CompactPCI Controllers
-
Product
PC Controlled Low Voltage Tester
Cablescan S32
-
The Cablescan S32, with a 32-board Expansion Cabinet, may be ordered with 1 to 32 low-voltage 128-point scanner boards. Fully loaded with scanner boards, this tester provides 4096 test points.
-
Product
DC Bias and RF Stimulus Control Module
Quantum SMART Fixture
-
Accel-RF Corporation, the world leader in turnkey RF automated reliability test instruments, has "unplugged" the industry-leading RF SMART Fixture from their automated test platform and made it available for benchtop test. The NEW Quantum SMART Fixture is a programmable self-contained DC bias and RF stimulus control module capable of synchronizing sequenced independent pulsed-bias and pulsed-RF signals to a DUT or remote fixture. The signals are controlled from a user interface compatible with Accel-RF's LIFETEST software. The Quantum SMART fixture is capable of "active" temperature control and monitoring of a remote DUT through embedded firmware in the microprocessor
-
Product
Rugged Conduction Cooled 3U CompactPCI Processor Blade with Quad-Core Intel® Atom™ Processor
CT-3620
Processor Blade
The ADLINK CT-3620 Series is a Rugged Conduction-Cooled 3U CompactPCI processor blade in single-slot (4HP) width form factor featuring a quad-core Intel® Atom™ SoC and soldered DDR3L-1333 ECC memory up to 4GB. Graphics is integrated graphics on the CPU and storage is provided by an onboard 32GB SSD. Rear IO signals include 2x GbE, 1x USB 2.0, VGA, 2x COM, and 1x SATA 3Gb/s, providing for expansion with an optional Rear Transition Module (RTM).
-
Product
Source Phase Control
S93088B
-
The S93088B allows users to set calibrated, arbitrary phase differences between two signal sources. The sources can be the analyzer’s internal sources or external signal generators routed through the analyzer’s test set. The phase difference can be fixed, or swept between two specified phase values. S93088B also controls the relative power level between the sources using the receiver-leveling feature.
-
Product
Flight Control System Test Platform
Test Platform
The Flight Control System Test Platform provides a hardware in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of Flight Control Systems (FCS) of both commercial and military aircraft. The system simulates control surface activities from multiple combinations of rudder, flaps, elevator, aileron, and engine controls to the FCS. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation test systems.
-
Product
Network Interface Controllers for Anonymous Subscriber Messaging (FC-ASM)
Fibre Channel
-
Avionics Interface Technologies
FC-ASM Network Interface Controllers for Avionics applications. The AIT FC-ASM NIC solutions are Quad interface modules providing 4 independent NIC interfaces on a single module. All FC-ASM and Fibre Channel protocol operations are handled onboard, providing an efficient, high bandwidth, FC-ASM protocol offload solution for 1Gbp/s and 2Gbp/s FC-ASM.
-
Product
IO-Link Sensors for Motion Control
-
Encoder for precise position determination and linear measurement, Defined pulse sequence for the reliable detection of rotational speeds, Inclination sensors for precise measurement of angles of inclination on X and Y axes, High measurement accuracy across the total angular range in two axes, High protection rating for the requirements of harsh industrial environments
-
-
Product
EZ-Glider Position Control Telescoping Torque Arms
-
The position control telescoping torque arms help manufacturers detect and eliminate costly screw-fastening errors during the assembly process. Position Control telescoping torque arms are designed to reduce the risk of improperly fastened screws, ensuring that every screw is in the correctly tightened in the correct sequence. Using the EZ-Glider Position Control torque arm is like putting the eyes and ears of a quality control manager where they are needed most - right on the assembly area.The EZ-Glider Position Control telescoping torque arm consists of a torque reaction arm with encoders mounted at the base and a control box. The control box is used for programming and it tracks the axis movement by converting angle counts to the precise position of the screwdriver. The location is calculated from encoder values, allowing the operator to easily teach the torque arm a programmed sequence pattern and then use it to control the assembly process
-
Product
[5kV AC/6kV DC] Hipot and Insulation Resistance Tester, Rise/Fall-Time Control Function Equipped
TOS5300 Series
-
The "TOS5300 Series" is a series of test instruments used in Hipot (withstanding voltage) tests and insulation resistance tests, two of the four tests regarded as necessary for ensuring the safety of electrical products. With an output of 5 kV/100 mA (AC) and 6 kV/10 mA (DC), the series can be used in Hipot (withstanding voltage) & insulation resistance testing of electronic equipment and electronic parts, based on the requirements of IEC, EN, UL, VDE, JIS, and other international safety standards and the Electrical Appliance and Material Safety Law. Also, the test voltage stability is improved with the adoption of a newly developed switching amplifier. Since the output voltage can be kept constant even when the AC line voltage or frequency changes, consistent testing can be performed, even when the power supply environment is in an unstable region. The TOS5300 is also equipped with a number of features that are capable of meeting a variety of test needs. It is a new low-cost standard model that provides thorough operability, reliability and safety.
