspeed scale will then show the actual, or true, airspeed.
-
Product
Data Acquisition Systems
-
Encore Electronics manufactures a wide range of analog signal conditioning equipment, including strain gage and pressure amplifiers, frequency-to-voltage converters, thermocouple isolation amplifiers and anti-aliasing filters.
-
Product
Mid-Range Gas Filter Correlation CO2 Analyzer
Model N360M
-
Teledyne Advanced Pollution Instrumentation
The Model N360M measures carbon dioxide (CO2) by comparing infrared energy absorbed by a sample to that absorbed by a reference according to the Beer-Lambert law.The N360M uses Gas Filter Correlation (GFC) to overcome the interfering effects of various other gases (such as water vapor) that also absorb IR. The analyzer passes the IR beam through a spinning wheel made up of two separate chambers: one containing a high concentration of CO2 known as the reference, and the other containing a neutral gas known as the measure. The concentration of CO2 in the sample chamber is computed by taking the ratio of the instantaneous measure and reference values and then compensating the ratio for sample temperature and pressure. A nitrogen purge system is provided for the GFC wheel assembly to eliminate the effects of ambient CO2, if necessary.
-
Product
Wireless Data Logger System
HD35
-
Wireless datalogging system allowing the monitoring of a multiplicity of physical quantities in the most diverse fields of application. Temperature - Humidity - Atmospheric and differential pressure - Illuminance - Irradiance UVA, UVB, UVC, CO, CO2 - Solar radiation - Precipitation - Wind speed and direction, Leaf wetness, Volumetric soil water content, Level, WBGT.
-
Product
Multifunction Calibrators
-
Many of the calibrators we offer are multifunctional calibrators, that is because then you don’t need to carry so many devices and also don’t need to recalibrate several devices. For us the “multifunctional” means a calibrator that can measure and generate electrical, temperature and pressure signals.
-
Product
Mid-Range Gas Filter Correlation CO Analyzer
Model N300M
-
Teledyne Advanced Pollution Instrumentation
The Model N300M is a microprocessor-controlled analyzer used to determine the concentration of carbon monoxide (CO) in a sample gas. The analysis method is based on the Beer-Lambert law.The N300M uses Gas Filter Correlation (GFC) to overcome the interfering effects of various other gases (such as water vapor) that also absorb IR. The analyzer passes the IR beam through a spinning wheel made up of two separate chambers: one containing a high concentration of CO known as the reference, and the other containing a neutral gas known as the measure. The concentration of CO in the sample chamber is computed by taking the ratio of the instantaneous measure and reference values and then compensating the ratio for sample temperature and pressure.
-
Product
Precision Barometer
HD3114B
-
Temperature, humidity and pressure handheld data logger with color graphic LCD display.
-
Product
Environmental Chamber
REXMED REC-200
-
MOD. REC-200, AC 230/380/415V, 1/3 phase, Environmental chamber, HS CODE: 841989, UNCCS CODE: 484384, UMDNS CODE: 16327, Main construction: SS304, Interior: SS304, Exterior: SS304 powder coated, Insulation: Rigid polyurethane foam and glass wool, Controller: Fix point PID controller, temperature ˚C/PV and ˚C/SV, humidity %/PV and %/SV display and setting, Temperature range: -20˚C~100˚C, Humidity range: 20%RH~98%RH, Constancy: ±0.3˚C ±2.5%RH, Uniformity: ±1˚C ±3%RH, Temperature and humidity sensor: PT 100Ω, Temperature and humidity audio and visual warning and OFFS correction setting, Temperature heater: 1.5KW X 2pcs, Humidity heater: 2.5KW X 1pc, Heat up transition time: -20˚C~100˚C within 35 min, Refrigeration system: Air cooled, single stage, Cooling compressor: Bristol hermetic compressor, Cooling capacity: 1,892 Watts, 6,455 BTU/hr, 1,630 Kcal/hr, Cool down transition time: 20˚C~-20˚C within 45 min, Safety devices: No fuse breaker, refrigerator over load relay, refrigeration high pressure switch, over temperature protector, protection relay, protection fuse, water level control and overheat protector, Chamber: L50 X W60 X H75cm, Capacity: 225L, chamber with key lock, with lamp (DC 12V 50W) X 1pcs and double glass viewing window, testing cable port with cover: Ø25mm, 4 castors, W/S: shelf X 2pcs, standard testing wet cloth X 5pcs, PCV water container X 1pc
-
Product
High-Speed Real-time Recording Systems
Talon
-
Talon® High-Speed Recording Systemseliminate the time and risk associated withnew technology system development. Withincreasing pressure in both the defense andcommercial arenas to get to the market first,today’s system engineers are looking for morecomplete off-the-shelf system offerings.
