-
Product
AC/DC Clamp Meter
2660 CL
-
Standard Electric Works Co., Ltd
● 4000 counts.● Voltage measurement, current measurement, resistor measurement, frequency counter, capacitor measurement.● Bargraph indication.● Range change function.● Data hold function freezes the reading.● REL function.● Peak function.● Diode measurement.● Max / Min function.● Continuity check.● Low battery indication.● Auto Power Off (APO) function.● Safety design throughout with no exposed metal parts, shielded banana plugs and recessed input terminals.
-
Product
32-Ch Isolated Digital I/O And 1-Ch Counter PCI Card
PCI-1750
Digital I/O Module
16 isolated DI and 16 isolated DO channels.High voltage isolation on all isolated channels (2,500 VDC).High sink current on isolated output channels (200 mA/channel).Supports dry contact or 5 ~ 50 VDC isolated inputs.Interrupt handling capability.Timer/counter interrupt capability.
-
Product
NI-9425, 24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module
785044-01
Digital Module
24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module - The NI‑9425 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each digital input line is compatible with 24 V logic levels. The NI‑9425 offers isolation between the input and output banks from channel to earth ground. You cannot use the NI‑9425 in a CompactDAQ chassis to perform counter operations.
-
Product
Digital I/O Board, 32 Isolated I/O Channels, 24V +special EEPROM & TTL IO Port
APCI-1500-PULS
-
PCI interface to the 32-bit data bus Connector compatible to PA 1500 Connector and software compatible to CPCI-1500 16 isolated input channels, 24 V, including 14 interruptible 3 software-programmable counters/ timers 16 isolated output channels, 10 to 36 V, output current 500 mA Timer-programmable watchdog for the reset of the outputs"-PULS" version has a special EEPROM and a TTL IO port added at end of cardDiagnostic report through status register in case of short-circuit, overtemperature, voltage drop or watchdog Interrupt triggered through watchdog, timer, error One ground line for all inputs and one ground line for all outputs
-
Product
Suitable For Frequency And Pulse Sensors
SEM1600F
-
The SEM1600F is a cost effective “smart” powered conditioner that accepts all common process pulse signals with a frequency range between (0.01 to 65000) Hz in standard configuration and (DC to 1000) Hz in counter mode. Typical applications would be to measure flow or batch counting.
-
Product
Isolated Programmable Multifunction Counter Board, LACQUERED
APCI-1710-LAC
-
Wide application possibilities through free combination4 modules with numerous functions quickly and easily programmable Each of the 4 modules is programmed with a function. The 4 modules can either be programmed with the same function or freely be combined with 4 different functions.
-
Product
NI-9361, 32-Bit, 8-Channel C Series Counter Input Module
783407-01
Counter Input Module
32-Bit, 8-Channel C Series Counter Input Module - The NI‑9361 is a differential or single-ended input module. With this module, you can expand beyond the four counters in CompactDAQ to reach up to 64 counters per 8‑slot chassis. You can configure each channel to read a single pulse train or combine them to read up to four incremental encoders. You can also directly connect sensors with open-collector or push-pull outputs by using an internal switchable 1 kΩ pull‑up resistor. The NI‑9361 counters can perform encoder position and velocity measurements. You can synchronize the counters with other analog, digital, and counter measurements in your chassis.
-
Product
Integrated Potentiostat and Multiplexer
EmStatMUX8
-
Based upon the EmStat range, there are two types of multiplexers to suit most types of sensor array work. The MUX8 is the most flexible offering the ability to connect arrays made of up to eight working electrodes in two or three electrode cell types and chips sharing a reference electrode and/or counter electrode. The MUX16 is suitable for sensor arrays or chips with sixteen working electrodes all sharing a RE and/or a CE. Both instruments are suitable for laminated layer corrosion analysis.The potentiostat is controlled and powered by USB and is used with PSTrace allowing for simultaneous sampling of each channel at a rate of 25 ms/channel. Standard packaging includes a shielded cable with connections for a working, a counter and a reference electrode by means of 2 mm banana connectors and mini-crocodile clips, a stripped end, Dsub-37 terminated flat cable and a USB cable. To make connections to chips simpler the Connection Terminal is an optional extra providing clearly marked screw terminals to the electrodes and can be directly joined to the ESMUX via their D-Sub connectors.
