Generators
Generation of electrical, mechanical, data, electrical, vapor or gas states.
See Also: Waveform Generators, Frequency Generators, RF Generators
-
Product
Optical Modulator
-
Is an Intensity Modulator that is manufactured with Annealed Proton Exchange(APE) process, it features a zero-chirp design and Polarization Maintaining(PM) fiber output. Features 20 GHz E/O bandwidth, a highly linear transfer function and excellent extinction ratio. Applications include digital transmission up to 20 Gb/s, analog RFoF transmission to 20 GHz, optical pulse generation, mode-locked fiber laser and microwave optical link.
-
Product
Mini Array+
DORC's ZX-1
-
Direct Optical Research Company
Used primarily to measure multi fiber (MT/MPO and MT-RJ) connectors, DORC's fourth generation "ZX-1 mini Array+" is the result of 18 years of hardware and software product development. Although optimized for mutifiber connectors, the ZX-1 mini Array plus also does an excellent job of measuring single fiber PC and APC connectors. DORC's patented design is based on a variant of the Michelson configuration, and provides BOTH 2D and 3D high resolution images of the sample under test in approximately 45 seconds for multi fiber connectors and just 3-4 seconds for single fiber connectors - from the time the connector is inserted.
-
Product
Standard 1.50 (43.00) - 3.00 (85.00) General Purpose Probe
P2665G-2W1S
General Purpose Probe
Current Rating (Amps): 15Average DC Resistance lower than (mOhm): 10Test Center (mil): 125Test Center (mm): 3.18Full Travel (mil): 230Full Travel (mm): 5.84Recommended Travel (mil): 167Recommended Travel (mm): 4.24Overall Length (mil): 1,290Overall Length (mm): 32.77Overall Length Remark: Tip 2W: 1270 mil (32.26 mm)
-
Product
Environmental Noise Monitors
-
Noise is one of the most complained about aspects of the environment, as not only does it have the potential to affect quality of life, it can also be difficult to monitor and therefore control. This type of noise is generally called environmental noise. There are many man-made sources of environmental noise, such as wind turbines, industrial sites, roads and traffic etc. If you are looking for equipment to measure noise in the workplace, look at sound level meters.
-
Product
Alternate 3.00 (85.00) - 5.70 (162.00) General Purpose Probe
P2664G-1C2S
General Purpose Probe
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 10Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 114Full Travel (mm): 2.90Recommended Travel (mil): 84Recommended Travel (mm): 2.13Overall Length (mil): 895Overall Length (mm): 22.73Overall Length Remark: Tip 1C: 845 mil (21.46 mm) Tip 2R: 935 mil (23.75 mm)
-
Product
Thick Film Passive Element
GBR-182
-
GBR-182 series resistors are made in a thick film technology, on ceramic substrates (Al2O3 - 96%). Thick film resistors are characterized by a higher stability, and lower noises than a typical carbon resistors. The whole of resistor is encapsulated with epoxy resin by fluidization process. GBR-182 series elements are used both for general, and professional applications.
-
Product
Digital Signal Processor Card
CHAMP-AV8
-
Curtiss-Wright Defense Solutions
The CHAMP-AV8 6U OpenVPX digital signal processor (DSP) combines the floating-point performance of the 3rd generation Intel Core i7 processors with the substantial bandwidth and system-enabling features of the 6U OpenVPX form factor. Utilizing a pair of 2.1 GHz quad-core processors featuring the Advanced Vector Extensions (AVX) instruction set, the CHAMP-AV8 DSP card delivers up to 269 GFLOPs.
-
Product
AC Load Bank (Resistive)
K-1000 Resisitive
-
Kongter Test & Measurement Co., Limited
The kW of a resistive load bank is “real” power in electrical terms. When a resistive AC load bank is used to test an engine generator set the engine will produce its full horsepower rating, dissipate engine exhaust gases, and produce thermal energy into the engine cooling system. The resistive load bank in fact, will completely test the engine and its various systems.
-
Product
Digital Radiography Software
SHERLOCK NDT
-
Sherlock NDT is the perfect link between Teledyne ICM best in class portable X-ray generator, the CPSERIES, and our high-resolution digital radiography detectors, the Go-Scan SERIES. Developed by and with NDT DR specialists, this intuitive and user-friendly touchscreen software produces high-quality images, allows real-time (video) acquisition, and comes with many different enhancement features.
