Thermocouple Simulators
-
Product
Balance Thermocouple Power Sensor, DC To 18 GHz
N8481S
Power Sensor
The Keysight N8480S Series Balance Thermocouple Power Sensors are intended to be used as measurement standards for RF power. They are suitable for use in a microcalorimeter-based primary measurement standard and as a secondary or reference measurement standard. The new balance thermocouple power sensors offer a broad frequency range DC up to 18/50 GHz, high maximum input power of +20dBm, fast measurement speed/settling time as well as ease of maintenance.
-
Product
K Thermocouple Surface Probe
TP777
-
Surface thermocouple Type "K" probe. °C max: 200. Response time: 3 s.
-
Product
Simulator / Analyzer / Tester PCI BUS Interface Card
CIC301 - MIL-STD-1553
-
The CIC301 is a full-featured, high performance, Dual Redundant MIL-STD-1553 A/B serial bus Simulator Analyzer Tester designed as a plug in card for PCI backplane. The CIC301 includes full error injection and can operate in independent or simultaneous mode as a Bus Controller, multiple simulated Remote Terminals and full/selective Monitor. Its data structure can be changed on the fly without interrupting the processor for real time operation. The active monitor stores, time tag and annotates bus traffic with the message type and any detected errors. Stored words are annotated with a break down of the word error.
-
Product
Solar Cell Simulation
Setfos
-
Easily calculate the short circuit current, open circuit voltage Voc and fill factor with Setfos. Tweak the layer stack and add light scattering layers for enhanced absorption. Optimize for AM1.5 or specific wavelength bandsElectrical IV curvesCurve fitting & parameter extractionAC simulation and transient experiments like photo-CELIVAdvanced device physics: SRH-recombination, excitons, ... Design anti-reflection coatings or transparent cells
-
Product
Simulation Table
KRD61 6-DOF
-
KRD61 series 6-DOF simulation table is a closed-loop servo simulation platform consisting of six servo actuators and six sets of dedicated hinges connected at the top and bottom platforms respectively. By virtue of the telescopic movement of the six actuators, the upper platform moves in six degrees of freedom (X, Y, Z, α, β, γ), so various space motion attitudes can be simulated.
-
Product
Altitude & Space Simulation Test Chambers
-
Weiss Technik’s vast experience with altitude, thermal vacuum, low temperature and space simulation test chambers can provide you with the right solution. We offer both pre-engineered and custom altitude chambers for ultra-low cooling, extended mbar, and extended temperature ranges that will meet your testing exact requirement.
-
Product
Solar Array Simulator DC Module, 65V, 8.5A, 510W
E4361A
Simulator
The Keysight E4361A is a 510W solar array simulator DC power module that simulates the output characteristics of a solar array. The E4361A is primarily a current source with very low output capacitance. It offers fast I-V curve changes allowing you to accurately simulate the output of different solar arrays under various environmental conditions (ex. temperature, age, eclipse, spin etc.). The E4360 gives you the flexibility to operate it in two ways:
-
Product
Analog Simulator
MPLAB® Mindi™
-
MPLAB® Mindi™ Analog Simulator reduces circuit design time and design risk by simulating analog circuits prior to hardware prototyping. The simulation tool uses a SIMetrix/SIMPLIS simulation environment, with options to use SPICE or piecewise linear modeling, that can cover a very wide set of possible simulation needs.
-
Product
Panel-mounted Power Amplifier(Hardware In The Loop Simulation)
PA30Bi
-
PA30Bi is the panel-mounted type real time simulation amplifier with three-phase current and four-phase voltage.
-
Product
Wavefront Modeling And Simulation
-
The CAST-CRPA Simulation Systems provide a precise, coherent, and repeatable GNSS RF signal “wavefront”, that is a perfect solution for testing phased array, or “CRPA” antenna systems, in a laboratory environment. The system generates a complete set of RF signals for each antenna element, which are referenced to the phase center of the antenna manifold. In addition, the CAST system allows users to add interference and IMU signals that can also stimulate EGI’s and a wide range of modernized navigation devices.
-
Product
Thermocouple Calibration Furnace
9118A
-
The Fluke Calibration 9118A Thermocouple Calibration Furnace is a horizontal, open-ended tube furnace with a temperature range of 300 °C to 1200 °C. It is used for comparison calibration of noble and base-metal thermocouples by secondary high-temperature labs and instrument shops in industries such as aerospace, automotive, energy, metals, and plastics.
-
Product
Environmental Simulation
-
We provide a wide range of systems and devices for environmental simulation. Whether you are carrying out temperature, climate, vibration, corrosion, emissions, altitude, pressure or combined stress testing, we have the right solution and can supply systems in all sizes. From series products right through to customer-specific, process-integrated systems. The choice is yours! For excellent reproducibility and precise test results.
-
Product
Simulation
-
From structural analysis and computational fluid dynamics to injection molding simulation and advanced, cloud-enabled capabilities powered by Abaqus, SOLIDWORKS® and 3DEXPERIENCE® Works Simulation provide integrated analysis tools for every designer, engineer, and analyst.
