-
Product
Multi-interface Electronic Control Unit
-
The Mors Smitt CatEnergy control unit ECU is the most modular and scalable solution available on the market for all function using high voltage measurement. From Energy Measurement purpose to all essential train function, the CatEnergy ECU is the perfect compact system for all demanding application on existing and new build train.
-
Product
Hot Swap, Fault Tolerant, Ultra Reliable Power Supply
Series HSP
-
The Kepco HSP series provides mission critical power. HSP comprises a group of twelve models, eight 1000 watt power supplies with outputs from 3.3 volts to 125 volts and four 1500 watt power supplies with outputs from 24 volts to 125 volts. All models feature current-sharing for parallel redundant N+1 operation. Models with the or-ing diode, option R, are capable of hot swapping when plugged into Kepco¹s RA 60 series rack adapter. Models with a digital meter, option M, are also available (see photo, right). A mechanical keying scheme allows the user to define which power supply will plug into a specified slot in the housing. Output voltage and current limit settings are adjustable from the panel and may be remotely adjusted.
-
Product
AM Antenna Tuning Units
ATU's
-
LBA medium wave AM Antenna Tuning Units (ATU) and Line Tuning Units (LTU) are impedance matching units designed to match the transmitter to the impedance of the transmission line or the antenna system. Our Antenna Tuning Units are available for both series-fed and {ln:Tunipole antenna systems} Tunipole™ antenna systems to powers in excess of 500 kW.
-
Product
Digital Relay and Merging Unit Tester
POM2-3333
-
POM2-3333 Digital Relay and Merging Unit Tester is equipped with 6*12.5A and 6*120V outputs, 8 pairs of BI, 4 pairs of BO and 6 fiber optic ports, built-in GPS, supporting PPS, IRIG-B, PTP/IEEE1588 time synchronization.
-
Product
Programmable AC&DC Power Supply Unit
PADS
-
The energy feedback type programmable AC/DC power source with energy feedback unit equipped functions of voltage adjustable, frequency adjustable, harmonic controllable, low voltage ride through simulation etc.
-
Product
Signal, Patchcord, ITA, 72", QuadraPaddle Insert, Single Ended
7-151924000-072
Signal Patchcord
Signal, Patchcord, ITA, 72", QuadraPaddle Insert, Single Ended
-
Product
Fiber Optic Visual Fault Finder
VFF5
-
Used to verify continuity, test and find breaks in fibre links, locate pinched fibre strands in termination cabinets, or anywhere fibre optic cables are terminated and subject to mechanical damage.
-
Product
Measuring Display Unit Breakers
-
Mitsubishi Electric Automation, Inc
Measuring display units (MDU) are integrated with molded-case circuit breakers and earth leakage circuit breakers for measuring, displaying, and transmitting information on cable ways. This display unit closely monitors energy consumption by measuring current, voltage, power, electric energy, harmonic current, leakage current and power factor.
-
-
Product
FAult Detector and OScilloscope 9 Functions in 1
FADOS9F1
-
Prot-Ar-Ge Industrial Project Design R&D Ltd. Co.
2 unique features are added to the FADOS9F1 over the FADOS71. First feature is the Programmable DC Power Supply; It can be adjusted between 0-16V and 20-1500mA with power output; the DC Voltage/Current graphs of the electronic card power supply can be produced. The second feature is the “IR Remote Temperature Measurement Sensor”; this sensor is used to find the components that heat up by drawing too much current. Using these two features together may reduce the time for trouble shooting some malfunctions by 5 to 10 times. These features can be used as a new technique for trouble shooting.
-
Product
Discharge Units
-
ENTES Discharge Units are used in capacitor banks and provide quick discharge over short periods of time.
-
Product
Lighting Management Units
-
Highly integrated, flexible lighting management ICs support nearly all the illumination tasks performed in mobile phones.
-
Product
Cable Fault Location Equipment
-
Cable fault location by electromagnetic and acoustic methods (with high-voltage pulse transmitter, which is not included into the set)Detection of insulation deterioration on cables by contact and non-contact methods
-
Product
PXI Fault Insertion Switch, 7-Channel, Two Fault Buses, 20 A
40-194A-002
Fault Insertion Unit
The 40-194A-002 is a 7-Channel Fault Insertion switch with two fault buses, designed for the simulation of fault conditions in automotive systems. As well as high current handling of 20A, very low currents can also be switched.
-
Product
Multi-Band Dual-Channel Receiver/Combiner, Modular Unit with Integral Tracking Receivers and Bit Syncs
LS-28-DRSM Series
-
Lumistar offers the LS-28 series of high performance multi-band multi-mode RF Receiver/Combiners in several different versions including rack mount, portable and modular formats. Complete solutions from RF to bits and/or RF to UDP data broadcast in Chapter 10 format are available. Available at any frequency range from 215 MHz to 6000 MHz, data rates to 50 Mbps.