-
Product
Cavium CN66xx Packet Processor AMC
AMC732
-
The AMC732 is a 10-Gigabit Ethernet (10GbE) AdvancedMC™ (AMC) module which includes an on-board multi-core packet processor based on Cavium CN66XX CPU. VadaTech offers this product in a mid size (full size optional) form factor with the AMC.1, AMC.2 and AMC.4 specification. The AMC732 is based around the Cavium OCTEON CN66xx processor which has been specifically designed to intelligently process Ethernet packets at line rate. The processor can be loaded via the PCIe/SRIO interface or via an optional flash memory. The number of processor cores, speed grade, and amount of DDR3 memory is customizable based on customer needs.The module has an RTC on board and 2GB of HFA for pattern matching for deep packet inspection, etc. The SDK for the processor as well as additional software stacks are available from Cavium or third party. The AMC732 has Serial Over LAN (SOL) with a true hardware Random Number Generator.
-
Product
Standard 1.68 (48.00) - 3.20 (91.00) General Purpose Probe
HPA-52T
General Purpose Probe
Current Rating (Amps): 3Average Probe Resistance (mOhm): 15Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 75Full Travel (mm): 1.91Recommended Travel (mil): 75Recommended Travel (mm): 1.91Mechanical Life (no of cyles): 250,000Overall Length (mil): 629Overall Length (mm): 15.98
-
Product
Frequency Converter Unit
FCU
-
The Astronics Frequency Converter Unit (FCU) provides frequency conversion of variable frequency aircraft power. Recent trends in aircraft power systems use variable frequency (VF) generators instead of fixed frequency of 400Hz. While the majority of aircraft loads can use VF power, select loads still exclusively require 400Hz and are best addressed by the use of FCUs. The FCU performs the task of converting the power line frequency by leveraging recent advances in solid-state technology to provide dramatic improvements in performance over traditional frequency converter solutions.
-
Product
PXI Function Generator
Function Generator
Our PXI Function Generator is capable of generating sine, square and triangle waveforms to 10MHz with 48-bit frequency resolution referenced to the 10MHz PXI clock or to an external standard. It can generate fast swept frequency signals, permitting the output to emulate the operation of variable speed devices. The module can also generate arbitrary waveforms loaded into its internal 256k memory, allowing the emulation of many waveform types including the typical waveforms of automotive and aerospace sensors.
-
Product
Mixed Signal Oscilloscope - 100 MHz, 4 Analog Plus 16 Digital Channels
MSOX3014T
Oscilloscope
100 MHz4 analog plus 16 digital channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
Product
Special / Customer Spec. Crates
6U VME64x 4500
-
The WIENER VME 4500 crate series is a compact new generation of 19" integrated packaging system with frontal cooling air intake for standard VME64x bus systems with 6Ux160mm cards. Designed primarily for applications in data acquisition, control and test instrumentation it combines superior mechanical quality with lowest noise power supply technology.
-
Product
Transient Immunity Tester
KES7700
-
Transient Immunity Tester KES7700 Series are transient surge tester that utilizes a compact unit system. A surge generator circuit is installed for each pulse unit as the tester meets the requirement of ISO7637-2, ISO7637-3, ISO16750-2, JASO D001, SAEJ1113, and other standards. The KES7700 Series meets a broad range of independent automobile manufacturer standards as well.
-
Product
Partial Discharge Measurement Calibrator
DAC-CP-2
-
DAC-CP-2 is a calibrator for partial discharge measurements.The electric charge enables to generate up to max 10000pC.It is battery-operated and can be charged by connecting to the measuring instrument (DAC-PD-3).
-
Product
Serial Controller
PMC522/FP
Controller
The PMC522/FP provides a uniquely effective solution for integrating serial I/O requirements into a VMEbus or CompactPCI system. Implemented on a single PMC card, the PMC522/FP is fully compatible with the current generation of VMEbus and CPCI single board computers, as well as any special purpose processor that includes a PMC connector.
-
Product
Speaker/Receiver Unit Test Generator
BK2019
-
The BK2019 Generator is easy to operate, simple to set up, and you can fit it just about anywhere. This portable generator produces tones or sweeps and is technology you can whip out of your briefcase, plunk down on a table and start using. It's equally useful for either spot checking or for quality control. The setup is so easy that you can change DUT's in minutes.
-
Product
*PCIe-5785, 12-Bit, 6.4 GS/s, 2-Channel FlexRIO IF Transceiver Device
785587-02
FlexRIO IF Transceiver
The PCIe-5785 enables direct RF acquisition up to 6 GHz and generation up to 3 GHz with 12 bits of resolution. You can use it in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The PCIe-5785 is ideal for applications that require wideband acquisition and generation with multichannel synchronization, including radar, electronic warfare, and communications. The FlexRIO driver includes support for acquiring and generating waveforms out of the box, and you can use the LabVIEW-programmable Xilinx Kintex UltraScale FPGA to implement custom algorithms for real-time signal processing.
