Standards
A controlled reference or acknowledged technical criterion.
See Also: IEC, IEEE, Mil, Interoperability Test, Compliance
-
product
Portable Connector End Face Geometry Interferometer
Thorlabs’ Vytran® Connect-Chek® Interferometer automatically and precisely measures radius of curvature, apex offset of polish, and fiber undercut or protrusion on any PC or APC, single-fiber connector. The CC6000 interferometer uses a non-contact tilted-phase-analysis technique for fast, reliable measurements of connector end faces. This compact interferometer has a carrying handle and must be attached to a desktop or laptop computer (not included) with a standard USB 2.0 port for operation. The included CC6000 software, which is used to control the interferometer, can be installed on a computer with the minimum requirements in the table below. Designed for use in both the factory and the field, this interferometer provides crucial quality information needed to assure long-term performance of fiber optic connectors. One CC250P Mount for Ø2.50 mm PC Connectors and one RT250P Reference Tool for calibrating the CC250P mount are included with the CC6000 interferometer; mounts and reference tools that enable measurement of other PC or APC, single-fiber connectors are available separately below. When used with an appropriate mount for APC connectors, the CC6000 interferometer is also capable of measuring the APC angle and key error.
-
product
2-Way Power Dividers From 0.23 To 70 GHz
Pulsar Microwave manufactures a large selection of 2-way power dividers in narrowband and broadband configurations, covering frequencies from 225 MHz to 70 GHz. They are designed to handle from 10 to 30 watts input power in a 50-ohm transmission system. Microstrip or stripline designs are utilized, and optimized for best performance.Units come standard with SMA or N female connectors, or 2.92mm, 2.40mm, and 1.85mm connectors for high frequency components.
-
product
Mass Flow Controller for Medium Flow
HFM-205 / HFC-207
The HFM-205/HFC-207, Teledyne Hastings' flexible, general purpose series of mass flow meters and controllers accurately measure and control mass flow in a variety of applications. Featuring reliability and stability, the 200 Series is chosen for its very stable performance with varying ambient conditions. A wide choice of elastomer seals make this flow controller compatible with most gases.The HFM-205 / HFC-207 meters and controllers have flow ranges from 0-1000 slm to flows of 0-2500 slm; provide analog outputs, are constructed of stainless steel and can be configured with normally open or normally closed valves. The full scale range is specified by the end user. A NIST traceable calibration certificate is standard. With a full complement of fitting and elastomer options, the HFM-205/ HFC-207 covers a wide range of high flow applications.
-
product
Low Pressure Drop Thermal Mass Flow Meter
HFM-200 LFE
The HFM-200 LFE Series by Teledyne Hastings can be configured and accurately measure gas flow in a broad array of applications. Featuring reliability and stability, the 200 Series is chosen by users for its very stable performance with varying ambient conditions. A wide choice of elastomer seals make this flow meter compatible with most gases.The HFM-200 LFE meter has flow ranges from 0-10 sccm to flows of 0-15,000 slm; provides analog outputs, and is constructed of stainless steel. The full scale range is specified by the end user. A NIST traceable calibration certificate is standard. Cleaning for oxygen service is available. Our laminar flow elements (smooth, threaded or flanged) are available in various sizes from 3/8" up to 8". Low pressure drops at full scale flow.
-
product
DC Source/Calibrators
Our DC Source/Calibrators are designed for a typical applications such as the design, check and calibration of high speed, high resolution A/D converters; design and certification of high speed data logging and process control systems; calibration of digital voltmeters and multimeters; as an “IMBEDDED STANDARD” and/or simulator; design, testing, simulation and certification of thermocouples, strain gages and transducer instrumentation.
-
product
PXI 16-Channel USB Data Comms MUX
40-737-001
The 40-737-001 is a 16:1 USB data communications multiplexer suitable for switching USB1 and USB2 data and power connections using a 78 way D-Type connector. The data signal paths are 2-pole arranged as differential pairs as defined by the USB standard.
-
product
IEC61588 And IEC60065 Mandrel Test Apparatus
CX-M01
Shenzhen Chuangxin Instruments Co., Ltd.
IEC61588 and IEC60065 Mandrel Test Apparatus is designed and manufactured in accordance with the standard requirements of IEC61558 and IEC60065. The IEC61588 and IEC60065 Mandrel Test Apparatus is used for the insulating thin layer of the power transformer and supply unit as well as the similar products to do the spindle test, mechanical strength test and abrasion test.
