Isolation Amplifiers
-
Product
PXI 5A Power Multiplexer, 1-Bank, 48-Channel, Independent Isolation
40-651A-101
Multiplexer Module
The 40-651A-101 is part of our range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats.
-
Product
PXI Isolated Single Channel Voltage/Current Source, 100V
M9186A
Source Measure Unit
The V/I source lets you source a voltage and measure the resultant current, or source a current and measure the resultant voltage. It consist of two separate amplifiers, denoted "low" and "high" that share a common output connection. The "low" amplifier provides voltages in the range of 16 volts at up to 200ma and the "high" amplifier provides voltages in the range of 100V at up to 20mA.
-
Product
PXI 5A Power Multiplexer, 8-Bank, 5-Channel, Isolated Common
40-651A-014
Multiplexer Module
The 40-651A-014 is part of our range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats.
-
Product
Solid-State High Power Amplifier 18 - 26.5 GHz
AMP4065LC-2
-
Exodus Advanced Communications
Designed for EMI/RFI, lab, and general communication applications. Exodus Broadband SSPA product feature GaN, GaAsFET discrete and Chip & Wire Hybrid technologies covering one octave through decades frequency ranges from Operating Frequency Range 18.0-26.5 GHz.
-
Product
CPCI 48 Optically Isolated Outputs Card
CPCI-48OUT
Controller
The output board consists of FPGA controllers for DC output control. An FPGA provides the timing and control. Each output has its own optical isolation, and supports an open collector output. An PCI controller provides the interface to thehost computer. All I/O is accessible from the front panel.
-
Product
Broadband Amplifiers
-
R&S broadband amplifiers are innovative solid-state solutions with exceptional RF performance for generating RF power up to 13 kW in the frequency range of 4 kHz to 6 GHz. Designed as very compact amplifiers, at highest power density, they are robust against severest output mismatch while featuring high availability. Applications range from amplitude, frequency, phase, pulse to OFDM modulation.
-
Product
860MHz CATV Indoor Bi-directional Amplifier
-
Hangzhou Softel Optic Co., Ltd.
SA801H Indoor Bi-directional Amplifier are special amplifiers designed for the last”1km” of the bi-directional transmission network. Special CATV RF modules packaged in SOT-115 are used as forward channel; Microwave tube push-pull circuit with low noise are used as backward channel ;It has the characteristics of low power consumption，high reliability and excellent cost performance. And it is suitable for small and medium sized CATV bi-directional transmission network.
-
Product
Current Loop 20 MA Constant Current SI-module With Optical Isolation
MXTTY
-
Current loop 20 mA constant current (active, passive) SI-module with optical isolation.
-
Product
Portable Power Amplifier
PAV250Bip
-
PAV250Bip is the portable OPAL-RT used amplifier model, which is specially designed for R&D of power system simulation. It is designed with linear type amplifier so that it is with precise accuracy, which could be adapted to various capacitive and inductive load.
-
Product
Coaxial Isolators and Circulators
-
Smiths Interconnect's Trak brand has been manufacturing coaxial isolators at our Dundee site for over 40 years with space qualified isolator and circulators produced over the past two decades. Coaxial Isolators and Circulators are available for a wide range of applications and are designed to operate in assigned bands from 300 MHz to 31 GHz.
-
Product
Fiber Pigtailed Tapered Amplifier
-
The AOSense tapered amplifier (TA) provides a coherent high-power beam, inheriting all properties from the seed source. TA’s are an essential optical component for quantum sciences, such as laser cooling and trapping, cold atom sensors, electromagnetically induced transparency, and quantum spectroscopy. The TA is also used in commercial laser modules, including master oscillator power amplifier (MOPA) lasers and external cavity lasers.
-
Product
Broadband Power Amplifier
PAS-00210-60
-
* Solid State Power Amplifier* Gain : 50 dB typ.* High IP3, 51.0 dBm typ.* Rack Mount Case* Internal Cooling Fans* Over Temperature Protection* Output VSWR protection* Microprocessor controlled* Front Panel Information Display* RS-232 Interface* Ethernet Interface* Variable Gain* ALC power control* Type N Connectors
-
Product
Fiber Optic Sensor & Amplifier
FG-1300 | FS-5500/FS-540
-
The FG-1300 is a non-contact type high-performance amplifier that emits red light from LED to a rotating object, and detects the variation of the reflected red light amount.This amplifier is used in combination with an exclusive detector FS-5500*/FS-540 Fiber Optic Sensors which has adopted environment resistant design. The glass fibers are covered with flexible stainless steel tube for rotation measurement in limited space.
-
Product
Isolated Input Card
mPCIe-II-16
-
The mPCIe-II-16 consists of a type F1 PCI Express Mini Card (mPCIe) interface board that connects to a Mobile-ITX-sized, DB-37M Isolation Module via an included 9” cable. That module is designed to be easily panel-mounted in any application environment. It uses the high speed PCI Express bus to transfer digital data to and from the card. The digital I/O is compatible with 8255 PPI chips making it easy to program.
-
Product
Hydrophone Booster Amplifier
-
Optional enhancement to the basic hydrophone measurement system to provide further amplification of the hydrophone signal.