-
Product
250 KS/s, 16-Bit, 8-Ch, Simultaneous Sampling, Multifunction PCIE Card
PCIE-1812
-
8 differential simultaneous sampling analog inputs, up to 250 kS/s, 16-bit resolution2 analog outputs, up to 3 MS/s, 16-bit resolutionFull auto-calibration2 analog triggers and 2 digital triggers for AI/O32 programmable DI/Os with interrupt functionsFour 32-bit programmable counters/ timers/ encodersBoard ID switchSupport for Microsoft Windows 10/11
-
Product
ICI Mace Snag Tester
TF220
-
TESTEX Testing Equipment Systems Ltd.
ICI Mace Snag Tester. To determine the tendency of fabrics to snag (pull yarn loops from fabric) in normal wear (mace snag).Provided with 4 rotating test cylinders fitted with sleeves of test fabric, mace balls with tungsten carbide points and controlled by a predetermined electronic counter.
-
Product
Parts Counter
TruView™ Parts Counter
-
Designing a contactless parts counter you don’t have to bolt to the floor. A machine that can be easily moved around your facility (it has casters!). A parts counter that runs on batteries so you can use when the lights go out. A TruView™ Parts Counter that counts parts accurately.
-
Product
Mini Receiver
FB7-NX
-
In about 1935, the National Radio Company of Malden, Mass., brought out a “hot” high frequency receiver, called the FB7, and the subsequent FB-7X. It featured a super-hetrodyne design with plug-in coils that gave it a broad frequency range. The “X” model also incorporated a crystal filter in the intermediate frequency section, thus giving it additional selectivity. The receiver was viewed by radio amateurs as a technological breakthrough, and it was also used commercially for point to point high frequency communications. As the receiver did not have an internal RF amplifier section, a separately tunable RF amplifier was later provided in a separate enclosure for additional performance capabilities. Now, National RF, Inc., is resurrecting the fabled receiver name with an all solid-state, hot mini receiver, which also utilizes plug-in coils to cover the HF spectrum. The mini-receiver is designed for use by radio amateurs as well as serious short-wave listeners, and allows reception of AM, CW, and SSB signals. It incorporates a super-hetrodyne design with a dual gate FET built-in RF preamplifier and a ceramic filter for selectivity, often required when used in a crowded amateur radio band. In addition, the receiver has a buffered rear panel output of the high frequency oscillator for use with either a frequency counter for exact receive frequency display, or for interface with an outboard transmitter. A rear panel jack is also provided for muting the receiver when a transmitter is placed into the transmit mode. And, the receiver is small enough to fit into carry-on luggage and taken on trips when it is desired to “keep an ear” on amateur radio or other high frequency activity. The receiver utilizes rear panel plug-in coil assemblies which contain the RF amplifier, mixer, and oscillator tuned circuits. Each plug-in coil assembly also comes with a separate dial scale, which is inserted onto the front panel for displaying the tuned frequency. A very smooth 6 to 1 planetary drive is used for tuning the receiver. Other front panel controls include RF preamplifier peak, volume control, Beat Frequency Oscillator adjustment, and RF gain control. Other switches include filter bandwidth, AM/CW/SSB selection, Power, and a general coverage/band spread control for certain plug-in assemblies. The receiver is intended to drive head-phones via a rear panel jack, but has sufficient output to drive a small external speaker.
-
Product
Three Phase Din Rail Energy Meter Type DTS999D
-
Bofa Instrument & Equipment Co., Ltd
Three phase DIN Rail energy meter type DTS999Dis a new type of three phase electronic energy meters, which completely accords with international standard IEC61036. It can display energy consumption by stepping-motor counter or LCD. It features good reliability, small volume, light weight and convenient installation.