-
product
Exposure Systems
Model 2012AF & 2012SM
The Model 2012AF Flood Exposure System provides a cost-effective method for automated flood exposure. Designed to accommodate wafers from 8” to 300mm, the tool features automated FOUP loading. Mask and substrate changeover can be accomplished quickly and easily adding to both versatility and high-volume throughput of this production tool.The Model 2012SM Automated Edge-bead Exposure System provides a cost-effective method for edge-bead removal using standard shadow mask technology. Designed to accommodate wafers from 8” to 300mm, the tool features automated FOUP loading. Mask and substrate changeover can be accomplished quickly and easily adding to both versatility and high-volume throughput of this production tool.
-
product
Electric Servomotor Fixed Torsion Tester
This tester series is one of the fastest standardized products among electric servomotors Torsion Fatigue / Durability Tester for various materials and automobile parts .
-
product
PCIe Gen 3 ATCA Carrier With Low-Power Xeon E3
ATC123
The ATC123 is a Carrier Module with an onboard x16 PCIe Gen3 slot (only x8 PCIe is routed to the slot) to accept any standard PCIe edge type module.
-
product
VME64X 6U 5 Slot no P0
101V64XC05-0620
6U VME64x Backplane 5-slot without P0, compliant with ANSI/VITA 1.1-1997, VME extension standard. Includes termination passive inboard, daisy chain automatic active, and power bugs on top and bottom of slots.
-
product
Digital System X
DSX
We have developed this technology, not only for our customers, but for our own unique needs in the areas of prototyping and test. We found that many of the standard digital prototyping boards (FPGAs, PLDs, etc…) that are available on the market, did not have the flexibility or the base architecture to provide the prototyping capabilities we need in developing our own solutions.
-
product
Rugged PC Compatible
SYS-427X
WINSYSTEMS’ SYS-427X is a rugged, fanless industrial computer with the Intel® Apollo Lake-I SOC quad-core processor. Its compact size, low power, and extended operational temperature make it a great fit for rugged embedded systems in the industrial control, transportation, energy, and IIoT markets. In addition to the standard system configuration, three optional configurations are available, adding WiFi 6, CAN Bus, or both.
-
product
Digital Frequency Meter
CSF-400
Measuring frequency. Accuracy: +/- 0.05%. 4 Digital display: 9999 Input Max. 400Hz/600 V, 30KHz/12V. Aux. Power AC 115/230V +/-15%, 50/60Hz. Isolation Aux. Power 12Vdc, 24Vdc, 48Vdc, 110Vdc available in option. Easy-to-wire, screw type terminal. Outside dimensions is DIN standard (96mm x 48mm) High stability & low cost.
-
product
Robotic ESD Tester
SmartZap
The SmartZap is a fully automated zap gun tester with automatic failure detection capability, providing far superior performance than manual zap gun test. It is complying IEC61000-4-2 test standard.
-
product
Standard 1.60 (45.00) - 4.50 (128.00) General Purpose Probe
EPA-3A
Current Rating (Amps): 6Average Probe Resistance (mOhm): 35Test Center (mil): 125Test Center (mm): 3.18Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cyles): 2,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
product
Gauge Type T Thermocouple Wire
W-TW-44TEF
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
product
Square Wave Patterns (Ronchi Gratings/Rulings)
Square Wave patterns (Ronchi Gratings/Rulings) have extremely sharp edges. At APPLIED IMAGE, this sharpness is achieved through our unique manufacturing capabilities and processing technologies which produces the sharpest edges available anywhere. Our standard line of Ronchi Gratings is offered on Chrome on Glass (CG) and Photo Paper (RM).The Ronchi rulings are available on other substrate materials such as B270, quartz, BK-7, and White Opal as well as in English frequency metrics (cycles per inch).
-
product
PCMCIA Card
DAS-429PCMCIA/RT10
Both cards contain 68 Kbytes of true dual-port RAM, for data blocks, control registers and Look-up table, mapped within the Common Memory space. The card also contains a FLASH-based Card Information Structure (CIS) within the Attribute Memory space.The cards comply with the Personal Computer Memory Card International Association (PCMCIA Release 2.1) standard, including Plug and Play. The card's small size and suitability for PCMCIA compatible notebook computers with Type II and Type III slots make it a complete solution for developing and testing ARINC-429 interfaces and for performing system simulation of the ARINC-429 bus, both in the lab and in the field.The cards are supplied with C drivers, including source code, Mystic Windows software and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
product
Decade Box, Calibrated W/D & U, Resistance, 7, 1ohm to 11.11111Mohm, 1 %
72-7270 CAL DU
The 72-7270 CAL DU from Tenma is a resistance decade box. It is ideal for service, prototype and experimental use. This useful tool may be set resistance value from 1 to 11,111,110 ohm in one ohm increments. The decade accuracy is ±1% resistors used throughout. It has weight of 320g/0.70lb and dimension 14.7cm × 11.7cm × 5.5cm (5.79" × 4.61" × 2.16"). It is typically used in general applications, troubleshooting, maintenance, education and vocational training, production line testing, radio and TV services, working standards, research design & develop, physics laboratory work.