-
Product
Phasor Measurement Unit
Qualitrol PMU-9/18/36
-
A scalable and modular substation hardened Phasor Measurement Units for connection to up to ten three phase circuits to calculate and stream phasors.
-
Product
Multifunction Unit - Up to 80 Channels of Digital I/O for Observing and/or Recording 16 to 64 Channels of Pressure of Temperature
Trig-Tek™ 260B
Multifunction I/O
Delivers up to 80 channels of digital I/O for observing and/or recording 16 to 64 channels of pressure or temperature. Consists of a motherboard that connects up to four daughterboards to the IP 1553 serial bus.
-
Product
Travelling Wave Fault Location Test Kit
PH Series
-
PH series travelling waveform fault locating relay/equipment test set is a new device to meet the needs of testing and verification for travelling wave fault location equipment and protection relay with TWFL function.
-
-
Product
PXI-2515, 35-Channel, 0.25 A PXI Signal Insertion Switch Module
778572-15
Signal Module
35-Channel, 0.25 A PXI Signal Insertion Switch Module—The PXI‑2515 is a multiplexer switch module that enables connectivity by routing high-speed digital I/O (DIO) signals between a device under test (DUT) and an NI high-speed DIO device or a parametric measurement device. You can use modules such as PXI Source Measure Units (SMUs) and PXI Digital Multimeters (DMMs) with high-speed digital devices. With the PXI‑2515, you can perform parametric tests on digital pins without external connectivity or impedance mismatch challenges.
-
Product
Portable Interface Unit
1553-USB-PIU
-
The 1553-USB-PIU is a Portable Interface Unit providing full MIL-STD-1553 test, simulation and bus analysis capability in a compact self-contained unit, to connect via a USB interface to suitable host systems. The unit provides support for all 1553A, 1553B, McAir and STANAG 3838 variants in a self contained battery operated unit, and is supplied with a matching power supply and battery charger unit for desk-top use. The 1553-USB-PIU supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with comprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides a variable amplitude dual redundant 1553 interface. 2 Mbytes of dual ported RAM are provided. The unit is supplied with "C" Driver library, together with a Windows GUI, providing a user friendly software tool for all 1553 set-ups, data management and storage.
-
Product
Pole Mounted Detector of PtG and PtP faults in 6-69V Line
LineTroll 111K
-
The unit mounts 3-5m below the conductors and monitors all three phases. The indicator is powered by replaceable long-life lithium batteries which have a lifeexpectancy of 10-15 years. It provides a 360 degree visibility for indication both for transient faults and permanent faults.
-
Product
SIM, Module, Receiver, 90 Series, Fully Loaded with pairs of VTAC Standard Pass-Thru and Right Angle Inserts (610151106)
510170102
Receiver Module
This fully loaded SIM module kit comes with 34 pairs of VTAC Standard Pass-Thru and Right Angle Inserts (610151106). This kit also includes two PCB brackets for securing module to PCB.
-
Product
SIM Series - Snap-In-Module Inserts
-
VPC's latest high-speed technology allows for concerns about cycle life and lost time due to PCB soldering and changeout to be a thing of the past. The unique design of VPC's VTAC, QuadraPaddle, and Micro Power/Coax SIM inserts allows for changeout and replacement of pass-thru inserts while preserving either right-angle or vertical connections to the PCB.
-
Product
3 Function Slot MOSA Nano Data Concentrator Unit (DCU)
NIU3A-DCU-01
Data Concentrator Unit
NIU3A-RDC-01 is a Modular Open Systems Approach (MOSA) Data Concentrator with low power high performance ARM Cortex -A53 processing. 8 GB RAM, 32 GB SATA Flash, 2 x 10/100/1000Base-T Ethernet.
-
Product
Nano Interface Unit
NIU1A
-
NAI's NIU1A is a nano unit with an integrated power supply, one function module slot, and an optional ARM Cortex-A9 processor. This small, low-power unit is ideally suited for rugged military, industrial, and commercial applications, and delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in less time, with NO NRE.
-
Product
Front Panels & HMI Units
-
Elma produces front panels for plug-in units, enclosures, 19" sub racks and customer-specific applications. This includes all material, machining, printing and assembly.
-
Product
Combined Map Display Unit & Interface Unit Tester (COMED)
MS 1117
-
This system is used to test COMED (Combined Map Electronic Display) IFU cards. This ATE checks the LRU Status and card status and identify faulty component in the individual UUT. On fault, this suggests the possible component failure as diagnostic report, for repairing the cards.
-
Product
Fault Locator
REZAP MODULAR
-
REZAP MODULAR brings full REZAP functionality to fuse panels with severe space restrictions
-
Product
Cable Fault Meter
-
A cable fault meter can locate open power cables, either live or dead (without current), with voltages up to 300 V. A cable fault meter can locate cables, circuits, short circuits and ground wires. To perform these functions, it is not always necessary to disconnect electrically sensitive devices or to disconnect the power from the cable which is being tested. Many cable fault meter devices can also locate ferrous and non-ferrous metals, wood and plastic with high degrees of accuracy.
