Relay Drivers
Control the energized state of relays.
-
Product
Battery Monitor Relay
BMR
-
The Battery Monitor Relay contains over under voltage sensors combined with positive and negative ground detection.
-
Product
Diagnostic Relay Buddy 12/24
192
-
Relay Buddy 12/24 is a quick go / no-go tester for the most common automotive relays. This new version Relay Buddy tests both 12 and 24 volt relays. If the relay fails the test, 3 different trouble codes will advise you of the possible causes for the failed relay. The red LED will flash once, twice or three times to indicate the problem. Trouble code definitions are printed on the back of the tester for your convenience.
-
Product
SIMRC - 8 x 2 Matrix 1-Pole Screened Relay
1030-R-8-2-1RF-5/1D
Matrix Switch Module
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
Product
NI-9485, 8-Channel, SSR Relay, 60 VDC/30 Vrms, 750 mA C Series Relay Output Module
779600-02
Relay Output Module
The NI-9485 allows for direct connection to a wide array of industrial devices such as motors, actuators, and DC devices. Each channel provides access to a solid state relay (SSR) for switching voltages up to 60 VDC/30 Vrms with switching current up to 750 mA per channel or up to 1.2 A on four channels. Each channel also features channel-to-channel isolation.
-
Product
Big Easy Driver
-
The Big Easy Driver, designed by Brian Schmalz, is a stepper motor driver board for bi-polar stepper motors up to a max 2A/phase. It is based on the Allegro A4988 stepper driver chip. It's the next version of the popular Easy Driver board.
-
Product
Switch Modules - 32 Single Pole Relays Arranged as a 16x2 Matrix
JX32/AB-1
Switch Module
This module has 32 single pole relays arranged as a 16x2 matrix as shown in the figure to the left. The matrix may be operated and wired individually for up to 16 16x2's per chassis, or jumpered to the backplane to form up to a 256x2 matrix. It is available with Type S or M reed relays for high speed, long life application.
-
Product
Dual Relay Trip Amplifier for RTD and Slidewire Sensors
SEM1633
-
The SEM1633 provides an accurate alarm / switching function when used with RTD or Slidewire sensors. Other sensor characteristics or your own 22 point linearization characteristic (for slidewire or linear resistance) can be downloaded into the product enabling you to adapt it exactly to your application.
-
Product
8 Channel 1GHz High Frequency for SBDT Relay Module
DP-cPCI-4158
-
DP-cPCI-4158 is a 8 channel high frequency SPDT relay module. It provides for 1000V DC isolation between channels. This module is constructed using SPDT relays.
-
Product
PXI/PXIe Fault Insertion Switch, 74-Chan 2A, N/C Through Relays, Fault Buses on M & U
42-190C-012
Fault Insertion Unit
The 40-190C-012 (PXI) and 42-190C-012 (PXIe) are fault insertion switches with 74 channels. They are part of a range of modules available with 74, 64 or 32 channels and are primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
PCI 16 Reed Relay Output Digital Interface
8003
-
The 8003 PCI digital I/O interface provides 16 Reed relay outputs provide high quality, long-life, low current (10 Watt maximum), dry contact switch closures. Reed relays are well suited for low-current applications. The relays are normally open, and close when energized. Writing a 1 to the proper port bit can individually energize each relay.
-
Product
Power Calibrator And Protection Relay Test Set
CP11B
-
Calmet Smart Calibration Devices
Single phase, class 0.02 and 0.05 power quality calibrator up to 120A and 560VAC with programmable power quality parameters. It makes possible to make automatic test of electricity meters, measurement transducers, current transformers and protection relays.
-
Product
Four Channel Relay Board for Power Supply Isolation
FXA-113 PSU Relay 4CH
Power Supply
The FXA-113 is a four-channel relay board designed as an output disconnect option for laboratory power supplies. Especially in ICT applications it’s important, that the power supply is completely isolated from the DUT during measurements. Therefor each channel features two high current relays for the power path and two reed relays for the sense path. All four channels are equipped with a status led and can be switched independently. In addition, it is delivered with an installed DIN rail carrier.
-
Product
Replacement of Legacy Instruments with New Compatible Instruments, without Modifying the Existing Software, Drivers, or TPSs
WinTE 7000
-
Replacement of legacy instruments with new instruments, without modifying the existing software, drivers, or TPSs.
-
Product
Single Phase Universal Protection Relay Test Set
S100A
-
S100A is the Universal Single Phase Protection Relay Test Set with 1*100A and 3*150V output, local control system for basic relay testing with manual operation.
-
Product
40 Channel Low Thermal Relay Multiplexer Module
DP-cPCI-4017
-
DP-cPCI-4017 is a 40 Channel Relay Multiplexer module constructed using ‘2 Form A’ relays. The DP-cPCI-4017 is implemented as a 6U cPCI module. As a 40 channel multiplexer, one input can be multiplexed to any of the forty outputs or vice versa. The forty channel multiplexer is divided into 4 banks of 10 channels each. This combination allows the board to be used as one group of 40x1 or two groups of 20x1 or four groups of 10x1 multiplexer. The banks are isolated from each other using tree switches. Four tree switches are used, one tree switch for each bank.
