Generators
Generation of electrical, mechanical, data, electrical, vapor or gas states.
See Also: Waveform Generators, Frequency Generators, RF Generators
-
Product
LGA1700 12th/13th/14th Generation Intel® Core™ I9/i7/i5/i3 ATX Motherboard With DP/HDMI/VGA, DDR4, USB 3.2, M.2
AIMB-788
Motherboard
Intel® 12th/13th/14th generation Core™ i9/i7/i5/i3 & Pentium®/Celeron® processor with Q670E chipsetFour DIMM sockets up to 128 GB DDR4 3200Triple display DP/HDMI/VGA and dual GbE LANM.2, SATA RAID 0, 1, 5, 10, USB 3.2 Gen 2Advantech iBMC remote out-of-band power management solution on DeviceOnAWS (Amazon Web Service) IoT Greengrass qualifiedNote 1: Legacy platform is not supportedNote 2: dTPM 2.0 module is required to enable Intel vPro and TPM technologiesNote 3: Intel® Platform Trust Technology (Intel® PTT) ready for Windows 11
-
Product
High-Frequency Amplifiers
-
Tabor’s line of High-Frequency Amplifiers allows for a better, more advanced utilization of the already available digital outputs on some of Tabor’s arbitrary waveform generators.
-
Product
High Current / High Voltage Pulsers
DEI Division
-
Berkeley Nucleonics Corporation
is optimized for high impedance capacitive loads, driving extraction grids and deflection plates, and pulsing or gating power tube grids. It generates an output voltage of 6,000 volts with rise and fall times less than 60ns, with very flat voltage pulses from 160 nanoseconds to DC into a capacitive load.
-
Product
Ethernet/LXI generatorNETBOX 16 Bit Arbitrary Waveform Generator - up to 40 MS/s on 4 Channels
DN2.653-04
Arbitrary Waveform Generator
The generatorNETBOX DN2.65x arbitrary waveform generators (AWG) is a general purpose multi-channel AWG with outstanding dynamic performance. The series includes LXI units with either four, eight or 16 synchronous channels. The large onboard memory can be segmented to replay different waveform sequences.
-
Product
Accelerometer (Charge Output Type)
NP-2000 Series
-
This sensor converts mechanical vibrations into electric signals in proportion of vibration acceleration.You can choose the one that is ideal for your purpose,conditions,applications etc. from wide variety of selection.Charge amplifier is necessary because it is a charge output type,however, compared to pre-amplifier built-in type, it can be used at higher temperature in general.
-
Product
PXIe-6545, 200 MHz, 32-Channel PXI Digital Waveform Instrument
780993-02
Digital Waveform
200 MHz, 32-Channel PXI Digital Waveform Instrument—The PXIe‑6545 is a digital waveform generator and analyzer for interfacing with 32 single-ended digital pins. The device is capable of sampling digital waveforms at up to 200 MHz and interfacing with common transistor‑to‑transistor logic (TTL) voltage levels. The PXI‑6545 also features advanced synchronization capabilities for building integrated mixed-signal test systems and per-bank digital timing features.
-
Product
HD Color Bar Generator
CBG830
-
The CBG830 color bar and test signal generators will produce a quality, high definition full field color bar signal compatible with the digital HDMI and DVI-D interfaces. The CBG830 is designed to provide an accurate and affordable signal source for easy testing of displays, cables and systems.The CBG830 will generate a full field color bar signal with eight vertical bars, white through black. This signal is available in a variety of resolutions and refresh rates. TheCBG830 will usually fit in a toolbox with ease and even fit into a pocket. There is also a rack mount kit available as well. Power is provided by a regulated 5VDC source and a small wall plug power module is included with the packaged CBG830 but not with board level products. The CBG830 will have a switch array to select the video standard.
-
Product
Intel® Core™ I Automation Computer With 2 PCI(E) Expansion Slots
UNO-3283G
-
6th Generation IntelR Quad Core Processors with 8GB DDR4 Memory2 x GbE, 6 x USB 3.0, 2 x RS-232/422/485, 2 x RS-232 (pin header), 1 x DVI-I, 1 x HDMI1 x PCIex16, 1x PCI, 2 x mPCIe (2 x full), 1x CFast slot, 1 x mSATA slot (optional)Thumb screw for easy maintenanceHot-Swappable HDD/SSD support for RAID 0/1Easily exchangeable RTC batterySupports Fieldbus Protocol by iDoor TechnologyChassis Grounding ProtectionLAN Redundancy (Teaming)
-
Product
Software
IRMS
-
Elementar Analysensysteme GmbH
The most advanced software ever created for the stable isotope community, the IonOS® has been designed uniquely for stable isotope analysis and aims to save analysts time and money while at the same time facilitating consistent data generation. It provides exceptional automation and sophistication for GC and EA data processing. ArDB analytics software extends the envelope of data analysis beyond simply data processing. Perhaps more so than any other analytical technique, stable isotope ratio mass spectrometry is about comparison. Comparisons of one stable isotope to another; comparisons of a sample to a standard, and comparison of unknown samples to known samples within a database. With ArDB, we provide powerful new stable isotope data analytics tools.
