Isolation Amplifiers
-
Product
Optical Parametric Amplifier
-
AVUS is an Optical Parametric Amplifier (OPA) that provides widely tunable high energy pulses and high repetition rates (up to 1 MHz). AVUS offers highest average output power on the market and is designed for 1 µm fs pump lasers.
-
-
Product
IDoor Module: 24-Channels Isolated Digital I/O With Counter MPCIe, DB37
PCM-27D24DI
Card Storage Module
Meets Advantech Standard iDoor TechnologyPCI Express® Mini Card Specification Revision 1.2 compliantSupports wide-input/output voltage (10-30 VDC/5-30 VDC)High over-voltage-protection (70 VDC) and voltage isolation (2,500 VDC)Easy configuration & efficient programming by Advantech DAQNaviI/O address automatically assigned by PCIe plug & playKeeps the output settings and values after system hot resetSupports Embedded Automation PC UNO-2200/2300/2400 seriesSupports Control DIN-Rail PC UNO-1300/1400 seriesSupports Control Cabinet PC UNO-3200/3300/3400 seriesSupports Control Panel Computers TPC-xx81/xx82 seriesSupports Thin Client Panel Computers TPC-xx51 series
-
Product
Erbium Doped Fiber Amplifier
S-102
-
The EDFA slot module of FOTS system with built-in power booster EDFA module offers a special function that is able to change the optical signal amplification feature variously, which is followed by user’s driving embedded pump LD freely. The output power of eash pump LD can be controlled separately by the program that is set up by user. When an optimum optical signal amplification particularity is needed, it is made up so that it can be materialized by choosing the Default mode provided along with User mode. More stable application of EDFA is possible through the monitoring of the factors such as in/out signal power, gain, alarm status and pump LD enabled by the application of FPGA processor which makes high speed driving possible. It is also set up that user’s present-time monitoring and control through LCD monitor of system main frame or GUI display for remote control can be possible. Through optimization of amplifier gain, noise figure, and saturated output power, this EDFA module will expand test capabilities in systems, components or sub-assembly manufacturing.
-
Product
High Voltage Linear Amplifier
A400X
-
This unit is a version of A400 amplifier equipped with two inputs, DC-offset and output atenuation. Input A is a normal non-inverting one. Using this input alone makes A400X functionally identical with A400 amplifier.Input B can act as a inverting or non-inverting depending on the position of the corresponding switch.
-
Product
16 Relay Output Board, 8 Isolated Digital Input Channels, 24V
APCI-2200-16-8
-
16 electromechanical relays with change-over contacts ? Max. switching voltage for the relays: 60 V/DC, 48 V/AC ? Max. switching current: 1 A ? Short response time ? Option: 8 input channels for AC voltage, optically isolated, input voltage range: 12 - 24 V DC ? Watchdog: software-programmable release, stop and time selection.
-
Product
Instrumentation Amplifiers
HIGH-POWER RADIO FREQUENCY (RF) AND MICROWAVE AMPLIFIERS, TWTA AND SOLID STATE
-
Communications & Power Industries
Electromagnetic compatibility (EMC) high-intensity radiated field (HIRF) testing, military testing, electronic warfare simulation and scientific applications are based on the same switched-mode power supply technology as its rugged amplifiers. As a result, these instrumentation amplifiers have all the same performance and reliability advantages as the rugged product line, but have been neatly re-packaged into compact, lightweight and affordable rack-mountable units more suitable for less demanding physical environments. CPI TMD's new modular design (the PTCM range) has many user benefits, including advanced self-diagnostics, ethernet interfaces, remote management, VSWR protection and plug and play field replaceable power supplies.
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel, V/I Readback, 1 kV Isolation
41-752A-111
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Microwave Power Amplifier 1/4 Watt, 10 MHz to 40 GHz
GT-1040A
-
The Spanawave/Giga-tronics GT-1040A Microwave Power Amplifier incorporates broadband MMIC-based architecture. These state-of-the-art amplifiers are based on solid-state parallel MMIC design with exceptionally wide bandwidth and high power. The unique circuit topology is highly reliable, with performance that excels where extremes of bandwidth and power are demanded.
-
Product
USB / RS232 / RS485 / RS422 Opto Isolators
-
USB has now moved from the desktop to more challenging environments, including instrumentation, point of sales, factory & building automation, etc. With our rugged, industrial-grade USB isolators and USB to RS232 / RS485 / RS422 optically-isolated converters, we ensure that your assets are well protected from unexpected events.
-
Product
Ultra-low Noise High Voltage Amplifier
WMA-200
-
The Falco Systems WMA-200 model is a high quality, high voltage, linear laboratory amplifier optimized for experiments requiring world-class, ultra-low output noise. The excellent noise performance, combined with the wide bandwidth and large voltage range make this amplifier the preferred choice for the most demanding precision positioning systems. The amplifier will routinely enable sub-atomic positioning resolution with piezo positioning systems and MEMS devices. Two WMA-200 amplifiers and a WMA-IB-LN phase inverter - buffer can be used to double the output voltage.
-
Product
Amplifiers
-
Motion Control Systems'' linear amplifiers are high performance servo controllers that produce very smooth sinusoidal motor currents using a linear amplifier output stage. In combination with a sinusoidally wound MCS brushless motor, the linear amplifier can achieve extremely precise rotational control with less than 1% torque ripple, no acoustic noise and almost undetectable levels of electromagnetic interference. Standard programmable features allow greater design flexibility, easy installation and start-up.
