Wave
undulation up-down synced with to and fro. Scope of site
See Also: Long-Wave IR, Lightwave, Shear Wave, Sub-mm Wave, Microwave, Wavelet, Continuous Wave, Submillimeter Wave, Sine Wave, Millimeter Wave, Shock wave, Ocean, Quantum, Gravity, Particle, Seismic
-
Product
MHV Connectors
-
Pasternack MHV connector category includes dozens of part numbers, most are RoHS and REACH compliant. MHV connector series in this category will terminate to coax or terminal. Our MHV connectors are built to precise microwave and RF industry specifications. Connectors in MHV series are constructed in male or female gender with 50 Ohm impedance. MHV connectors are available in straight or right angle versions, as well as, bulkhead, 4 hole panel or mountless options. These MHV connector designs include clamp/solder, crimp/solder or solder attachment methods. As with the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this MHV connector series is in-stock. Not only in stock, but these coaxial connectors will also ship the same day as they are purchased.
-
Product
C-Band DWDM Line Amplifier EDFA (WLA-C)
HWA4200 (With SNMP)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HWA4200 series, is designed for C-Band 44 waves or 88 waves DWDM system design Line Amplifier gain flatness. Products using the most excellent optical performance, the most advanced electronic control technology and comprehensive software features, has a wide operating wavelength range, Low noise, excellent gain flatness characteristics and transient characteristics.
-
Product
Guided Wave Radar (GWR)
VEGAFLEX
-
In level measurement with guided wave radar, microwave pulses are conducted along a cable or rod probe and reflected by the product surface. The measuring probe of the TDR sensor ensures that the signal reaches the medium undisturbed. Liquids, bulk solids and separation layers (interfaces) in liquids are commonly measured with this measuring technique.
-
Product
Time-Resolved Electrochemical Quartz Crystal Microbalance
400C Series
-
The quartz crystal microbalance (QCM) is a variant of acoustic wave microsensors that are capable of ultrasensitive mass measurements. Under favorable conditions, a typical QCM can measure a mass change of 0.1-1 ng/cm2. QCM oscillates in a mechanically resonant shear mode under the influence of a high frequency AC electric field which is applied across the thickness of the crystal. Figure 1b below shows an edge view of a QCM crystal undergoing oscillatory shear distortion. The central portions of the top and bottom of the crystal are coated with a typically disk-shaped thin metal film (e.g., gold).
-
Product
75 Ohm BNC Connectors
-
Pasternack 75 Ohm BNC connector category contains many part numbers, most are RoHS and REACH compliant. 75 Ohm BNC connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Pasternack 75 Ohm BNC connectors are built to precise RF and microwave industry specifications. 75 Ohm BNC connector are available in male or female gender with 75 Ohm impedance. BNC 75 Ohm connectors are available in straight or right angle versions, as well as, bulkhead, 4 hole panel or mountless options. These 75 Ohm BNC connector designs include clamp/solder, compression, crimp/solder or solder attachment methods. We offer 75 Ohm BNC connector with standard or high performance levels constructed with brass or stainless steel bodies. Like the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this 75 Ohm BNC connector group is in-stock. In addition to being in stock, these BNC 75 Ohm connectors will ship the same day as they are purchased.
-
Product
AM Antenna Tuning Units
ATU's
-
LBA medium wave AM Antenna Tuning Units (ATU) and Line Tuning Units (LTU) are impedance matching units designed to match the transmitter to the impedance of the transmission line or the antenna system. Our Antenna Tuning Units are available for both series-fed and {ln:Tunipole antenna systems} Tunipole™ antenna systems to powers in excess of 500 kW.
-
Product
Oscilloscope - 350 MHz, 2 Analog Channels
DSOX4032A
Oscilloscope
350 MHz2 analog channels Easily view signals on the large 12.1-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering Capture more data with 4 Mpts memory and standard segmented memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, digital channels, dual-ch 20 MHz arbitrary Wave Gen, 3-digit DVM, serial trigger and analysis & mask testing
-
Product
NIR & UV-VIS Process & Lab Analyzers
-
Our Guided Wave complete analytical systems utilize proven Near Infrared (NIR) and Ultraviolet / Visible (UV-VIS) spectroscopic techniques. We deliver a total solution that includes optically matched components and a well-planned calibration approach leading to long-term success and savings. Our state-of-the-art systems are designed for continuous online use, providing real-time data of laboratory quality while thriving in the most demanding processing plant environments. We work with you to tailor a solution for your exact requirements from analyzer to interface.