-
product
FC Patch Cord
FY6
Fiberyo provides a full line of fiber optic cable assemblies, covering SC, FC, ST, Din, D4, E-2000, SMA, LC, MU, MPO, MT-RJ, with PC(physical contact), UPC(Ultra physical contact), APC(Angled physical contact) polishing, using quality Fiberyo connector components, they are designed to comply with industry standards for optical, mechanical and environmental performance.
-
product
Test Programming LabVIEW
With LabVIEW, National Instruments provides an industry standard for developing a test environment.Our employees have many years of experience in many areas of this development environment.
-
product
IEC60068-2-75 Spring Hammer Calibration Device
Shenzhen Chuangxin Instruments Co., Ltd.
It is mainly used for the calibration of the spring hammer, which is based on IEC60068-2-75-1997 and GB2423.55-2006 standard design and manufacture, primarily for third-party testing organization, the National immigration department and appliance-related research institutes.
-
product
Natural Cooling Input 380VAC 3 Phase to Output 190-300VDC 10A-40A Rectifier Battery Charger
SD230D20ZZ
Zhejiang Sandi Electric Co., Ltd
SANDI “SD” series intelligent high-frequency switch power supply modules are specially developed to meet the demands of modern DC system. The charger rectifiers are designed with world leading patent technology “resonant voltage type soft switching power supply technology”. They feature high efficiency and stability, intelligent control, small size and light weight. Standard RS-485 interface, easy to connect with automation system. “Four remotes” functions, intelligent management. The products are widely used in power plant, substations and etc..
-
product
Customized Material Testing Machines
Globally growing innovations result besides fulfillment of new testing standards in an ever increasing demand for customer-specific solutions regarding the testing technologies, jigs, measuring systems, software and the automation level of the testing machines.The core competencies of TIRA are customer-specific solutions.TIRA is able to realize individual customized solutions according to customer´s request and the simplest derivations like longer, wider, narrower, shorter material testing machines.
-
product
Battery Supervisors
DV Power manufactures ideal tools for maintenance, troubleshooting and performance tests on stationary batteries.Capacity testing is performed in order to detect which cells in the string should be replaced by measuring a cell voltage, temperature, inter-cell connection voltage, and specific gravity.IEEE standards for stationary battery applications also stipulate measuring these key parameters during periodic battery inspections.DV Power provides two types of instruments:BVS series – for automated monitoring of battery parametersBVR series – for manual monitoring of battery parametersIn contrast to BVS, BVR instruments can be used for the transfer of electrolyte specific gravity measurements from a density meter (DMA35) via Bluetooth. This provides a more extensive analysis of each cell in the tested battery string.
-
product
Diaphragm Operated Pressure Switch
1000W
Extremely rugged construction provides excellent reliability in chemical, petroleum and industrial plants. Bellville spring movement permits mounting of control in any position and helps prevent contact chatter. new design also provides high overpressure protection. Available with standard weatherproof housing to meet NEMA-1 through 4X and NEMA-13, JIC.
-
product
Lightning Surge Simulators
LSS Series
A simulator to reproduce “High energy induced lightning noise” which is induced by potential change on the ground, or done to power lines or telephone lines as result of lightning current.This immunity test is required by major standards including IEC61000-4-5 and JEC 210/212 and is widely used in many industries.
-
product
Crown, Four Point, Standard 0.61 (17.00) - 2.80 (79.00) General Purpose Probe
HPA-0-Standard
Current Rating (Amps): 3Average Probe Resistance (mOhm): 35Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 100Full Travel (mm): 2.54Recommended Travel (mil): 67Recommended Travel (mm): 1.70Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 635Overall Length (mm): 16.13
-
product
Bus Analyzer / Exerciser
VME850
The VME850 Analyzer / Exerciser supports the latest VME bus specifications and protocols. From standard VME transfers to 2eSST protocol. In addition to the VME bus, user defined signals on the P0 and P2 connectors are also analyzed and exercised with optional plug-in modules.
