-
Product
Penetration-Resistant Insert Flexing Tester
UI-FT05
-
Penetration-Resistant Insert Flexing Tester, also named as Steel Midsole Flexing Tester, is used to test penetration resistant inserts flexing resistance. As described in EN 12568, ISO 20344, the inserts shall exhibit no visible signs of cracking, disintegration or delamination after having been subjected to 1 *106 (one million) flexion cycles.
-
Product
Visual Fault Locator
TM191
-
TM191 series visual fault locator is used for the measurement in single mode or multi-mode fibers. It features a rugged design, a universal connectorand an accurate measurement
-
Product
Advanced Power System – Power Dissipater Unit, 1000 W
N7909A
-
The N7909A power dissipater unit adds current sinking or two-quadrant operation to any Advanced Power System (APS) N6900A or N7900A power supply. Each N7909A provides up to 1 kW of current sinking capability to an APS power supply, so you will need two N7909As to achieve full two-quadrant operation of a 2-kW APS supply. You can use a single N7909A unit with a 2-kW APS power supply to achieve 50% current sinking capability. The N7909A form factor is 1U and full rack width. N7909A connects to an APS power supply via a two-wire power connection and a communication connection to provide continuous two-quadrant operation. The connections are located on the rear panel of both the N7909A and the supply.
-
Product
VTAC, Insert Bundle, Receiver/ITA, SIM, Vertical Header and Pass-Thru
610151108
SIM Insert
Each kit contains (1) VTAC vertical header insert and (1) VTAC pass-thru insert. VTAC vertical header inserts get press fit into a PCB and by extension of the VTAC pass-thru insert, a VPC receiver connector can be mounted to the PCB. This is especially useful when mounting an i2 MX receiver or 90 Series SIM module to a PCB.
-
Product
SIM, Module, ITA, 90 Series, Fully Loaded with pairs of VTAC Standard Pass-Thru and Right Angle Inserts (610151106)
510171102
ITA Module
This fully loaded SIM module kit comes with 34 pairs of VTAC Standard Pass-Thru and Right Angle Inserts (610151106). This kit also includes two PCB brackets for securing module to PCB.
-
Product
Electronic Control Units
-
Self-contained engine management system and data logger for race engines up to eight cylinders. The unit is complete with integrated ignition and injection drivers and so needs no external units to run an engine.
-
Product
1.8-148 MHz Stand Alone Weatherproof Unit for the Application of DC Control Signals up to 400ma on your Coax Cable
Bias-T PLUS
-
The Array Solutions Bias-T PLUS is a 1.8-148 MHz stand alone weatherproof unit that permits the application of DC control signals of up to 400ma on your coax cable. By inserting the control voltage on the coax cable feed-line, you eliminate the requirement for external DC wires for powering remote devices.The Bias-T PLUS weatherproof assembly means that it can be placed indoors or outdoors for maximum flexibility. Typically, one Bias-T PLUS will be placed indoors for inserting DC on your coax feed-line, and one Bias-T PLUS will be placed at the remote device where the DC voltage is extracted.
-
Product
12/24 CH Insertion Loss/Return Loss Automatic Testing System
CA3201
-
UC INSTRUMENTS CA3201 12/24 CH INSERTION LOSS/RETURN LOSS AUTOMATIC TESTING SYSTEM is special designed for MPO/MTP fiber cable and multi-channel fiber optical devices like PLC device. It also can be easy changed into AWG DWDM devices testing system ifwe change 1310 /1550 nm light source into UC INSTRUMENTS’ tunable laser source.
-
Product
Visual Fault Locator VFL X5007
-
Metal case, Rugged and durableLow battery indication, to avoid leakage and wrong judgmentESD protection design, Protect the LD effectivelyIntegrated case, to avoid the case intermediate brokenRe-changeable ceramic tube, to avoid returning to manufacturer for this small faultLong battery life, up to 60 hours＠1mW
-
Product
Server Power And Back Up Unit Test Solutions
-
Built on the proven Chroma 8000 ATS platform, these customizable solutions are specifically designed for automated testing of server PSUs, power shelves, rack power systems, bidirectional DC/DC converters for BBUs, and low-voltage high-current DC/DC converters for motherboards.
-
Product
GPIB-ENET/1000, Ethernet GPIB Instrument Control Device - United Kingdom 240VAC
781630-06
GPIB Controller
The GPIB‑ENET/1000 is an IEEE 488 controller device for computers with an Ethernet port. You can use this device to share a single GPIB system among many networked users or to control several test systems from a single networked host. The GPIB‑ENET/1000 features a password-protected web interface for easy configuration. It can also control IEEE 488 devices from anywhere on an Ethernet‑based (LAN) TCP/IP network (Gigabit, 100BASE‑TX, 10BASE‑T). Each device interfaces to and shares up to 14 GPIB devices from several network hosts, and you can control up to 100 GPIB‑ENET/1000 interfaces with a single computer. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
Hot Torsion Mobile Conversion Unit
-
Capable of applying torque up to 100 Nm (50 Nm standard configuration), Hot Torsion Systems from Dynamic Systems are the first commercially available torsion systems to incorporate direct resistance heating.
-
Product
MX Series - i2 Modular Inserts
-
VPC i2 MX inserts offer standard and hybrid transmission options for both wired and PCB solutions.