-
Product
Pressure-Force Cables And Connectors
-
Connectors used for pressure and force sensors. Includes cable assemblies for pressure transducers and load cells, DIN connectors, twist lock connectors, push on connectors, and dynamic sensor cables.
-
Product
Tyre Pressure and Infra-Red Sensors
-
The system consists of a powered pressure and temperature sensor with transmitter fitted to a wheel rim. This sends pressure and temperature data over an RF link to a compact receiver on the car. Sampling rates increase automatically when either a change in pressure is detected or when wheel inertia is detected. The system stops transmitting below a threshold pressure to preserve battery life. The receiver sends data to the car control via CAN.
-
Product
Test Adapter / Vacuum Adapter
-
GPS testing technology offers a large selection of vacuum adapters. The support with vacuum (negative pressure) results in increased ease of use and larger pressures can be built up easily and thus more test needles can be contacted.We recommend the use of vacuum hoods or, if contact is required on both sides, our vacuum swivel hood.
-
Product
Residential/Commercial Combustion Analyzer w/ NOx Sensor
C165+N
-
UEi Test & Measurement Instruments
Backed by UEi Service+ to give up to 6 years’ warranty, next day recertification, and a reduced cost of ownership. The C165+ Residential/Commercial Combustion Analyzer is easy to use with a rugged design, multiple sensor protections, altitude compensation and differential pressure. Prints to optional printer and wireless App. The new LINK feature connects the included wireless pipe clamp temperature probes and other optional probes to the C165+. Essential information for installing and maintaining furnaces and boilers all in one device.
-
Product
HL Deadweight Tester
-
AMETEK Sensors, Test & Calibration
The HydraLite Tester is a primary standard available as a dead weight tester or a gauge. Both feature a re-entrant type measuring piston and cylinder assembly. This design reduces the rate of fluid leakage and increases float time, helping to maintain accuracy as test pressures increase.
-
Product
Square Root - Gauge Line Error Indicators
-
Parker PGI's SRE6 and GLE6 Indicators are designed to quantify Square Root and Gauge Line Errors in natural gas orifice flow measurement. They identify inaccuracies caused by compressor-induced pulsation and differential pressure discrepancies.
-
Product
Ballistic Test Equipment
-
n 1998, H-S Precision introduced ballistic range equipment and fixtures designed to compliment its line of ballistic test barrels. Equipment is available for pressure and velocity testing, NIJ body armor testing, ballistic armor testing and extreme accuracy testing. We are the leading supplier and producer in the World for the ballistic test barrels. The most well known ammunition companies use H-S barrels for testing the quality and consistency of their ammunition.
-
Product
Differential Pressure Meters, Micromanometers
-
Unprecedented differential pressure measurement accuracy (yet a wide range) for critical pollutant pathway monitoring, ventilation assessment, filter performance testing, general HVAC measurement and many other applications. GrayWolf AdvancedSense meters include auto-ranging dual DP sensors, as well as auto-zeroing (to maintain low-end precision). GrayWolf DP instruments offer broad measurement ranges, yet exceptional sensitivity. They may be utilized for spot checks and for long-term trending of a variety of pressure measurement applications that require high reliability. Choose from the cutting edge AdvancedSense Pro, AdvancedSense BE or the new Zephyr III Meter (which replaces the workhorse “classical” Zephyr II in July 2020).
-
Product
Vacuum Meters
-
Portable meters for absolute vacuum pressure measurements in hospital labs, crystal growing, solvent recovery, distillation, and rotary evaporation.
