Solenoid
Act as a magnet when current flows through moving an iron core.
-
Product
PXI Single 16x4 1-Pole 5A Power Matrix
40-549-001
-
The 40-549 is a single pole power matrix module, suitable for switching inductive/capacitive loads up to 5A with 110VDC/250VAC hot switching and 400VDC/250VAC cold switching. It is available in single 16x4, single 8x8, dual 8x4 or single 8x4 configurations. Connections are made via a front panel 25 way D-type male connector. Power Matrix Modules are intended for switching heavy AC or DC loads or for slaving large external relays, contactors and solenoids. The module is suitable for applications requiring switching of either mains voltage or DC current.
-
Product
PXI SPST Switch: 100-ch, 100Vrms/1A, Reed Relays
M9133A
-
The M9133A is a high-density, general purpose switch with 100 independent, single-pole, single-throw (Form A) switches in a single PXI module. This module can be used to cycle power to products under test, control indicator and status lights or actuate external power relays and solenoids. The high-speed, long-life reed relays can handle 100Vrms and 1A, with up to 25W power. Choose from the durable connector block or the standard cable connections.
-
Product
Electrical Testers
-
Actron is an industry leader in electrical testers for your car or home repair projects. Pick your choice of Actron’s digital multimeters to help pinpoint problem areas and determine which components need repair or replacement. Find shorted and open wiring with the help of our circuit testers. Troubleshoot fuel injectors, solenoids, and digital sensors with the Actron Automotive Logic Tester. Use Actron IR thermometers to check AC systems, brakes, catalytic converters, cylinder heads, and overheating electrical components. Use the Actron Videoscope to inspect hard to reach areas. Measure and set spark plug timing on older vehicles, tractors, lawn mowers and more using Actron timing lights. Find bad batteries and faulty charging systems with Actron Battery Load Testers. Our Remote Starter Switches allow one person to conduct tests while cranking or starting the engine.
-
Product
Single 8-Channel 1-Pole 16 Amp PXI Power Multiplexer
40-662-013
-
The 40-662 range of 16 Amp PXI power multiplexer modules is available in seven configurations ranging from 4-off 2:1 multiplexers to 1-off 16:1 multiplexers. Power multiplexer modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. All versions are suitable for switching loads up to 16 Amp at 250VAC. User connections are made via a 20-way GMCT plug which is fully support by our comprehensive range of cables and connector accessories.
-
Product
WINDING COIL TURNS TESTER
VE201R
-
Winding Turns Tester for Counting Measuring Number of Turns for Air Core Coils, Bobbin Coils or Solenoid Coils. Can Measure : Turns along with Winding Polarity and DC Resistance.Turns Measurement : 1 Turns to 80,000 Turns
-
Product
PXI 100 x SPST Ruthenium Reed Relay Switching
40-140A-221
-
This range of high density reed relay switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose reed relays are suitable for the construction of small switching networks, for slaving up to larger switches or for operating external devices (e.g. lamps, solenoids etc.).
-
Product
PXI 8 Bank 8 Channel 2 Pole Multiplexer
40-659-102
-
Model 40-659 is an 8 Bank 8 Channel Multiplexer module with 2-pole switching, It uses high quality electromechanical relays and is suitable for switching signals up to 2Amp, 300VDC/250VAC.The 40-659 module is suitable for multiplexer applications where two signals are required to be switched simultaneously, for example send and return signals in a telecoms system. It is also suitable for applications where reed relay based multiplexers do not have sufficient power handling capability such as switching medium power AC or DC loads or for slaving external relays, contactors and solenoids.
-
Product
PXI SPDT Switch: 26-ch, 2A, Armature Relay
M9130A
-
The M9130A is a general purpose switch with 26 independent, single-pole, double-throw (Form C) switches in a single PXI module. This module can be used to cycle power to products under test, control indicator and status lights or actuate external power relays and solenoids. The armature relays can handle up to 60W power. When needed, these relays can handle up to 6A pulsed carry current. Choose from the durable connector block or standard cable connections.