-
Product
Instrumentation HPAs
-
Communications & Power Industries
CPI SMP Division provides a complete line of high-powered continuous wave (CW) and pulsed instrumentation amplifiers for EMC testing, available in octave and multi-octave bandwidths from 1.0 GHz to 95.0 GHz and power levels exceeding 2.0 kW to meet the new military and automotive standards. CPI is the only supplier that manufactures both the traveling wave tube (TWT) and the TWT amplifier.
-
Product
Online Monitoring Systems
-
RAEM system is the latest IIoT-AE product series for remote unattended acoustic wave (acoustic emission) long term monitoring applications. There are a few types of RAEM series products available:RAEM1 is a single channel full function version of RAEM.RAEM1-6 is a 6-channel integrated clock synchronized version.RAEM2 is a single channel time trigger power saving compact version.The Qingcheng IoT Cloud platform is an cloud platform for RAEM and IoT devices to upload or download data, to display AE waveform, parameters and alarm information, to remote read and write devices, to send alarm notifications to users via SMS and emails and more.
-
Product
Plane Wave Converter
PWC200
-
The R&S®PWC200 Plane Wave Converter is a bidirectional array of 156 wideband Vivaldi antennas placed in the radiating near field of the device under test (DUT). The phased antenna array can form planar waves inside a specified quiet zone within the radiating near field of the 5G massive MIMO base station for realtime radiated power and transceiver measurements (EVM, ACLR, SEM, etc.).
-
Product
Antennas
-
Is a specialized transducer that converts electric current into electromagnetic (EM) waves or vice versa.
-
Product
Dual 8 To 1 Terminated 50Ω 600MHz PXI RF Multiplexer
40-763A-002
Multiplexer Module
The 40-763A-002 terminated dual 8 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
Product
Low Noise Amplifiers
-
LNA amplifier PE15A1000 is rated at 13 Volts DC maximum and 200 mA. Our low noise radio frequency LNA amp is part of over 40,000 RF, microwave and millimeter wave components available from Pasternack. This coaxial millimeter wave low noise amplifier can ship worldwide the same day of the purchase as with our other available RF parts.
-
Product
Quad 4 To 1 Terminated 50Ω 600MHz PXI RF Multiplexer
40-761A-004
Multiplexer Module
The 40-761A-004 terminated quad 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
Product
Drop Tester
KD 688 A
-
King Design Industrial Co., Ltd.
*PLC control, linear motor fast speed control the height setting.*Alarm warning before testing.*Light support structure decreases the test impact.*Support dropping very smooth with dual lubrication guide.*No second impact. *A data acquisition for the impact wave record (Option).*Non maintenance request for continue operation.*According to ISTA, ASTM .....etc international standard.*Equipped edge & corner holder.
-
Product
Single Photon Detector System For Near-Infrared (0.7 - 1.3 Um Wavelength)
-
Single Photon Detector System for Near-Infrared (0.7 - 1.3 um wavelength) waves with Closed-Cylce (cryogen-free)cooling
-
Product
Oscilloscope - 500 MHz, 4 Analog Channels
DSOX4054A
Oscilloscope
500 MHz4 analog channels Easily view signals on the large 12.1-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering Capture more data with 4 Mpts memory and standard segmented memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, digital channels, dual-ch 20 MHz arbitrary Wave Gen, 3-digit DVM, serial trigger and analysis & mask testing
-
Product
Impulse Current Generator
-
Weshine Electric Manufacturing Co., Ltd
Impulse current generator is mainly used to test the ability of electrical equipment to withstand strong impulse current, widely used in lightning arresters and electrical and electronic equipment in operation conditions of oscillation wave immunity test, can also be used for other research tests.
-
Product
Acoustic Control System
-
m+p VibControl performs acoustic testing in reverberation chambers and direct field environments as well as progressive wave tube testing. It is a fully automatic digital control system, providing fast, accurate and repeatable control of high-level noise to a reference octave band spectrum and the overall sound pressure level (OASPL). The control guarantees a high level of product safety.
