Diode Testers
See Also: Diode Test
-
product
SCR Diode Testers
SCRs and Diodes are used in the power sections of various power systems. A SCR Diode Tester is an important piece of equipment to determine if a SCR or a diode is defective in a power circuit. It is difficult and time-consuming to troubleshoot SCRs and Diodes with a digital meter.
-
product
Bypass Diode Tester
BDT
Our bypass diode thermal tester is designed to assess the adequacy of the thermal design and long-term reliability of PV modules bypass diodes, which are used to limit the detrimental effects of module hot spot susceptibility.
-
product
Diode Tester
FEC VF40CM
Frothingham Electronics Corporation
The VF40CM is intended for testing VF, HALF CYCLE SURGE, and THERMAL RESPONSE/RESISTANCE on small- and medium-power diodes and rectifiers. It can also measure THERMAL RESPONSE/RESISTANCE on NPN and PNP bipolar transistors using an external user-supplied VCB supply.The VF40CM also is sometimes used to measure VZ of low-voltage zener diodes up to the compliance voltage limit of the tester. 20V at 20A is possible.
-
product
Photovoltaic System Bypass Diode Tester
FT4310
Hioki is pleased to announce the launch of the Bypass Diode Tester FT4310 for Photovoltaic Systems. The FT4310, which is designed to test bypass diodes in strings of crystalline photovoltaic cells, can be used to detect open and short-circuit faults in bypass diodes by string either in daylight or at night. The instrument is the first portable device capable of detecting bypass diode open faults in operating panels (without requiring the panels to be shielded from sunlight).
-
product
Measurement & Diagnostic Products
DURST Motor & Electric Industries Pty Ltd.
DURST Measurement & Diagnostic Products; circuit tester, vehicle battery analyzer, multimeter, dedicated automotive multimeter, clamp meter, sound level meter, oxygen sensor tester, diesel engine tachometer, multisystem ignition analyzer, faultfinder, circuit tester, diode tester, regulator tester, growler for testing motor insulation, armature/commutator tester, diagnostic testers, current clamps, optical photo/contact tachometer, etc.
-
product
Diode Tester
FEC200E
Frothingham Electronics Corporation
The FEC200E is an automatic computer- controlled diode and rectifier tester. It is controlled by a standard PC-compatible computer running FreeDOS.
-
product
Gearbox Tester
The gearbox tester was designed to test the Azimuth Drive Unit (ADU) for a missile launcher. The ADU is the horizontal position controller for the launcher. It consists of a main drive shaft, a manual drive shaft and an output drive shaft. This system uses a multi-axis motion controller to operate.
-
product
Bit Error Rate Tester - MATRIQ
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
product
KVS Rugged Igniter Tester With Current Monitor
4314
The Valhalla Scientific Model 4314 KVS Digital Igniter Tester is designed to provide extremely safe and reliable resistance testing of explosive or volatile devices. Proven uses include fuses, squibs, igniters, explosive bolts, automobile airbag initiators and many others.
-
product
MXE EMI Test Receiver, 3 Hz to 44 GHz
N9038B
The Keysight N9038B is a standards-compliant MXE EMI test receiver and diagnostic signal analyzer built on an upgradeable platform. You choose the frequency coverage you need to fully test devices with outstanding accuracy and sensitivity across required ranges.
-
product
64 Gbaud High-performance BERT
M8040A
The Keysight M8040A is a highly integrated BERT for physical layer characterization and compliance testing. With support for PAM-4 and NRZ signals and data rates up to 64 Gbaud (corresponds to 128 Gbit/s) it covers all flavors of 200 and 400 GbE standards.
-
product
ABex PXI to Analog Bus Bridge with Digital IOs
ABex AM-300 Controller
The ABex system controller ABex AM-300 is required to control the analog bus of a ABex chassis. It is used as an interconnection bridge between PXI and ABex backplane.In addition it features a whole bunch of additional functionality. Despite the 96 open drain outputs it has galvanically isolated IOs, and communication interfaces.
-
product
PAM4 Bit Error Rate Tester.
BERT-1102
The BERT-1102 is a 4 or 8-channel PPG and Error Detector for the design, characterization and manufacturing test of optical transceivers and opto-electrical components with symbol rates up to 29 GBaud/s in both NRZ and PAM4 formats. With scalability and exceptional signal fidelity, it is a cost-effective test solution for up to 400 Gb/s communication eco-systems.
-
product
Hoist Tester
The system has the capability of operating hyraulic powered hoists, DC powered hoists and 400Hz AC powered hoists. When a unit is connected to the system it is automatically detected and the system will load the unit's control software, acceptance procedures and operational safety limits. By doing all of this the operator does not need to worry about anything other than installing the unit and clicking Run to execute a full test procedure.