-
Product
Generator Monitoring Unit
-
Avoids the requirement of 2 different meters (energy and VAF in one)Reduces the cost and simplify wiringHigh resolution reading with auto scaling in LEDEnergy consumption in counter even if CT is reversed
-
Product
8DI/8DO (Source Type) IoT Modbus/SNMP/MQTT Ethernet Remote I/O
ADAM-6052
Ethernet I/O Module
8ch digital input(counter)/8ch source type digital output(pulse output)Protocols:MQTT(TLS),SNMP,Modbus TCP,RESTful API,ASCIIGCL to perform basic logic control rulesPeer-to-Peer function to map I/O statusCloud access: Data update to AzureBuilt-in web serverWatchdog timer to recover the system
-
Product
Elongation Tester
SC-5
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.3-2008/IEC60851-3; Inspection standard: JB/T4279.3-2008Used to test elongation (ductility) of copper wires covered with φ0.100-3.0 mmenamel, silk or other insulation materials and other metal wires with tensile strength ≤2000N;Application of SCM control allows for fast operation and strong anti-interference capacity;Preset elongation of samples with two-digit toggle switch and, when the preset value is reached during test, motor and counter would automatically stop action and display results;The instrument is capable of measuring elongation while also the tensile force and holding the maximum tensile force value during stretching;Clamps are designed according to characteristics of various wires to prevent samples from breaking at clamp jaws, easy to load samples and, after samples are compressed, enamel can be automatically broken;While sample is broken, movable clamp would automatically stop moving, with error between displayed and actual elongation value less than 1%;
-
Product
Geiger Counter
ONYX®
-
ONYX features a modern, streamlined look and the use of advanced technologies, making it a one-of-a-kind Geiger Counter. It weighs only 7 oz. (200g.) and measures a mere 5.1 X 2.6 X 0.9 in. (72 X 37 X 13 mm.) making it easy to transport. Despite its compact size ONYX is capable of detecting alpha, beta and gamma radiation with the same sensitivity as the IMI Inspector Alert™, and like the IMI Inspector Alert™ V2, ONYX is optimized for surface contamination measurements through use of its 2 in. pancake Geiger Mueller tube.
-
Product
Voltmeter
-
The Voltmeter (like the Sound Level Meter and Frequency Counter) can be positioned anywhere on the screen. The size of the display font changes when you resize the meter by dragging its borders. You can fill the screen for a really big readout that can be seen from across the room.
-
Product
48-Ch Digital I/O And 3-Ch Counter PCIE Card
PCIE-1751
Counter/Timer Card
48 TTL digital I/O linesEmulates mode 0 of 8255 PPI (every port with nibble)Supports both dry and wet contactInterrupt handling capabilityTimer/Counter interrupt capabilityBuffered circuits for higher driving capacity than the 8255Keeps the I/O port setting and DO state after system resetBoardID switchPattern match interrupt function for DIChange of state interrupt function for DIProgrammable digital filter function for DI
-
Product
Digital I / O modules
-
The 34950A module has 64-bit bi-directional lines and can be configured with 8 8-bit digital I / O channels with handshaking capability. Each 8-bit channel has programmable polarity and a threshold of up to 5V. The memory can be used to generate or capture digital patterns up to 10 MHz. It provides seven configurable handshaking protocols for a wide range of applications. In addition, two counter / totalizer channels can be used to compute events, frequency, period, duty cycle, accumulation, and pulse width.
-
Product
Multi-Spectral UV/Laser Range Stimulator
Phantom™
-
The Phantom is a long-range laser and ultraviolet (UV) stimulator capable of testing aircraft electro-optical sensor suites up to 5 km. Phantom can operate as an independent laser and/or UV stimulator or can be integrated with our other electro-optical and radio frequency range systems (see GTESS and PRTS). The Phantom provides both a laser threat and a synchronized temporal missile plume signature to stimulate both the aircraft’s laser and missile warning systems. Training aircrew to counter maneuver a Laser Beam Riders (LBR) threat is considered essential to survival and in-air training. The Phantom can be deployed either on a shoulder or tripod mount.