-
Product
Fully Reflective Solar Simulators
-
Sciencetech manufactures four high power versions of class AAA fully reflective solar simulators. Sciencetech''s proprietary fully reflective design uses metal coated mirrors and passes the whole spectrum, no compromise. This is a distinct advantage over refractive based systems that are limited by the properties of the transparent material used.
-
Product
Fibre Channel Test & Simulation Interface for PCI
PCI-FC4
-
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
-
Product
K-Type Thermocouples Wire, Fiberglass (32deg F to 900deg F) 2 m
745690-K002
-
K-Type Thermocouple, 32°F to 900°F Temperature Sensor - The K-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure measurements and predefined scaling coefficients for the K-Type Thermocouple and acquire synchronized temperature data in units of degrees. The K-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.
-
Product
IBP Simulator
IBPS 2.0
-
The IBPS 2.0 is a PC controlled simulator to replace real IBP sensors. Originally designed for IEC 60601-2-34 testing, it can also be used by manufacturers to play their own test signals or database recordings.
-
Product
Modbus Simulator & Tester
Modbus Poll
-
Modbus Poll is a Modbus master simulator designed primarily to help developers of Modbus slave devices or others that want to test and simulate the Modbus protocol. With the multiple document interface you can monitor several Modbus slaves and/or data areas at the same time. For each window you simply specify the Modbus slave ID, function, address, size and poll rate.
-
Product
Thermocouple Power Sensors
N8481B
Power Sensor
N8480 Series Power Sensors are the replacement solutions for 8480 Series Power Sensors.
-
Product
Plastics Simulation Software
Moldex3D
-
Moldex3D is the world leading CAE product for the plastics injection molding industry. With the best-in-class analysis technology, Moldex3D can help you simulate the widest application range of injection molding processes to optimize product design and manufacturability, shorten time-to-market, and maximize product ROI.
-
Product
NIBP Simulator
SC-3 SimCube®
-
This NIBP only simulator provides features to perform basic NIBP testing of a patient monitor. Features one-button operation for quick testing of patient monitors and optional Battery Boost Option. Optional accessories provide all you need to test the NIBP parameter on any type of patient monitor.
-
Product
U1180A Thermocouple Adapter And Lead Kit, J And K Types
-
The Keysight U1180A thermocouple adapter and lead set are compatible with all series of Keysight Handheld Digital Multimeters. The set includes a J/K type Thermocouple adapter, thermocouple bead J-type and a thermocouple bead K-type.
-
Product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
GPS And GNSS Simulators
-
Safran’s GPSGlobal Positioning System is a navigation satellite system. See also / GNSSGlobal navigation satellite system (GNSS): A general term describing any satellite constellation that provides positioning, navigation, and timing (PNT) services on a global or regional basis. See also satellite simulators are easy to use, scenario-based instruments that combine a powerful, feature-rich platform with industry-leading value and affordability for any requirement for GPS testing.
-
Product
3D Electromagnetic Simulation Software
XFdtd®
-
A full-featured simulation solver, XFdtd outpaces other methods in efficiency as the number of unknowns increases. XF includes full-wave, static, bio-thermal, optimization, and circuit solvers to tackle a wide variety of applications, including antenna design and placement, biomedical and SAR, EMI/EMC, microwave devices, radar and scattering, automotive radar, and more. It also works with Remcom's ray-tracing products to provide thorough simulation capability at the low-, middle-, and high-end of the electromagnetic spectrum.
-
Product
Defined GNSS Simulator Software
BroadSim Revolutionary Software
-
BroadSim was developed to simplify the creation of advanced jamming and spoofing scenarios with Navigation Warfare (NAVWAR) testing in mind. With high-performing hardware, a robust and innovative software engine, and an intuitive user interface; BroadSim outperforms and exceeds features offered by the competition.
-
Product
Direct conversion from cycle driven simulation data
Test program generator
-
Direct conversion from cycle driven simulation data (ATPG scan patterns) (WGL/TDL/STIL) to tester. TDL/WGL/STIL to tester conversion Supports STIL ext 0,1,2 constructs Easy to use and cost effective conversion solution Optimize tester resources usage Supports advanced tester features (Such as Xmode, Multi-port etc’) Compress and minimize vectors count Allow direct tester binary patterns creation
-
Product
Pulse Oximeter Simulators
-
Take control of all your simulations with the next-generation SpO2 pulse oximeter simulator, OxSim Flex. The world’s smallest SpO2 tester now provides complete flexibility in selecting saturation, pulse rate and perfusion index. Users can create customized Preset Simulations for faster testing of oximeter performance and for alarm testing without having to change the monitor’s alarm settings!
-
Product
Boiler Thermocouple Monitoring System
BTM
-
The Boiler Thermocouple Monitoring System is used to acquire and archive data from thermocouples mounted on boiler tubes. Since this system interfaces directly with Allen Bradley Control Logix PLCs via EthernetIP communication, significant cost savings can be achieved by using it as remote IO.
