Product

Fiber Identifier

OFI-20A

-

ShinewayTech

OFI-20A - ShinewayTech

OFI-20A can detect optical signal presence, type and direction anywhere on fibers during optical network deployment, maintenance and troubleshooting. With non-destructive macro-bend detection technology, it introduces no damage to tested fiber or interference to the service on fiber. OFI-20A is able to identify wide-spectrum signals (such as signals in CATV system) and can be used in SONET/SDH & DWDM systems tests.

Product

MEMS Fiber Optical Switch at Single Mode 1315nm Type-A with LC/PC Connector

SUN-MS-1x8

-

Guilin GLsun Science and Tech Group Co., LTD

SUN-MS-1x8 - Guilin GLsun Science and Tech Group Co., LTD

Fiber Configurations 1x8 MEMS Fiber Type SM, 9/125 umTest Wavelength 1310/1550 nm Operating Voltage 2.5VSwitch Type Non-latching Fiber Length 0.5m±5cmConnector TTL/UART Tube Type 900 umOperating Temperature -5°C~ +70°C Storge Temperature -40°C ~ +85°C

Product

Fiber Identifiers

-

Fiber Instruments Sales Inc.

Fiber Instruments Sales Inc.

This equipment is rugged and easy-to-use making it simple for a technician to identify live fiber which ensures that the fibers are connected. This tool also identifies the frequency and the traffic direction. It saves time and money when compared to other pieces of more elaborate test equipment. Most importantly, this device performs this task without any harm to the fiber optic cable. Because the technician is only clamping the device on the fiber the identifier does not disrupt signal traffic.

Product

RGB Digital Fiber Optic Amplifier

CZ Series

-

Keyence

CZ Series - Keyence

RGB Digital Fiber Optic Type. RGB three-light source. Wide detection range of up to 7020 mm. High-speed response of 300 s. Water-resistant sensor head IP-67 rated

Product

Ultrafast Fiber Optic Photodetectors

DXM Series

-

Thorlabs, Inc.

DXM Series - Thorlabs, Inc.

The DXM series of Ultrafast Detectors are fiber-coupled photodetectors with wide wavelength ranges, as shown in the plot to the right, that are designed to be used for a variety applications. Each provides a high-fidelity electrical output pulse in response to an optical input pulse, and their clean impulse responses have full width half maxima (FWHM) down to 15 ps.

Product

Quartz Sensor Fiber Head

SLG-1001

-

SAN-EI ELECTRIC CO.,LTD.

SLG-1001 - SAN-EI ELECTRIC CO.,LTD.

Pure quartz fiber stands aving high UV transmission properties are used. This is the quartz sensor fiber head exclusive for the UV MONITOR SERIES excelling in flexibility and durability. The exclusive use receptacle for the light receiving inlet is also available.

Product

Digital Fiber Multiplexers & Wavelength Shifters

FiberSaver Series

-

Multidyne

FiberSaver Series - Multidyne

We don’t always have unlimited amounts of fiber at our disposal. Whether working in pre-fibered event venues, houses of worship or moving camera signals across busy metropolitan areas, fiber counts can quickly add up – especially when bi-directional optical transmission is required. MultiDyne’s FiberSaver Series is built for the system designer who needs a robust yet compact solution for signal links where fiber strands are limited, or where fiber feed requirements exceed budgets. FiberSaver products help technicians send and receive more optical signals over fewer fibers. Wavelength-agnostic inputs will multiplex just about any digital optical coming from SMPTE cameras, Network Switches, etc., and combine them with several optical matrix inputs. Scalable in increments of six channels, content producers now have a cost-effective solution to carry extra signals for sports production, distance learning and remote broadcasting.

Product

Miniature Fiber Optic Pressure Transducers

-

FISO Technologies Inc.

FISO Technologies Inc.

*The diameter of the working length section can be as small as 0.5 French *The sensor tip size can be as small as 0.8 French The flexibility of the glass fiber offers excellent deliverability without being prone to kinking like electrical wires *The front looking configuration of the sensor tip prevent side-facing/wall bouncing artifacts in the measurement*The lack of metallic components provide full immunity to interference from RF, MW and MRI systems

Product

Fiber Optics

-

Avantes Inc.

Avantes Inc.