-
Product
COM Express® Basic Size Type 6 Module with Hexacore Mobile 9th Gen Intel® Xeon®, Core™, Pentium® and Celeron® Processors
Express-CFR
Computer on Module
The Express-CFR is COM Express® COM.0 R3.0 Basic Size Type 6 module supporting the Hexa-core (6 cores) 64-bit 9th Generation Intel® Core™ and Xeon® processor (codename “Coffeelake Refresh-H”) with Mobile Intel® QM370, HM370, CM246 Chipset.
-
Product
Battery Data Logger
BDL-3927
-
Kongter Test & Measurement Co., Limited
BDL-3927 is updated Battery Data Logger to meet IEEE measurement standards for battery voltage, string voltage, current and ambient temperature. It is customized from 12V to 700V for different battery systems. And it has easy expansion for all battery systems. With wifi communication, you could easily view complete data and generate test report in the PC software.
-
Product
EXG X-Series RF Vector Signal Generator, 9 kHz to 6 GHz
N5172B
Vector Signal Generator
Achieve faster throughput and greater uptime with cost-effective performance optimized for manufacturing testPerform basic parametric testing of components and functional verification of receivers with industry-leading ACPR, EVM, and output powerReduce the time you spend on signal creation with Signal Studio software; purchase only the waveforms you need with 5- and 50-pack licensingMinimize downtime and expenses with self-maintenance solutions and low-cost repairs
-
Product
3U CPCI Multifunction I/O Board
75G5
Multifunction I/O
NAI's latest generation 3U cPCI Multifunction I/O and Communication Board, the 75G5, can be configured with up to three smart function modules. Ideally suited for rugged military, industrial, and commercial applications, this low-power/high-performance board delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems.
-
Product
Wind-Solar Hybrid Generator
-
FD-200W (300W) Small wind turbines suitable for wind resource is better to ensure electricity inconvenience areas or occasions, especially combined into scenery complementary power supply system, may be partially or completely replace electricity to meet its rated Output power range of all kinds of electrical power requirements. Small size, light weight, low wind speed Cut the use of maintenance-free, high reliability and easy to install set up, working and long life and so on.
-
Product
Antenna, Omni-Directional Wideband Discone
EM-6105 | 10 KHz – 2 GHz
-
The EM-6105 is a broad band collinear array allowing very wide Omni-Directional frequency coverage in a single package. Below approximately 100 MHz, the EM-6105 acts as an active vertical rod which offers 10 to 12 dB more signal handling capability than competitive antennas (overload field strength: 2 V/meter) which greatly reduces intermodulation generated signals in a typical read world RF environment. In the congested spectrum above 100 MHz the antenna is passive and contributes no intermodulation products so the overload point is determined solely by the receiving instrument. This immunity to overload can often make the difference between useful signal output and an indecipherable jumble of spurious products and is accomplished without compromising sensitivity. The antenna collapses for convenient storage and transport. The EM-6105 is supplied with an EM-6106 Battery Pack.
-
Product
Pulse Adapter
CV30 P300
-
Frothingham Electronics Corporation
The CV30 P300 test station is the highest current 30KW pulser in a series of exponential pulse generators that can be connected to our FEC200E tester. This gives you all the versatility of the proven FEC200 with the addition of high power exponential pulses. For exponential pulses up to the 10/1000, the station can produce 30KW, 1000A, or 300V whichever is the most limiting. The station can also include all of the usual FEC200 tests in the same test program.
-
Product
PCI / PMC / CompactPCI Test System
PCITS
-
The CPCI850 analyzer provides a multitude of functions to help you analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation- Target memory with addressable windows- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics- Compliance testing
-
Product
Modulator
SFT3306I
-
Hangzhou Softel Optic Co., Ltd.
SFT3306I 6in1/16in1 ISDB-T modulator is the latest generational Mux-modulating device developed by SOFTEL. It has 6 (or16) multiplexing channels and ISDB-T modulating channels, and supports maximum 192 (or 512) IP input through the 3 GE ports and 6 (or16) ISDB-T non-adjacent carriers (50MHz~960MHz) output through the RF output interface. The device is also characterized with high integrated level, high performance and low cost. This is very adaptable to newly generation DTV broadcasting system.
-
Product
Leeb Hardness Testers
-
Your product description goes here. Leeb hardness tester application: Leeb hardness tester is for metal. Die cavity of molds,Inspection of bearing and other mass produced parts on a production line,Failure analysis of pressure vessel, steam generator and other equipment, Inspection of installed machinery, permanent parts of assembled systems and heavy work pieces.Rapid testing in large range and multi-measuring areas for large-scale work piece.
-
Product
GPIB Interface Card
PI-31000
-
The Pulse Instruments PI-31000 IEEE Interface Card is a standard GPIB Interface card offered by National Instruments. This interface card is used in applications where the PI-2005 Pattern Generator or other instruments are controlled from a remote system CPU, or it can be used as the system controller when the CompactPCI CPU is the system computer.