-
Product
Cam Switches
-
Mechanical row-position counters with an exchange unit are available for standard applications and for applications with safety switching points. The whole ram unit can be removed using two bolts to replace the individual ram. This saves time and money if service is required because it is not necessary to remove the whole switch. The switches are recognizable by the blue-colored anodized ram plate
-
Product
Power Limiters
-
Keysight's power limiters provide the best broadband input protection from excess RF power, DC transients and ESD, for a variety of RF and microwave instruments and components. For example, the input circuitry of spectrum analyzers, network analyzers, frequency counters or amplifiers can be protected from unintentional inputs up to 5 watts average power. At even greater power levels, failure mode for the limiter is either an open circuit or a short circuit to ground, thereby protecting the instrument from damage.
-
Product
PCI Digital IO Board
-
*Bus Interface: PCI Bus*Counter/Timer: 16 Channels*Counter Size: 32 bit*Max. Source Frequency: 80MHz*Compatibility: 5 V TTL/CMOS*Discrete Inputs: 24 Channels*Discrete Outputs: 24 Channels*Pulse Generation: 12 Channels*Bi directional I/O's: 8 Channels*Oscillator stability: 50 ppm*Op-to isolation for I/O's*DMA buffered operation*16-bit data bus 32 bit Address bus for External Memory Interface*The Pulse Width and PRI of the pulses can be varied*The pulse generation frequency from 10Hz to 40MHz (25ns to 100msec)*The no. of pulses controlled from 1 to 255 pulses*All the pulse input and the output signals and Bi-directional write signals driven through Pin Driver*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
Speed Pick-up
SU63
-
The Validyne SU63 is an AC inductive speed pick-up used for RPM measurement on high-speed rotating equipment. The SU63 is a tightly-wound coil with a laminated core that can be conveniently mounted on rotating equipment so that the magnetic field of a magnetized nut or part passes through the coil windings. The moving magnetic field produces a voltage within the coil proportional to its rate of change and the strength of the permanent magnetized part. The frequency of this inductive voltage spike is fed into an oscilloscope or counter to determine RPM.
-
Product
PCI-6143, 8 AI (16-Bit, 250 kS/s/ch), 8 DIO, PCI Multifunction I/O Device
778913-01
Multifunction I/O
The PCI‑6143 is a simultaneous-sampling, multifunction DAQ device. It offers analog input, digital I/O, two 24‑bit counters, and digital triggering. The PCI‑6143 is ideal for a variety of applications, such as … high-energy physics, ultrasonic and sonar testing, ballistics and highly transient signals, and multiaxis control. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Counter And Rate Meters
-
We carry a wide range of counter and rate meters including totalizers, batch controllers, and more. Available with pulse, magnetic or DC pulse, analog, voltage, current, and frequency input types.
-
Product
Test Module
MTC
-
The measuring channels can be connected depending on the application to the pins on the system interface or to the six internal bus lines.Four measuring channels per module on 8:1 multiplexer = 32 InputsUp to 4 parallel measurements per MTC (4 parallel counters)Intelligent algorithms for fast measurements even at low frequenciesFrequency, period, pulse width, rise- and falling time as well as event counting on each channelTime measuring range: 10 ns - 42 s, resolution 10 nsFrequency measuring range: 0.015 - 100 MHzEvent counting: 0 - 232, maximum 100 MHzMax. input level/trigger voltage: +/-100 VSynchronization with external trigger possible
-
Product
Software for Magnii Geiger Counters
RadGraph & RadMeter Suite
-
RadGraph is a comprehensive program that allows graphing readings over time, saving graphs as images and CSV data, printing graphs, analyzing radiation levels over time and also taking simple measurements.
-
Product
5 / 10 / 20 MHz Multiwaveform Arbitrary Signal Generator
MASG Series
-
- Economic and Light Weight- Dual Output with Same Characteristic- 1µHz Frequency Resolution- 11 Built-in Waveforms and 5 User defined Arbitrary Waveforms- AM, FM, PM, PWM, FSK Modulation, Frequency Sweep and Burst Function- Built-in 100MHz Frequency Counter- Arbitrary Waveform Editing PC Software- USB Host, USB Device