-
Product
20 Channel Actuator/GP Switch Module for 34970A/34972A
34903A
-
The Keysight 34903A is a general-purpose switch module for the 34970A/34972A Data Acquisition/Switch Unit. It has 20 independent single-pole, double-throw (SPDT) relays and is used to cycle power to products under test, control indicator and status lights, and to actuate external power relays and solenoids. Combine it with matrix and multiplexer modules to build custom switch systems. Its 300 V, 1 A contacts can handle up to 50 W, enough for many power line switching applications.
-
Product
PXI Multiplexer, Very High Power DC, 4-Channel, 40A, 14V
40-664A-001
-
The multiplexer is suitable for switching heavy loads or for slave switching large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of DC voltage at high current.
-
Product
PXI Multiplexer, Very High Power DC, 4-Channel, 20A, 28V
40-664A-002
-
The multiplexer is suitable for switching heavy loads or for slave switching large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of DC voltage at high current.
-
Product
PXI 100 x SPST Electromechanical Relays
40-145-201
-
The 40-145/46/48 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose relays are suitable for the construction of small switching networks, I/O port switching, for slave switching larger relays or for operating external devices (e.g. lamps, solenoids etc.).
-
Product
PXI Semi-Dynamic Digital I/O Module, 64-Channel
40-419-001
-
The 40-419-001 is a 64-channel digital I/O module suitable for operating external devices, such as power, RF and high voltage relays, solenoids and lamps. It can also be used for interfacing with external logic such as a programmable instrument with a BCD interface depending upon the module’s driving capabilities.
-
Product
Linear Motion Potentiometers
-
A spin-off of the Trimpot trimming potentiometer product line, the linear motion potentiometer was developed to meet the needs of designers wishing to detect movement of position. Applications for these compact components include: Solenoid positioning sensors for automated controllers, volume control on audio equipment, joystick controllers, satellite dish positioning, and robotics.
-
Product
High field Superconducting Magnets
-
Cryogenic Ltd manufactures a wide range of superconducting magnets for research and industrial purposes. A range of standard solenoids between 1 to 22 Tesla is produced, and in addition split pair solenoids in the range 1 to 14 Tesla, with a typical central field homogeneity of 0.1%.
-
Product
PXI 2 Amp Multiplexer, 8-Bank, 8-Channel 2-Pole
40-659A-102
-
Model 40-659A is an 8 Bank 8 Channel Multiplexer module with 2-pole switching, It uses high quality electromechanical relays and is suitable for switching signals up to 2Amp, 300VDC/250VAC. The 40-659 module is suitable for multiplexer applications where two signals are required to be switched simultaneously, for example send and return signals in a telecoms system. It is also suitable for applications where reed relay based multiplexers do not have sufficient power handling capability such as switching medium power AC or DC loads or for slaving external relays, contactors and solenoids.
-
Product
Contacting Linear Motion
-
A spin-off of the Trimpot trimming potentiometer product line, the contacting linear motion position sensor was developed to meet the needs of designers wishing to detect movement of position. Applications for these compact components include: Solenoid positioning sensors for automated controllers, volume control on audio equipment, joystick controllers, satellite dish positioning, and robotics.
-
Product
PXI 5A Mux 4-Bank 11-Ch Isolated COM
40-651-013
-
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel. 4-bank 11-channel. 8-bank 5-channel.Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
Product
NI-9475, 60 V, 8-Channel (Sourcing Output), 1 µs C Series Digital Module
780132-01
-
60 V, 8-Channel (Sourcing Output), 1 µs C Series Digital Module - The NI‑9475 works with a variety of industrial devices such as solenoids, motors, actuators, relays, and lamps. Each channel sources up to 1 A at levels up to 60 VDC and features isolation from … channel‑to‑earth ground.
-
Product
NI-9477, 60 V, 32-Channel (Sinking Output), 8 µs C Series Digital Module
780174-01
-
60 V, 32-Channel (Sinking Output), 8 µs C Series Digital Module - The NI‑9477 works with industrial logic levels and signals to connect directly to a wide array of industrial relays, solenoids, and motors. Each channel is compatible with signals from 5 V to 60 V and … features isolation from channel‑to‑earth ground. You can wire the NI‑9477 channels in parallel to sink up to 20 A of current per module (1 A per channel maximum).