-
Product
Switch Drivers
-
Macom Technology Solutions Holdings Inc.
MACOM’s switch drivers bridge the gap between digital control signals and the analog voltages and currents required to drive our extensive family of RF, microwave and millimeter wave PIN diode and FET switches.
-
Product
PXI 50 x SPST Electromechanical Relays
40-145-001
Relay
The 40-145/46/48 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose relays are suitable for the construction of small switching networks, I/O port switching, for slave switching larger relays or for operating external devices (e.g. lamps, solenoids etc.).
-
Product
SLED Source Driver
S-108
-
SLED Source & Driver slot module of FOTS system is an efficient module that can drive a stable high power broadband source and modulate a high power SLED to output a high bit rate optical signal. As a high power broadband SLED source, this module can drive the maximum output power of more than 14 dBm and has a stable wideband source characteristics of >90nm@-20dBm/nm. As a high current (400mA) modulation technique, it shows a high power and high bit rate digital signal of > 155 Mbps with > 13 dBm peak power.
-
Product
Loop Powered Trip Amplifier With Dual Relay Output
SEM1636
-
The SEM1636 monitors a (4 to 20) mA loop and provides two independent change over trip contacts set to trip at any point within the (4 to 20) mA range.
-
Product
Battery Voltage Relay
BVR
-
Battery Voltage Relays supply alarm indications at precise voltages for undervoltage and overvoltage conditions. The BVR is designed to prevent damage and incorrect operation during anticipation transient conditions.
-
Product
Shimadzu GC Driver For Chromeleon™ 7.2
-
Thermo Scientific™ Chromeleon™ 7.2 Chromatography Data System (hereinafter called Chromeleon) Software can control the Nexis GC-2030 and HS- 20/HS-10 Headspace sampler with the driver software. Shimadzu GC-2030 and HS-20/HS-10 instrument parameters can be set seamlessly via the Chromeleon 7.2.
-
Product
SUPER-LIGHT Three-phase Relay Test Kit
L336i-E
-
PONOVO’s L336i-E protection relay test equipment, is the three-phase relay test kit with small size and light weight, only 8.6kg.
-
Product
Relay Test Equipment
MC3000 Series
-
MC3000 is recently developed relay test equipment. There are 3 sub-models, MC3000A, MC3000B and MC3000C. They are low cost oriented, aimed to provide customers cheap and cost-effective products.
-
Product
Automatic Relay Test Set
DRTS 66
-
DRTS 66 is the most powerful diagnostic test set designed to perform accurate tests on protection relays, transducers, energy and power quality meters. This advanced test equipment is also thought to satisfy all the needs related to commissioning and substation maintenance. 6 Current and 6 Voltage generators simultaneously available.
-
Product
Chassis - up to 8 8x1 Modules, 16 4x1 Modules or Mixtures of 8x1's, 4x1's, 2x1's & 2x2 Modules in Any Combination or Configuration for up to 64 Relay Drives
CXM/64-MF
Chassis
These Chassis controls up to 8 8x1 modules, 16 4x1 modules or mixtures of 8x1"s, 4x1"s, 2x1"s and 2x2 modules in any combination or configuration for up to 64 relay drives. LEDs on the front panel show switch and power status. Add Switch Modules, display / driver modules and a Control Module to complete the system or simply buy the chassis wired out to D connectors to control your own relays. A manual control is optional.
-
Product
Relay I/O Modules
XTA Series
-
These modules are intended for use with BusWorks XT Series discrete I/O or other digital output modules for the purpose of driving high energy loads.
-
Product
16-CH Latching Relay Outputs & 16-CH Isolated DI Card
PCI-7256
Analog Output Module
- Supports a 32-bit 3.3 V or 5 V PCI bus- 16-CH latching SPDT relay outputs- Power saving on relay actuation- Output status unchanged when power-off- On-board LED indicators for relay status
-
Product
Low capacitance SIL reed relays
Series 103
-
Low Capacitance SIL relays. Requires a board area of 0.25 x 1.0 inches (6.4mm x 25.4mm). Form A with one fifth the usual switch to coil capacitance
-
-
Product
PXI SPDT Switch: 26-ch, 2A, Armature Relay
M9130A
Switch Module
The M9130A is a general purpose switch with 26 independent, single-pole, double-throw (Form C) switches in a single PXI module. This module can be used to cycle power to products under test, control indicator and status lights or actuate external power relays and solenoids. The armature relays can handle up to 60W power. When needed, these relays can handle up to 6A pulsed carry current. Choose from the durable connector block or standard cable connections.