The use of fiber optics as light guidance allows great modularity and flexibility in the setup of an optical measurement system. Optical fibers can be made of many materials, such as plastic, glass, and silicates (SiO2). For high-quality fibre optics, as used in spectroscopic applications, synthetic fused silica (amorphous silicon dioxide) is used, which can be intentionally doped with trace elements to adjust the optical properties of the glass.

Product

Mini Fiber Tester (ST Type)

21-8681-00

-

LANTAC Techtronics Co. LTD

21-8681-00 - LANTAC Techtronics Co. LTD

The portable design is easy to carry and operation. 2. Low-cost multi-function is more economical. 3. The multiple LEDs display a clear indication. 4. Power saving automatically and Battery low indication.

Product

Pulsed Fiber Amplifier

MOPA

-

Fibotec Fiberoptics GmbH

MOPA - Fibotec Fiberoptics GmbH

These light sources are compact Master Oscillator - Power Amplifier (MOPA) structures that can be directly modulated in a defined operating range of repetition frequency and pulse power. The standard products operate in the wavelength range around 1.5 µm at a repetition frequency > 6 kHz and a pulse energy of 10 µJ/50 ns (200 W peak power).

Product

AGC Fiber Amplifier

-

Analog Systems

Analog Systems

Range of fiber amplifiers with power supplies.

Product

Fiber End-face Interferometer

-

Anfkom International Co.,Limited

Anfkom International Co.,Limited

1.Automatic MeasurementSANA2 is equipped with the locking handle sensing unit to monitor the device locking status. To further simplify the testing process, the instrument can start the measurement once the device to be tested is fully locked. Operator can also click the button aside the locking handle to trigger the measurement.2.0~12° APC Angle Auto TuningBenefit with the unique fixture design, SANA2 can tune the APC angle precisely from 0°to 12°automatically, meeting any special requirement on APC angle setting.3.Simple and User Friendly Interfaces and Excellent 3D ImagesThe software of A 2 is simple and user friendly, you can change the language within the software. It provide many endface rebuild method such as 3D, 2D, plot to assist the engineers about the process. The test reports and data are generated automatically for analyzing and tracing.4.Auto Centering ImagesSANA2 has auto centering image function that can find the fiber and makes it to center automatically within one click.No mouse drag or hardware adjustment is needed.5.Cleave Angle Measurement

Product

Fiber Optic/BNC Converters

-

VI Control Systems Ltd.

VI Control Systems Ltd.

The active receiver and transmitter require power while the passive transmitter requires a TTL signal that is capable of driving 75 mA.

Product

Fiber Switches

-

piezosystems jena, Inc.

piezosystems jena, Inc.

Piezo-electric driven switches are especially designed for fast switching – measured in milliseconds. Piezo actuators enable the optical switch to couple optical fibers with an accuracy of a few microns. The piezo driven optical switches are available fiber core diameters of 50 µm up to 600 µm.

Product

Entry-level Price Interferometer for Geometry Measurement of Single Fibers

3D SCOPE-V2

-

DATA-PIXEL SAS

3D SCOPE-V2 - DATA-PIXEL SAS

Specifically designed for use in a production environment, 3D Scope-V2 is a robust, compact and easy to use interferometer that brings speed and precision to operators. 3D Scope-V2 supports our Blink software platform. Non-compressed, real time and high quality images are transfered from the hardware to the software via a USB 2.0 link in addition to the automation and control commands.

Product

Fiber Optic Sensor Head Variations

FU Series

-

Keyence

FU Series - Keyence

11 Fiber Optic Sensor Head Variations. Flexible Stainless Steel Jacket. Wide Area Detection. Hex-shaped Heads for Trouble-free Mounting. Heat resistant. Small Beam Spot. Thin-sleeve Thrubeams

Product

Fiber Fusion Splicer

AV6471

-

Hangzhou Softel Optic Co., Ltd.

AV6471 - Hangzhou Softel Optic Co., Ltd.

The fiber fusion splicer(AV6471A )is FTTH fiber splicing machines is a new design of the optical fiber in equipment. In the light of the special FTTH environment.

Product

Spectroscopy Fiber Probes

-

art photonics GmbH

art photonics GmbH

Spectroscopy probes for medical diagnostics and industrial process control, in volume production of fiber for medical and industrial lasers, for different fiber bundles, etc.