-
Product
2 GHz to 6 GHz, 25 W Power Amplifier Module
HMC7748
-
The HMC7748 is a multistage power amplifier (PA) that provides 25 W of saturated output power across the band of 2 GHz to 6 GHz. It draws 0.7 A from a 12 V supply and up to 4 A from a 28 V supply. Input signals of as much as −8 dBm are acceptable, and the module has small signal gain of 60 dB. The 12 V supply is regulated internally and generates the negative voltage required for the gate bias. Built-in bias sequencing prevents the drain voltages for the amplifier stages from being applied without the negative voltage present, which protects the amplifiers if 28 V is applied without 12 V supply applied.
-
Product
10RJ50-DB9M Serial Cable, 10Pos Modular Plug to DB-9, 3 m (non isolated)
182845-03
Serial Cable
S8 Serial Cable, 10Pos Modular Plug to DB-9, 3 m (non isolated)
-
Product
Single Channel High Voltage Linear Amplifier
A600
-
The A600 is a general purpose broadband linear amplifier having a fixed amplification of 100 times and capable of bipolar high voltage output of 300V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to 3 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
Product
Erbium Doped Fiber Amplifier
EDFA
-
EDFAs are based on the light amplification in erbium-doped fiber, which are optically pumped by means of 980 nm or 1480 nm light sources. In this way, the light of a larger wavelength within the C or L band applied to the input of the amplifier is amplified, thus widening the range of optical communication links. EDFAs typically operate in saturation and the average signal power determines the average gain. The dynamics of EDFA are unaffected by the sequence and dynamics of a digital signal or channel interaction in DWDM systems. As a result, multiple channels can be bundled within the total erbium spectral amplification bandwidth. However, the total average output power in both cases is determined by the saturation power of the specific EDFA.
-
Product
Transconductance & Transimpedance Amplifiers
-
Measurements International Ltd.
0 to 100 Amps – AC, 0 to ± 100 Amps – DC, Voltage Compliance ± 5 Volts, IEEE-488 Interface, Resistive, Capacitive, Inductive Loads.
-
Product
Isolated Process Control Signal Conditioning Products
SCIM7B
-
SCIM7B Isolated Process Control Signal Conditioning Modules provide a complete selection of backpanels DIN rail mounting accessories, interface cables and rack mounting hardware.Each SCIM7B module provides a single of isolated analog input or output. Various input modules accept analog voltage or current signals from all types of field sensors and sources, filter, isolateamplify, linearize and convert these input signals to high-level analog outputs suitable for use in a process control system. Output modules accept high-level analog voltage signals from a process control system, then buffer, isolate, filter, convert and amplify before providing a current or voltage output to a fielddevice.
-
Product
Amplifiers
-
Elbit Systems of America’s secure networks and communication solutions provide warfighters secured and reliable radio communications for most operational applications. Our teams work hard to deliver a number of scalable options from extremely rugged to standard industrial or commercial specifications. Our family of Single-Channel and Dual-Channel Modular Power Amplifiers operates with current and next-gen radios and offer lightweight, compact solutions on most platforms. The modular design simplifies maintenance, provides customer flexibility, and accelerates the fielding of new capabilities.
-
Product
Rack Mount Type Amplifiers
-
Amplifiers for each of O-, S-, C- and L-bands– Compatible with high-speed transmission (up to 100 Gbps)– Available for all signal types and protocols– Compatible with transmitters from all manufacturers– Compatible with SNMP
-
-
Product
Portable Oscilloscopes With Isolated Channels
-
Portable oscilloscope with 2 isolated channels, 600 V CAT III, 20 MHz bandwidth, 2 GS/s ETS, double 8,000-count multimeter with power measurements, 31-order harmonics with 40 to 450 Hz fund.,colour screen, USB.
-
Product
High Density Isolated Serial I/O Module
AMC081/081C
-
The AMC081 is a flexible serial I/O module providing 16 input and 16 output channels, all of which are individually isolated. I/O transceivers meet or exceed the requirements of ANSI TIA/EIA-422-B, TIA/EIA-423-B, and ITU Recommendations V.10 and V.11. The Module has PCIe x1 route to Port 4 or Port 8.
-
Product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-02 And WMA-02LF
-
The Falco Systems WMA-02 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 4mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-02LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.2mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Product
Erbium Doped Fiber Amplifier
EDFA
-
Optoplex designed and produced high power single-mode and polarization-maintaining EDFA, which met MSA compatible requirements. C-band MSA EDFA Module with +23 dBm Output Power is Optoplex standard product. Optoplex designed Pre-EDFA provides more than 35dB gain with -40dBm input power. The Double-Cladding pumped EDFA produces 2W output power.
-
Product
High-Speed System Synchronization and Distribution Amplifier - 3U VPX
Model 5903
-
- Multi-board synchronization with Quartz RFSoC video- Synchronizes up to 64 channels across eight Quartz® boards- Synchronizes sampling and data acquisition for multichannel systems- Provides single sample accurate synchronization between multiple channels and multiple boards- Synchronizes gating and triggering functions
-
Product
Amplifier Module
LNAM-B
-
Fully differential ultra-low-noise voltage amplifier module (LNAM) with selected bipolar rf transistors at the input stage. The amplifier exhibits ultra-low voltage noise, very high speed, and good dc precision. 50 Ohm input termination realized by negative feedback allows for the lowest possible noise temperature.