-
Product
Spectrally Controlled Interferometry For Measurement And Analysis
SCI
-
Directly measure all surfaces and angles in one setup, for an ROI of < 1 year.
-
Product
Communication and Control
-
Measure Tech designs and manufactures push button switches, volume controls (RVDT), and knobs for Airbus, Boeing and Bombardier aircraft.
-
Product
High Flexibility Test Controller Card
TCC 1800-UE
-
The TCC1800-UE Test Controller Card is a generic control board for production testing of printed circuit boards (PCBs). The board is controlled by a command language on a PC to which it is connected via Ethernet.The TCC1800-UE is designed to work with positive voltages up to 24V. The card provides extensive IO: Analog and digital interfacing, counters, PWM outputs, bidirectional I/O, ethernet-, CAN, USB, SPI and I2C interfacing.
-
Product
3U CompactPCI Serial 4-slot SSR w/o RTM w/ Ethernet
1CPCIS-304-R200
-
3U CompactPCI Serial Backplane with 4 CompactPCI S.0 slots, system slot right, without rear IO : 1x CompactPCI S.0 CPU slot, 3x CompactPCI S.0 peripheral slots, without connectors for RTMs (RearTransition Modules), Ethernet full mesh.
-
Product
Automated Visual Control System for Canned Food in Glass Containers
-
The system is designed for visual quality control of food packaging products. The level of filling the jar with the product, as well as its closure, is monitored. During the development of the system, smart cameras from Sick were used, but a special illumination of our design was used to improve the image quality.
-
Product
Remote Control Light & Air Brake Tester
Express Garage
-
The Express Garage Trailer Air and Electrical Systems Tester is a tool that anyone with even basic air brake knowledge can look at and instantly know how to use.
-
Product
Gas Flow Meters & Controllers
-
Accurate Mass Flow Measurement Sierra designs and manufactures a wide range of today's most advanced analog and digital gas flow meters, mass flow meters, controllers and switches across three core technologies: Capillary Thermal, Immersible Thermal, and Mass Vortex. Each gas flowmeter or controller meets exacting standards, and we can also customize your flow rate sensor to meet application requirements (often free of charge).
-
Product
HS1760/MIL-STD-1760E Network Interface Controller for PCI Express
PCIe-1760-NIC-FP
-
Avionics Interface Technologies
Configuration Variants available: PCIe-HS1760-NCNT: One NC Node and One NT Node, PCIe-HS1760-NCNC: Two NC Nodes, PCIe-HS1760-NTNT: Two NT Nodes - SAE AS5653-Compliant Network Controller/Network Terminal NIC - Unsolicited data path for handling Fibre Channel link service or non‐FC-AE‐1553 traffic - Supports DMA for high speed streaming of data - 75 Ohm single‐ended or 150 Ohm Differential coax interface – TNC connectors - Each port supports 1.0625 Gbps speed - ANSI C API interface for both NC and NT - Device driver support: Windows, Linux, & VxWorks - Quad (4) port board available on request
-
Product
PathWave BenchVue Advanced Power Control And Analysis For Multiple Instrument Connections
BV9200B
-
Control and analyze voltage and current measurements from multiple N6705C, N7900 or RP7900 Series
-
Product
CompactPCI
3U PMC Carrier
-
This conduction cooled 3U CompactPCI single slot PMC provides an active interface between the CompactPCI bus (backplane) and a PCI Mezzanine Card (PMC). This product addresses the needs of aerospace, military, and rugged applications. It contains a thermal heat frame made of aluminum that fits together with conduction cooled PMC modules. Conduction cooling conducts heat away from the hot spots of the board and transfers the heat to the card edges and to the system chassis. No active ventilation is necessary inside of the system, which means the boards are sealed from the environmental influences found outside of the chassis. The heat frame and integrated wedge locks for the conduction cooling stiffens carrier and PMC module enabling the board to resist high shock and vibration.