-
Product
Electric Linear Actuators
MaxJac
-
The MaxJac actuator features a smooth high response ball screw and gear motor and utilizes a proprietary guidance bushing to provide precision smooth linear actuation. Standard equipment includes a 12 volt motor with potentiometer feedback. It is ideal for throttle control, solenoid actuation, and valve actuation in such applications as construction equipment, motor vehicles, marine, and blood infusion pumps.
-
Product
Single 4x4 1-Pole 16 Amp PXI Power Matrix With Loop-Thru
40-552-011
-
The 40-552 range of 16 Amp PXI power matrix modules is available in four configurations with matrix sizes of 8x2 and 4x4 and the ability to expand the matrix size with the Y-Axis loop-thru connections: e.g. 8x4, 12x4, 16x4, etc. (with 4x4 matrices) or 16x2, 24x2, 32x2, etc. (with 8x2 matrices). This range is capable of switching up to 16 Amps and up to 300VDC/250VAC hot switching and 400VDC/250VAC cold switching. These PXI power matrix modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors, and solenoids.
-
Product
PXI 50 x SPST Electromechanical Relays
40-145-001
-
The 40-145/46/48 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose relays are suitable for the construction of small switching networks, I/O port switching, for slave switching larger relays or for operating external devices (e.g. lamps, solenoids etc.).
-
Product
PXI 8 x DPDT Power Relay Module, 5A
40-157-001
-
40-150/151 modules have 8xDPST or 12xDPST power relays, suitable for switching inductive/capacitive loads up to 5A at 250VAC. 40-155/156 modules have 8xSPDT or 16xSPDT power relays and 40-157 is configured as 8xDPDT. Power relay modules are intended for switching heavy AC or DC loads or for slave switching large external relays, contactors and solenoids. The 40-150 series of power relay module are suitable for applications requiring switching of either mains voltage or DC current.
-
Product
Mass Flow Controller
SEC-E Series
-
This general purpose mass flow controller has a reliable thermal sensor and solenoid valve, allowing you to achieve high-level control of gas flow. A versatile component, the mass flow controller sec-e series can be used in a wide range of industries.Gas flow through the mass flow controller can be controlled over a range of flows: from 10 SCCM to 200 SLM.
-
Product
Walk / Drivable test facilities
TW / CW series
-
Walk or drive-in temperature and climatic test chambers can be designed from CTS by a standardized grid system affordable in all sizes. The refrigeration performance data are adjusted here by our experienced sales and project engineers on your testing out. The walk / drive-chambers are ideal for larger components and finished products. CTS as a medium sized company attaches great importance to the detail quality of the equipment components, with only the best supplier products such as compressor and solenoid valves are used. Your resulting advantages are trouble-free long-term operation and thus no loss of valuable test time.
-
Product
Test & Support Gear
-
Atec has experience with rugged and reliable equipment required for oil-field applications and the reputation for customer responsiveness and quick deliveries. Our energy history includes several years of re-engineering and manufacturing several test and support energy products. We have the ability to design, re-engineer and assemble items such as: junction boxes, cables, harnesses, printed circuit boards, computer systems, data acquisition software, valves, solenoids, & gear boxes.
-
Product
PXI 20Amp 28Volt 2xSPST Automotive Relay
40-180-011
-
Models 40-180/181 are High Power Relay Modules available with 2 SPST, 4 SPST or 2 SPDT contacts. They are capable of switching inductive/capacitive loads up to 40A at 14VDC or 20A at 28VDC.The 40-180/181 High Power Relay Modules are suitable for switching heavy loads or for slaving large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of D.C. voltage at high current. The 28V version is suitable for truck system test applications.
-
Product
PXI 16xSPST 16A Power EMR Module
40-161-001
-
These Power Relay Modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. The 40-161 is ideal for switching up to 16A in both AC and DC applications.
-
Product
PXI General Purpose 2A Relay Module 19xDPST
40-132-202
-
Pickering Interfaces 40-131/132 modules are a range of low cost, general purpose electromechanical relay cards. They are capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching cards do not have sufficient voltage or current carrying capability. Applications include the switching of medium power AC and DC loads, or slave switching larger relays, contactors or solenoids. Connections are made to the card via a front panel mounted 78 pin D-Type connector plug.
