Thermocouple Simulators
-
Product
MAX31855 T-Type Thermocouple Sensor Breakout
SEN-30001-T
-
Breakout board for the MAX31855T digital thermocouple interface IC. Measured temperature range is -270C-400C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 1x5 pin header, has a vertical mini thermocouple connector and four mounting holes for standoffs and 4-40 screws.
-
Product
Load Cell Simulator
-
A High-Stability adjustable Load Cell Simulator. It is specifically designed for Load Cell Fault and System Fault Diagnosis. It also provides a useful Development Tool for any System which relies upon Load Cells. The Output Signal is adjustable from -0.1 to +3.1 mV/V.
-
Product
Production Caller ID Signal Simulator
AI-80
-
The AI-80 is a fully programmable stand alone Caller ID signal generator designed for production environments. It is capable of generating signals for all FSK and DTMF based Caller ID standards. Includes general telephone signal analysis features and a highly flexible programming language for sophisticated and complex production testing sequences.
-
Product
Thermocouple, Module, ITA, iCon Series, 96 Position
510161110
ITA Module
Primary mating module 510160110. (May mate with other Receiver modules, as well.)
-
Product
Resistor Simulation Card
SET-1210
-
The card has two ranges of values that meet the requirements of most functional test systems.The SET card is designed for applications in which resistive sensors provide information about parameters such as temperature (e.g. when testing motor controls)Each channel of the SET-1210 resistor simulation card is able to simulate the common short-circuit and no-load conditions, which can occur in a system due to faulty wiring or sensors.
-
Product
Transducer Simulator
Model 7
-
Impedance: 350 ohms nominal. Output Ranges: Fixed rotary switch. 0 to 3 mv/v in 6 steps of .5 mv/v .
-
Product
Transistor-Level Defect Simulator
Tessent DefectSim
-
Tessent DefectSim is a transistor-level defect simulator for analog, mixed-signal (AMS), and non-scan digital circuits. It measures defect coverage and defect tolerance. Tessent DefectSim is perfect for both high-volume and high-reliability ICs. Tessent DefectSim replaces manual test coverage assessment in AMS circuits needed to meet quality standards such as ISO 26262 and provides objective data to guide improvements in DFT. Tessent DefectSim dramatically reduces SPICE simulation time compared to simulating every potential defect.
-
Product
Load Simulator
Simulator
The load system is intended for testing satellite power supply systems; due to the integration with a solar array simulator and a battery simulator, it can perform validation and commissioning of satellite power supplies. The system is equipped with regenerative electronic loads and customer-specific high-power switching matrices for routing the DUT channels to the relevant loads. The individual voltages and currents for each channel can be read back via a Keysight Technologies switch mainframe.The system is equipped with high electrical power; its loads are capable of feeding the energy back into the power grid.
-
Product
PXI/PXIe LVDT/RVDT Simulator Module, 2-Banks
43-670-103-AABBCC
Simulator
The 41/43-670-103 is ideal for the simulation of variable differential transformers (VDT), both linear (LVDT) and rotary (RVDT) types. It has two banks, each capable of simulating the output of a single 5 or 6-wire VDT or resolver, or dual 4-wire utilizing a shared excitation signal.
-
Product
Accelerometer Simulator
MTN/8302
-
The MTN/8302 is a battery-powered unit designed to simulate a constant current type accelerometer. It enables test and calibration of vibration monitoring equipment such as the Monitran MTN/6000 series.
-
Product
Spring/Non-Spring-Loaded Thermocouple
8PT25
-
The AMETEK 8PT25 Spring/Non-Spring-Loaded Thermocouples for Frame 6, 7 and 9 applications have been designed, fully tested and qualified to meet OEM specifications. Power Instruments’ expertise in solving creep, stress rupture, corrosion, EMF drift and other problems affecting sensor performance has resulted in a robust line of single and dual element thermocouple designs. This thermocouple is immersed directly into the turbine fluid to monitor temperature while in operation.
-
Product
Solar simulation systems
-
Whatever your application, from an environmental chamber for small components to an extensive array for a complete automobile or aircraft test, EYE / Iwasaki has the experience to provide a solar lighting system customized for your requirements.
-
Product
Resistor Simulator Card
CP-RESSIM-16
-
The CP-RESSIM-16 Resistor Simulator PCIe Card provides programmable resistance simulation across multiple channels for real-time test and validation environments. The card supports 16 independent digital programmable resistors, enabling accurate emulation of variable resistance conditions within a system.
-
Product
PXI Strain Gauge Simulator Module 6-Channel, 2k
40-265-306
Strain Gauge Simulator
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 6-channel, 2kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
Product
High Intensity Pulsed Solar Simulator
GEN 2
-
Alpha-Omega Power Technologies, LLC.