-
Product
Intelligent Pressure Display Controller
HR5310/HR5311
-
HighReach Measuring & Controlling System Co.,Ltd
HR5310 intelligent pressure display controller is an intelligent pressure measurement and control product that integrates pressure measurement, display, output and control, with RS485 digital interface; the product is a fully electronic structure, using international brand pressure sensors, high-precision A/D conversion, microprocessor operation processing, on-site display, and output of one analog quantity and five switch quantities.The intelligent digital pressure controller is flexible to use, simple to operate, easy to debug, safe and reliable, and is widely used in hydropower, tap water, petroleum, chemical, machinery, hydraulic and other industries to measure, display and control the pressure of fluid media.
-
Product
M1 Control
-
Provides uncompromising security and life safety on site, plus secure connectivity with popular smart devices!
-
Product
Reach-In Temperature and Humidity Control Chamber
-
The High Low Humidity and Temperature Test Chamber from Weiber are specially designed equipments that are used for testing a wide variety of products for their performance under alternating hot and cold temperature and humidity conditions. These test chambers are most commonly employed for the testing of electronic items, electrical devices and equipments, aviation products and other materials and find widespread usage in aerospace industries, electronics industry and scientific organizations involved in material research and development. These climatic test chambers use advanced technologies for highly reliable and accurate test results and are designed for energy efficient, economical and long lasting performance.
-
Product
Analog Controller Meters
-
Accuracy 0.05% F.S.±1digit Measuring six channel DCA/DCV/Pt-100/Thermocouple/etc... Programmable rate -1999 to 9999 digit Input channel number(1~6) can be modified Digit RS-485 interface function (optional) CE EMC certification
-
Product
Process Control Instruments
-
Sensors to measure process conditions and valves to influence process operations are essential for all aspects of engineering practice. Engineers want to design and operate processes that remain in safe conditions, produce the desired amounts of high quality products and are profitable. Therefore, engineers must provide measuring devices for key variables and valves (or other devices, such as variable speed electric motors) to influence of “steer” the process. This site provides educational material on sensors and valves for use in the process industries.
-
Product
Controllers
-
*Inputs for analog, digital, diagnostic and pulse signals*Digital, PWM or current-controlled outputs*Programmable to IEC 61131-3 with CODESYS*High-performance CAN interface for various communication tasks*E1 type approval (German Federal Motor Transport Authority)
-
Product
Miniature Pressure Controller
VSO®-EP
-
Parker’s VSO- Electronic pressure control unit is specifically designed for precision gas and microfluidic flow control
-
Product
Bridging And I/O Expansion Versatility. Rapid Hardware Acceleration For Improved Signal Control.
MachXO2
-
*Up to 256 kbits of user Flash memory and up to 240 kbits sysMEM™ embedded block RAM*Up to 334 hot-socketable IOs that avoid excess leakage*Programmable through JTAG, SPI, I2C or Wishbone*TransFR feature allows in-field design update without interrupting equipment operation*Programmable sysIO™ buffer supports LVCMOS, LVTTL, PCI, LVDS, BLVDS, MLVDS, RSDS, LVPECL, SSTL, HSTL and more
-
Product
Motion Control Terminal Board For Panasonic MINAS A4 Servo Amplifiers
DIN-814-A40
Terminal Board
- Panasonic MINAS A4 super servo- Dimensions: 123 mm x 107 mm x 44 mm (WxLxH)- Available for PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134
-
Product
Measuring system for GIS Remote Control Digital Recorder
VFT
-
The VFT-Measuring System TR-AS RC for VFT is special designed for high bandwitdth and allows measurements of very fast transients (VTF) in a frequency range from power frequency up to 100MHz directly with help of capacitive sensor, e.g PD-Sensors Installed in GAS-insulated Switchgear (GIS)