-
Product
75 Ohm 1.6/5.6 Connectors
-
Pasternack 75 Ohm 1.6/5.6 connector category includes many part numbers, the majority are RoHS and REACH compliant. 75 Ohm 1.6/5.6 connector series in this category will terminate to coax or PCB (printed circuit board). Our 75 Ohm 1.6-5.6 connectors are built to precise industry specifications. 75 Ohm 1.6-5.6 connectors are constructed in jack or plug gender with 75 Ohm impedance. 75 Ohm 1.6/5.6 connectors are available in straight or right angle versions, as well as, bulkhead or mountless options. These 75 Ohm 1.6-5.6 connector designs include clamp/solder, crimp/solder or solder attachment methods. Like the other over 40,000 RF, microwave and millimeter wave Pasternack products, this 75 Ohm 1.6/5.6 connector series is in-stock. Not only are these 1.6 / 5.6 connectors in stock, but they also will ship the same day as they are purchased.
-
Product
Combination Wave and EMC Surge Generators
-
Shanghai Guantu Technology Co., Ltd.
Surge generator is an electronic measuring instrument used in the fields of information science and system science, electronics and communication technology.
-
Product
AC Electronic Load
-
The electronic AC loads cover a wide variety of different voltage, current and power ranges. All the AC loads are programmed with 11 different sine, square and DC waves. With 5 crest factor variations of each, a total of 55 waveforms are available. An external input is also provided to enable the user to amplify signals from a waveform generator.AC Loads allow real world operating conditions to be simulated. Typical applications include circuit breaker, transformer & UPS output testing along with general laboratory and research work.
-
Product
Attenuator Assemblies
-
Any device designed to reduce the power of a wave or electrical signal without distorting it.
-
Product
SHV Connectors
-
Pasternack SHV connectors category has several part numbers, most are RoHS and REACH compliant. SHV connector series in this category will terminate to coax or terminal. These SHV connectors are built to precise microwave and RF industry specifications. SHV connector items are built in jack or plug gender with 50 Ohm impedance. Connectors in SHV series are available in bulkhead, 4 hole panel or mountless options. These SHV connector designs include clamp/solder, crimp/solder or solder attachment methods. As with other over 40,000 RF, microwave and millimeter wave Pasternack products, this SHV connector series is in-stock. Not just are they in stock, but these radio frequency connectors will ship the same day as they are purchased.
-
Product
Receiver
-
Beijing KeHuan Century EMC Technology Co,.LTD
A device or apparatus that receives electrical signals, waves, or the like, and renders them perceptible to the senses, as the part of a telephone held to the ear, a radio receiving set, or a television receiving set.
-
Product
Single Photon Detector System For Near-Infrared (1.6-2.3 Um Wavelength) Waves With Closed-Cyle Cooling
-
Single Photon Detector System for Near-Infrared (1.6-2.3 um wavelength) waves with Closed-Cylce (cryogen-free)cooling
-
Product
Antenna Tuner
DU-1500T
-
The DU 1500T optimizes the performance of your antenna and transmitter or SWL receiver by providing adjustable impedance matching.The DU1500T also measures the Power and Standing Wave Ratio (SWR), which allows you to tune the indicted SWR to the lowestpossible ratio for the selected transmit frequency.
-
Product
Power Frequency Transducer
PP1S
-
1. Measuring and conversion IEC 6882. Dielectrical strength IEC 688 4 KVac / 1 min.3. Impulse test ANSI C37.90 / 1989 IEC 255-3 5KV ( 1.2 x 50 us ) 3KA ( 8 x 20 us ) - current coil4. Surge test (ring wave) ANSI C37.90 / 1989 ( 3KV - 0.5us / 100KHz ) IEC 255-3 ( 2.5KV - 0.25ms / 1MHz )5. Adaptability for power system VDE 0110 6. Measuring reliability VDE 3540
-
Product
Other Environmental Testers
-
GAOTek’s environmental testers can be used to measure parameters such as humidity, temperature, wind speed or velocity, wind direction, air quality, electromagnetic waves, ionizing radiation and more. Environmental testers are applicable in climate monitoring to occupational health and safety (OHS) applications. Our environmental testers are useful tools for collecting data about the immediate surroundings. Depending on the model, an environmental tester can function as a data logger for long-term data by collecting and storing measurement data over a certain period. Our environmental test solutions are affordable and dependable and are perfect for general to specialized jobs.