The GEN 2 pulsed solar simulator and data acquisition systems can generate over 1,200 suns with a spot size of 12 mm x 12 mm at a rate of 2 pulses per second.
-
Product
Thermocouple Power Sensors
N8481H
Power Sensor
N8480 Series Power Sensors are the replacement solutions for 8480 Series Power Sensors.
-
Product
PCI Simulation Modules For Sensor Simulation
-
Does your test strategy require simulating environmental sensors, including temperature, pressure, altitude, and strain gauges.
-
Product
ESD - Simulator
SESD 230
-
The test generator SESD 216 simulates electrostatic discharge as defined in the standard IEC / EN 61000-4-2. Depend on the Equipment Under Test (EUT) and the test set-up for laboratory tests the IEC standard shows two test methods
-
Product
Solar simulators
-
Solar simulators enable the measurement of (dark and) light IV characteristics and of power and efficiency of photovoltaic An artificial light source is used to create illumination conditions that are similar to those in natural sunlight. International standards hosted by ASTM, IEC and JIS allow to classify the properties of a solar simulator with respect to spatial light uniformity, spectral content of the light and time variation of intensity.
-
Product
Battery Cell Simulation / Emulation
BMS
-
Efficiency, reliability and safety of modern lithium ion batteries for electric vehicle drives strongly depend on the battery management system (BMS) as their electronic control unit.
-
Product
Satellite Simulators
-
Tampa Microwave''s satellite simulators provide a compact easy to use training and evaluation tool for satellite earth terminals. We provide a variety of models with different combinations of frequency bands, transmit/receive strength, atmospheric effects and form factors. Contact us with your requirements and we will recommend a cost effective solution.
-
Product
BRI, PRI and PSTN FXS Simulator
emutel Max
-
emutel Max is a standalone or rackmount unit that comes in five variants giving 8 BRI, 2 PRI and 8 BRI, 2 PRI and 15 BRI, 8 BRI and 14 analogue or 2 PRI, 8BRI and 14 analogue. emutel Max can emulate different country specific networks by adding network personality cards " networks supported include North American, NTT, Euro-ISDN, VN3, ITR6 and BTNR191. Protocol analysis option is also available on emutel Max.
-
Product
Oxygen Sensor Tester and Simulator
ST05
-
The sensor signal output is shown in real time on the bar graph, while a 2 digit alphanumeric display shows the sensor output cross count per second. By pressing the ?Test? button and performing a snap throttle acceleration of the engine, it tests the response time of the sensor and shows a pass or fail result within seconds. Two buttons allows for simulation of rich or lean conditions to monitor response of the engine control module.
-
Product
Linktropy Network Delay Simulator
-
Linktropy Emulators Provide Affordable Network Emulation for Accurate, Repeatable Performance Testing at Speeds up to 1 Gbps
-
Product
Modular Solar Array Simulators
MP4300A Series
-
The output power of solar cells varies with numerous environmental conditions (e.g., temperature, irradiation) and operational conditions (e.g., eclipse, spin). The Keysight MP4300A Series solar array simulator enables you to test all these conditions with high accuracy. It delivers fast current-voltage (I-V) curve changes with a quick recovery time, emulating rapidly changing conditions.
-
Product
MAX31855 J-Type Thermocouple Sensor Breakout
SEN-30001-J
-
Breakout board for the MAX31855J digital thermocouple interface IC. Measured temperature range is -210C-1200C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 1x5 pin header, has a vertical mini thermocouple connector and four mounting holes for standoffs and 4-40 screws.
-
Product
Thermocouple Power Sensors
N8488A
Power Sensor
N8488A power sensor has the widest frequency range among N8480 power sensors offering from Keysight.
-
Product
K-type Thermocouple to Digital Converter
THERMO K click
-
THERMO K click carries the MCP9600 IC from Microchip. Depending on the type of probe it uses the click can measure temperatures from −200 °C to +1372 °C.
-
Product
Circuit Simulation Software
SIMetrix/SIMPLIS
-
SIMetrix/SIMPLIS is an advanced simulation tool optimized for efficient design of power electronics circuits. SIMetrix/SIMPLIS combines accuracy and convergence in a unique and powerful design environment, enabling 10-50x faster simulation for power supply designs. SIMetrix is a mixed-mode circuit simulation package designed for professional electronics engineers. SIMetrix comprises a substantially enhanced SPICE simulator, schematic editor and waveform viewer in a unified environment.
-
Product
Mouth Simulator
BO1032
-
As consumers demand smaller devices that produce better sound and need better microphones, you need to test your microphones using more than a simple 1kHz tone. Sweep tests require a good mouth simulator that can produce a sweep with a known steady SPL.