-
Product
Abrasive & Blast Inspection
-
Blasting parameters: A number of important parameters need to be monitored during the blasting or water jetting process, these include: air pressure (at the nozzle), nozzle diameter, blast media contamination & pH values in order to avoid recontamination of the substrate during blasting.
-
Product
Steam Aging Test Chambers
-
Dongguan Amade Instruments Technology Co., Ltd
Steam aging test chamber is a climatic test machine used to judge the products performance to resist extreme circumstance under high temperature, high humidity and high pressure during the transportation, storage and usage. The principle is very simple, water in the tank is heated turning into steam to form a simulated test environment under specified temperature and humidity. Specimens are placed into the drawers of machine to carry out test lasting for preselected time. It is applicable to electronic connectors, semiconductor IC, transistor, LCD, diodes, resistances etc.
-
Product
Three-Parameter Water Quality Analyzer (three-parameter water level gauge)
HR8833
-
HighReach Measuring & Controlling System Co.,Ltd
The HR8833 integrated pressure water level gauge is a three-parameter (water level, water temperature, conductivity) measurement product. It can be used with digital atmospheric pressure meter. It can be externally powered and self-powered by internal battery. It can be The product includes a water level sensor, a temperature sensor and a conductivity sensor, a built-in large-capacity non-volatile memory and a high-capacity long-life lithium battery, For three-parameter hydrological parameter measurement of surface water, groundwater and marine environment.
-
Product
RK Deadweight Tester
-
AMETEK Sensors, Test & Calibration
The RK floating ball type pneumatic dead weight tester is engineered to offer user-friendly, safe operation. The easy-to-use primary standard provides reliable and accurate pressure measurement in the field, or in a lab.
-
Product
Pressure Insensitive Mass Flow Controller
SEC-Z700X Series
-
The SEC-Z700X Series is equipped with reliable thermal sensors and a pressure insensitive function for stable flow rate control. The on-board pressure measurement reduces the cost, size and complexity of gas delivery systems.
-
Product
Heat Seal Tester
HST-01
-
Jinan Leading Instruments Co., Ltd.
HST-01Heat Seal Tester seals the specimen to determine the seal parameters of basicfilm, laminated films, coating paper and other heat sealing laminated filmsaccording to the requirement of relative standards. The seal parameters includeheat seal temperature, dwell time, and the pressure of heat seal. Heat sealmaterials that have different melting point, heat stability, fluidness, andthickness of could show various heat seal properties, which cause obviouslydifferent seal technique.
-
Product
Data Loggers
-
PTC® Instruments is a west coast distributor for MadgeTech® data loggers. Record carbon dioxide, humidity, temperature and pressure. The temperatures for perishable goods in transit, HACCP Compliance, HVAC, medical, pharmaceutical, sterilization, environmental research, perishable goods, food storage monitoring, warehouse monitoring, environmental studies, wine cellars, humidors, refrigeration, archival storage for fine art and books.
-
Product
FEA and Strain Gauge Testing
-
Circuit Check began Strain Gauge Testing in 1999 when BGA/SMT technology started replacing PTH components, reducing strain levels was a reactive post fixture fabrication process. We quickly recognized that the “reactionary” process was neither efficient nor were we capable on knowing the lowest achievable strain levels. Our engineering team came up with visual tools utilized during design to easily identify areas of excessive probe force, though still not enough data was generated to identify the lowest possible strain. Finite Element Analysis software models the PCBA and test fixture and applies the pressures from test probes and board supports and indicates the micro strain level applied to the PCBA. Using the FEA software during our design process allows our engineers to modify fixture designs to attain the lowest possible micro strain before fabrication begins.
-
Product
Water Level Temperature Monitoring Recorder
HR8801
-
HighReach Measuring & Controlling System Co.,Ltd
HR8801 water level temperature monitoring recorder is a groundwater level temperature monitoring instrument with external power supply and internal battery self-power supply. It can be used for long-term recording of water depth (pressure) and temperature. Included water level and temperature sensor, built-in large capacity. Non-volatile memory and high-capacity long-life lithium battery for long-term monitoring of water level in surface water, groundwater and marine environment.