-
Product
Impulse Current Generator
-
Weshine Electric Manufacturing Co., Ltd
Impulse current generator is mainly used to test the ability of electrical equipment to withstand strong impulse current, widely used in lightning arresters and electrical and electronic equipment in operation conditions of oscillation wave immunity test, can also be used for other research tests.
-
Product
24-Bit High-Resolution Dynamic Signal Acquisition and Generation Module
PCI-9527L
Signal Module
The PCI-9527L is a high-performance, 2-CH analog input and 2-CH analog output dynamic signal acquisition board. This board is specifically designed for audio testing, acoustic measurement, and vibration analysis applications.The ADLINK PCI-9527L features two 24-bit simultaneous sampling analog input channels. The 24-bit sigma-delta ADC provides a sampling rate up to 216 KS/s at high resolutions, making it ideal for higher bandwidth dynamic signal measurements. The sampling rate can be adjusted by setting the onboard DDS clock source to an appropriate frequency. All channels are sampled simultaneously and accept an input range from ±40 V to ±0.316 V. The PCI-9527L analog input supports software selectable AC or DC coupling and 4 mA bias current for integrated electronic piezoelectric (IEPE) sensors.
-
Product
Remote Plasma Source
MAXstream
-
Advanced Energy’s MAXstreamTM line is the next generation of remote plasma sources for chamber cleaning. The MAXstream is available in 3, 6, 8, 10, and 12 SLPM NF3 flow rates to optimize price and performance.
-
Product
StarLine Spectrometers
-
The AvaSpec StarLine series of instruments is comprised of high-performance spectrometers that exceed the demands of most general spectroscopy applications. This instrument line offers a wide array of solutions for various uses while providing excellent price-to-performance ratios.
-
Product
Spectrum Analyzers
-
A refurbished spectrum analyzer is the best solution if you are looking to stretch your budget. The spectrum analyser is typically a more expensive piece of test equipment when compared to other general purpose test instrumentation. Depending on your test needs and budget a new spectrum analyzer may be the preferred choice. We have a very wide selection for you to choose from and a product for every budget.A spectrum analyzer is found in three basic forms, bench top, handheld, and portable. The spectrum analyser enjoys a long useful life and good resale value because of its fundamental use, the measurement of the spectrum of a signal. Microprocessor speeds change but frequencies do not. Basic and real time signal and spectrum analysis is always a test need especially now given the wireless world we live in. As wireless consumer and industrial devices continue to come on the the market, the spectrum analyzer can be found in more and more design, in house test, manufacturing, quality, field test, and remote repair applications.Test Equipment Connection offers Spectrum Analyzers in a various range of prices and categories, allowing you to find the equipment you need. Search by Frequency, number of channels, brand or price range. Test Equipment Connection has made it easy to find the equipment that is right for you.
-
Product
Hand Multiplexers
MTM
-
The manual torque multiplier is a low cost solution that's ideal for wheel nuts and remote locations where air and electricity aren’t easily accessible. The gearing design allows for a high torque output with minimal input. Commonly used in petrochemical, power generation, transportation, shipping and maintenance industries.
-
Product
100W Dual Output Power Supply Two 8V, 5A or 20V, 2.5A
E3648A
Power Supply
Keysight basic DC power supplies offer essential features for a tight budget. The single & dual output, 30-100 W GPIB E3640 series provide small, compact size for bench and system use; low output ripple and noise; and built-in measurements and basic programmable features with GPIB and RS232 interface. The Keysight 90W, multiple output E3648A is a clean, reliable power supply for general purpose applications, and combine convenient benchtop capabilities with flexible system features in a compact, multi-output package.
-
Product
SWB-2817, 16x22, 0.3 A, Reed Matrix Module for SwitchBlock
781420-17
Relay Matrix Module
16x22, 0.3 A, Reed Matrix Module for SwitchBlock - The SWB‑2817 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
General Purpose Benchtop XRD System for Phase I.D. and Phase Quantification
-
In a move to bring lab-quality performance to the manufacturing floor, Rigaku introduces the MiniFlex XpC, a manufacturing-optimized powder diffractometer for fast and accurate quality control measurements. It is extremely easy to operate using Rigaku’s new EasyX quality control software, which requires minimal clicks to run. A minimal interface means there will be no accidental error variance from operator to operator. The MiniFlex XpC can be configured with a conveyor belt or robot for automated sample processing and collaboration with other instruments. With an 800 W X-ray source and a short-diameter goniometer, the system has the performance of a lab unit, and thus can greatly improve throughput for quality control measurements.
-
Product
RTM Analog Signal Conditioning Board
MS 3633I
-
CPCI Rear IO Analog Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advanced Compute & IO Module (MS3639i). This board primarily focusing on all type of Analog input and output interface including signal conditioning from ACIO board to Rear IO interface. Board takes 16 Analog outputs and 64 Analog inputs from ACIO and does signal conditioning. In addition it shall generate additional 40 Analog input and 32 Analog output signals with signal conditioning and all IO interfaces are brought to two 96 Pin Euro Connector.