-
Product
Logarithmic Amplifiers
-
Pasternack Logarithmic amplifier category includes a wide range of log amp components. Log amplifier products in this logarithmic amp category are built to precise RF and microwave industry specifications. Logarithmic amplifiers, like the other over 40,000 RF, microwave and millimeter wave components at Pasternack are in-stock. Not only are these logarithmic amp components in stock, they also ship the same day.
-
Product
16-bit, 100KHz, 8SE/4DIFF A/D Inputs; 4 14-bit, 30KHz D/A Outputs, 4 24V Digital I/O, All Isolated
APCI-3120-8-4
-
*Optical isolation 500 V*8 SE or 4 diff. inputs*Data transfer rate: 100 kHz*16-bit resolution*4 analog output channels*Data transfer rate:30 kHz
-
Product
Isolated Digital I/O Card
PCIe-IDIO-24
-
This product is a x1 lane PCIe isolated digital input and FET output board with Change of State (COS) detection capabilities. In addition to the isolated signals, 8 (or 4) TTL/CMOS input/output pins are available, for your application’s convenience.
-
Product
Low Noise Amplifier
-
R&K’s Low Noise Amplifier (LNA) series products are a type of small signal amplifiers but with excellent noise figure. LNA is designed to significantly minimize additional noise to be introduced inside the product, and capable to amplify the input RF signal to the required level with minimal impact from noise on output RF signal.
-
Product
4-Port Isolated RS-232/422/485 With IRIG B Card
ECU-P1624D
-
industrial communication module designed for high-reliability, time-synchronized serial data transmission. It supports four software-configurable RS-232/422/485 ports, often including isolation for interference protection, alongside an IRIG-B time synchronization input, commonly used in substation automation.
-
Product
PCIe Digital I/O Board, 64 Optically Isolated I/O Channels, 24V
APCIE-1564
-
32 digital inputs, 24 V, isolated16 interruptible inputs32 digital outputs, 24 V, isolated, 10 to 36 V, 500 mA/channelOptical isolation 1000 VWatchdog for resetting the outputs to "0" (when Power-On)Protection against fast transients, overvoltage, electrostatic discharge and high-frequency EMIInputs: voltage reversal, input filtersOutputs protected against short circuitOvertemperature and overvoltage protectionDiagnostic report in case of short circuits, overtemperature, voltage drop ...24 V power outputs with protection diodesShutdown logic when the external supply voltage drops below 5 V
-
Product
Saluki S3871X Series Solid State Power Amplifier (max. 500W output power)
-
S3871X series is a broadband benchtop solid state power amplifier and incorporates the patended spatial power combination technology. It is designed to have features of broad bandwidth, high gain, high power, wide dynamic range, low spurious signals and extremely load tolerant. These features enable the amplifier to be used as a cable test instrument covering multiple frequency bands.*Wide frequency range, 9kHz to 110GHz, max. 500W output power*
-
Product
Multi-Channel Modular Isolated Power Supply
N6700 MPS
-
N6700 MPS has 16 different DC power supply modules, so test system designers can use these modules according to their specific test requirements to establish 1 to 4 channel DC power supply system. In the requirements of speed and accuracy of the occasion to invest in high-performance output, and for the general requirements of the DC power supply to buy basic performance output.
-
Product
Mixer Amplifiers
-
Tailored for various establishments such as restaurants, schools, churches, clubs, and more. This versatile unit offers a compact and highly efficient solution to seamlessly blend up to three audio sources.
-
Product
PXI 5A MUX, 2-Bank, 24-Chan, Ind. Isolation
40-651-102
Multiplexer Module
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel. 4-bank 11-channel. 8-bank 5-channel. Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
Product
5B Measuring Amplifiers
MA Series
-
Highest aim of our connection technology is user-friendliness. Very comfortable is the connection of our products to the most various sensors and signals.
-
Product
SpaceWire Isolator
134
-
The SpaceWire Isolator is an isolation unit for ground test and integration applications, providing galvanic isolation for two SpaceWire links. Isolation is tested to 60 V with components rated to 100 V and 2500 V max transient voltage.
-
Product
Amplifiers
-
Packaged and Die up to 26 GHzOver 145 MMIC Surface Mount and Die modelsConectorized models, power output to 100WHigh dynamic range, low noiseLow-cost, custom solutions available!
-
Product
Broadband Power Amplifier
PAS-08042-60
-
* Solid State Power Amplifier* Small Signal Gain: 60 dB typ.* Rack Mount Case* Internal Cooling Fans*Type N Connectors* Over-voltage, over-current protections
-
Product
RF Medium / High Power Amplifier
-
Corech Microwave’s RF medium/high Power Amplifier(PA) frequency ranges from 0.1 to 52 GHz, up to 100W high power output (CW or Pulse). Narrow-band & wide-band ready modules are available SMA, 2.92mm, 2.4mm, WR28, WR24 and PIN connector options are available.
-
Product
Ground Isolated ICP® Pressure Sensors For High Frequency
-
PCB® Series 102B is a ground isolated version of the Series 113B. These sensors have all of the same features and benefits of the 113B Series, plus the added benefit of isolation, which helps prevent ground loop problems. This series can accommodate an optional ablative coating (Prefix: CA) to protect the diaphragm from thermal shock in flash-temperature applications.
-
Product
Low Noise Amplifier (DC Powered)
-
RF Lambda’s DC low noise amplifiers (LNA) are broadband and offer low noise figure high IP3. Hermetically sealed options are available upon request.
-
Product
DIO-AIO Conversion Set For Conventional Power Amplifier
PAD64
-
PAD64 DIO(digital input/output)-AIO(analog input/output) Converter is the equipment which could be used for DI/DO (Digital input/Digital output) conversion and galvanic isolation between Real-time simulation system and protection equipment, and any other equipment which need AIO (analog binary input/ output, dry contacts).