-
product
MTM-Bus Tester
PXIe-1149.5
The Corelis PXIe-1149.5 is a versatile, multi-mode instrument for interfacing with MTM-Bus modules. The PXIe-1149.5 adds MTM-Bus master, slave, and monitoring with full IEEE-1149.5 electrical and protocol compatibility with a standard PXIe interface for convenient integration into any Test Program Set (TPS).
-
product
Bit Error Rate Tester - PXI
BERT 1001/1005 Series
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
product
Universal A/V Tester
This tester was built for our client with the specific requirement that specific UUTs can be added to the system by our client. We handled developing test software for the first 2 UUTs utilizing an open programming structure that allowed programming modules to be strung together to create test programs for any additional UUT that our client wants to add in the future.
-
product
TVS Diodes
Power TVS diodes provide outstanding protection for both alternating current and direct current power line applications by a Power TVS diode in a surface mount package. When compared to other devices, such as MOVs, power TVS diodes provide much better protection. Bourns provides a broad voltage range of devices with surge current ratings ranging from 3, 6, 10, and 15 kA to suit a variety of applications.
-
product
Diode Lasers
Offering diode lasers in a wide range of wavelengths, power, and package configurations. Providing optimum solutions for applications in laser pumping, materials processing, medical, defense, and instrumentation.
-
product
Diode Scanner
SC924
Frothingham Electronics Corporation
The SC924 is an electromechanical device for testing diodes loaded on burn-in boards.A set of Kelvin contacts is indexed from diode to diode. The contacts move over a range of 24 inches in the X direction and the table holding the boards moves over a range of 9 inches. This allows scanning of multiple burn-in boards or boards with multiple rows of diodes.
-
product
Steering Diodes
ProTek's low capacitance Steering Diode Arrays provide high-speed data line and I/O port protection from transients caused by Electrostatic Discharge (ESD), Electrical Fast Transients (EFT), Tertiary Lightning and other induced voltages. Steering diodes divert the transient to the power-bus or ground and away from sensitive IC components.
-
product
Diode Power Sensor
8481D
The 8481D diode power sensor measures average power over the frequency range 10 MHz to 18 GHz and power range -70 to -20 dBm (50 dB dynamic range).
-
product
Automated Coherent Receiver Tester
CoRx Tester.
Quantifi Photonics’ CoRx Tester provides automated measurement of key coherent receiver performance parameters. The CoRx Tester is comprised of a pre-configured PXI chassis, a two-channel tunable laser, a polarization controller, and a two-channel Variable Optical Attenuator (VOA) with built-in power meter. Just connect the two optical outputs to your Integrated Coherent Receiver (ICR), connect your ICR to the oscilloscope and let the CoRx Tester software do all the rest.
-
product
Point Contact Diodes
SemiGen’s 1N Series of Point Contact Mixer Diodes are designed for applications through KA band. Each device in this series is specially designed for low noise gure, impedance and VSWR. Our devices are drop in replacements for all military and commercial requirements. These diodes employ epitaxial silicon grown in a speci c reactor for optimized performance. They are suitable for use in stripline applications.
-
product
Limiter Diodes
The SemiGen SLP7100 series of Limiter Diodes are processed with a high-resistivity epi that have thin intrinsic layers. These devices are typically in the 2 to 20 micron range of epi thickness and can be gold doped to achieve specific performance goals. These diodes are used in passive or active limiter designs in the 100 MHz to 30 GHz frequency ranges. They are ideal for use in high-power applications and can be supplied in chip form or in your choice of packages below.
-
product
Laser Diode
Is an electrically pumped semiconductor laser in which the active laser medium is formed by a p-n junction of a semiconductor diode similar to that found in a light-emitting diode.
-
product
Three-Path Diode
NRPxxS/SN/SN-V
The R&S®NRPxxS/SN power sensors use three separate diode paths, each operated in the optimum detector range. As a result, the average power can be determined with high accuracy independent of the modulation type. Measurement results are hardly affected by interfering signals or harmonics.
-
product
Power Diodes
Renesas power diodes support the high performance and small size and weight of mobile and information devices.
-
product
Laser Diode Driver
Fibotec offers special laser diode drivers, especially versions that accommodate laser diodes via integrated terminal bases. Two standard products for different applications accommodate laser diodes in butterfly packages with up to 2 A forward current. The "Pump Laser Pinout" is standard. The configuration for "Signal Laser" is available on request.
-