-
Product
VLF Testing and Diagnostics Unit
Viola TD
-
Cable testing and diagnostics with the BAUR viola TD. The portable and high performance high-voltage testing and diagnostics device is available in two different configurations:viola: Used for cable and cable sheath testing of electrical equipment and medium-voltage cables up to 35 kV. Another function is insulation testing on electrical equipment. viola TD: Expands the functional scope of viola with the tan delta diagnostics and Monitored Withstand Test (MWT) that combines the cable testing and dissipation factor measurement. This allows for an accurate and comprehensive assessment of the cable condition.* Cable testing and dissiation factor diagnostics in one device* High performance and compact* Easy and quick test setup* Automatic testing and diagnostic sequences
-
Product
Energy Measuring Units
-
Mitsubishi Electric Automation, Inc
Energy measuring units to support energy saving at workplaces.These units support to monitor consumption energy precisely, which is necessary for reducing energy cost. By combining with Split-type current sensor, you can easily fix in equipments which you want to measure.
-
Product
Front Panels for Plug-In-Units | IEC
-
Front panels for plug-in-units according to IEC | with or without EMC protection | aluminum 2.5 mm | clear anodised
-
Product
Control Unit
MX 256
-
Teledyne Gas & Flame Detection
The MX 256 is a digital control unit intended for the detection and measurement of gases present in the atmosphere and more generally for the processing of any digital signal from digital sensors (OLCT 10N types), relay module, analog output module, logic input module. Thanks to its new option, an industrial controller module or remote HMI, it is possible to add analog input modules for sensor-transmitter connection (4-20 mA) and / or relay modules, this allows to not only extend the capacities but also to have event recordings (Location, Alarms,.....) and to have access to the data via the embedded web page.
-
Product
Railway Motion Control Unit
RMCU
-
The Railway Motion Control Unit – RMCU is a high-performance strapdown system developed for Railway applications to determine the absolute orientation (Heading, Pitch, and Roll) and motion parameters (Angular Rates and Linear Accelerations) for any Railway Platforms on which it is mounted. Orientation is determined with high accuracy for both motionless and dynamic applications.
-
Product
Visual Fault Locator
FFL-210-U
-
FFL-210-U Visual Fault Locator is equipped with a 650 nm high power visible laser diode,can be operated in CW (continuous) or MOD (1Hz modulation) mode. There are two LED indicators：RED & GREEN; the RED one shows the operating mode of the Laser Diode output signal, and the GREEN one indicates low battery level. FFL-210-U is housed in a pocket-size, rugged metal casing, comes with a carrying pouch.
-
Product
Motorised Clemen Unit
3000
-
The Elcometer 3000 Motorised Clemen Unit is a robust and accurate instrument for evaluating the resistance to scratching of a coated surface. The sample can be metal, wood, glass, plastic or other hard materials.
-
Product
Unit Testing Mocking Solution for .NET
Coverage
-
Isolator displays your code coverage instantly in your editor while you code, which means you can spot uncovered areas while the code is fresh in your mind.
-
Product
High Power Fiber Optic Visual Fault Locator
VFL-700
-
Shanghai Fibretool Technology Co.,Ltd.
The VFL-700 is specially designed for field personnel who need an efficient and economical tool for fiber tracing, fiber routing and continuity checking in an optical network during and after installation.
-
Product
Detection of PtG and PtP Faults in Line Networks
LineTroll 110Tμr
-
The indicator is powered by replaceable long-life lithium batteries which have a life expectancy of 10-15 years. It provides a 360 degree visibility for indication both for transient faults and permanent faults.
-
Product
Attenuation Control Unit, DC to 6 GHz, 0 to 121 dB, 1-dB Steps
J7201A
Attenuator
Designed for WLAN and WiMAX™ device manufacturing test and mobile handset base transceiver station (BTS) handover test.
-
Product
Releaseit Shallow Water Deck Unit
-
Teledyne Benthos’ new Releaseit Deck Unit and dunking transducer enables communications and acoustic release functionality when used with any of Teledyne Benthos’ R-Series Acoustic releases deployed in shallow water environments. Designed with Teledyne Benthos’ proven engineering and reliability, Releaseit is a value-priced alternative deck unit allowing for basic coastal operations. When paired with our new R500 Shallow Water Acoustic Release, the combined system represents a lower-cost turn-key option for shallow water applications up to 500 m water depth.
-
Product
Control Unit
EC-501A & EC-501A(G)
-
Dynatrol® EC-501A and EC-501A(G) Control Unit combines with the DJ and G Series Dynatrol® Level Detectors, including Sealed and Suspended units. Within the Control Units, a SPDT relay is operated from the On/Off signal of the Dynatrol® Level Detector. Simply actuate process control equipment, level alarms or indicator lights from the contacts of this control unit.
-
Product
Adapter Rails (for High Speed Inserts), i2MX, ITA, 88 Pos, 11 Slot
510144001
Adapter Rails
Allows use of SIM inserts in i2MX ITA. Accommodates 11 single-slot inserts.
-
Product
Emergency Power Supply Unit (EPSU) (8) 5-15R 1U/0U V/H
EPS-815-HV
-
EPSU Power (Basic / Surge / Metered / Value) – rack mountable power distribution, 120V, optional surge suppression, and amp meter
-
Product
High Power, Low PIM Switch Unit
LPSU series
-
LPSU series high power, low PIM switch units combine 65 low PIM ports or 14 low PIM ports. These switch matrices are designed in testing situations that require multi-band PIM sources, components or antennas. Combinations of multi-band PIMtesting are now easily possible, improving workflow significantly. LPSUs can be integrated in existing production control systems. Frequency range 698-2700 MHz.
-
Product
Signal, Patchcord, ITA, 36", QuadraPaddle Insert, 36", Single Ended
7-151924000-036
Signal Patchcord
Signal, Patchcord, ITA, 36", QuadraPaddle Insert, 36", Single Ended