-
Product
(250 kN) Fatigue Testing System
8802
-
The Instron 8802 is a high stiffness, 250kN fatigue rated servohydraulic testing system that meets the challenging demands of both static and dynamic testing requirments. The 8802 systems include a range of configurations available to provide complete testing solutions to satisfy the needs of advanced materials and component testing. The design of the 8802 frame makes it ideal for installation within a laboratory environment, generally without the need for strangethened floors or raised ceiling heights.
-
Product
Positional Current Probe, PCB Track Touch And Measure
I-prober 520
-
Current measurement from insulated probing of conductorSuitable for observation and measurement of current in PCB tracks, component leads and ground planesWide dynamic range of 10mA to 20A peak to peakWide bandwidth of DC to 5MHzLow noise figure equivalent to <6mA rms at full B/WSafety rated to 300V Cat II (600V Cat 1)Suitable for connection to any oscilloscopeHigh accuracy general purpose H-field probeConverts to 'closed magnetic circuit' current probe
-
Product
Electrostatic Discharge Simulator
ESD61000-2
-
ESD simulator (Electrostatic Discharge Generator or Electrostatic Gun) is in full compliance with IEC 61000-4-2, EN61000-4-2, ISO10605, GB/T17626.2, GB/T17215.301 and GB/T17215.322. The ESD generator is designed for the assessment of electrical and electronic equipment to withstand ESD performance. ESD61000-2/ESD61000-2A has LCD display in both English and Chinese, they equipped with an infrared remote control which can allow you do the test in some special place.
-
Product
Intel® Atom™ Processor E3845 Fanless Expandable Embedded Computer with PCI/PCIe Slots
MXC-2300
Industrial Computer
Featuring the latest Intel® Atom™ E3845 processor, the Matrix MXC-2300 series excels with minimal power consumption, exceptional 3D graphics, and powerful media acceleration, delivering a leading improvement in performance and cost-efficiency over any previous generation Atom-based system.
-
Product
SWB-2814, 8x9, 1 A, 2-Wire Reed Matrix Module for SwitchBlock
781421-14
Matrix Switch Module
8x9, 1 A, 2-Wire Reed Matrix Module for SwitchBlock - The SWB‑2814 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
PXI/PXIe MEMS Optical Switch, Dual Insert/Bypass
40-860A-422
Multiplexer Module
The 40/42-860A-422 is a PXI/PXIe dual insert/bypass switch with LC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
PXIe Multi-Channel Function Generator Module, 8-Channel
43-625-004
Function Generator
The 41-625-004 (PXI) and 43-625-004 (PXIe) are function generator modules that provide 8 channels in a single PXI/PXIe slot. They can generate sine waves to 300 kHz with 5.76 mHz frequency resolution referenced to the 10 MHz PXI clock. The output voltage range is up to +/-25 V in a 16-bit resolution. It also support PXI trigger functions allowing events from other instruments to initiate waveform generation or sweeps.
-
Product
Pulse Generators
Split Collar Pulser Wraps
-
Pulser wraps clamp around a rotating shaft and work with Electro-Sensors shaft speed sensors and are an ideal solution for installations where the end of the shaft is inaccessible. The two halves fasten together around the monitored shaft with recessed Allen head socket screws (provided). Standard and custom models accommodate any shaft diameter, tight spaces, and keyways.• Standard wraps operate to 3,000 rpm (high-speed also available)• Standard wraps available in PVC, aluminum, or stainless steel
-
Product
Arbitrary Waveform Generators
M8100 Series
-
The M8100 Series arbitrary waveform generators (AWGs) offer a level of versatility that enables you to set up complex real-world signals — whether you need precise signals to characterize the performance of a design or need to stress a device to its limits. From low-observable radar to high-density communications, testing is more realistic with our precision arbitrary waveform generators.
-
Product
Calibration Kit
FMCK1000
-
Designed to withstand daily use in high-traffic environments such as in the testing lab or on the production floor. This cost effective calibration kit provides reliable and accurate instrument tuning for all of your test and measurement requirements. Applications: VNA, Full 2-Port CAL VNA, Thru CAL VNA, Substitution CAL method Test & Measurement Lab Equipment Accessories Engineering Test and Evaluation General Purpose Test and evaluation.
