Simulators
create what could be.
See Also: Simulation, Simulation Software, Simulation Testing, Emulators
-
Product
Portable Vibration Calibrator
AT-2040
-
With AT-2040 you will find the features required for your application without having to install cumbersome and expensive addons. AT-2040 features a full-automatic sensitivity test mode, sensor simulation, power supply output for sensors that require voltage such as the 7310 and 991V aviation sensors, a built-in sensor charge amplifier for both single-ended and differential charge accelerometers, and a custom sensor input that can be configured to fit most accelerometers with a one to one cable.
-
Product
PCI Precision Resistor Card 9-Channel, 1.5Ω To 6.97kΩ
50-297-024
-
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Solar Simulator for Multijunction Solar Cells
-
For series connected multijunction cells, at a given spectrum (e.g. AM 1.5 or AM 0 for space solar cells), one of the cells will limit the current in the series connection of cells. All solar simulators deviate from the true AM 1.5 spectrum, and they are only classified in wide spectral bands (100nm width). So even for class A or A+ solar simulators, it can easily happen that the bandgaps of the multijunction cells are such distributed that the 'wrong' cell will limit the current, if a solar simulator with fixed spectrum is used. In the 70s and 80s, when these measurements were first developed, intercomparisons showed deviations of cell efficiency in fixed spectrum solar simulators of more than 40%.
-
Product
UDP Test Tool, Flood Generator, VoIP Readiness Test Tool
-
The Multiprotocol Network Tester is a freeware, open source tool which enables you to measure quality of your IP network. It can also be used to generate UDP flood or to simulate UDP DoS attack. SIP call is usually established using a SIP session with a bidirectional RTP stream. SIP and RTP protocols are based on UDP transport protocol. UDP uses a simple transmission model without implicit reliability, ordering and data integrity. Each single UDP packet is transferred independently. The quality of a SIP call depends on delays and loss of IP packets in a network. Long delays lead to large RTP jitter and bad sound quality of a SIP call.
-
Product
Express Card
EXC-1553ExCard/Px
-
Each channel of the EXC-1553ExCard/Px operates simultaneously as a Bus Controller and/or multiple (up to 32) Remote Terminals, or as a Triggerable Bus Monitor. The card supports error injection and detection. The card’s small size and compatibility with notebook computers make it the perfect solution for performing system simulation of the MIL-STD-1553 bus, in the lab and in the field.
-
Product
PXI Resistor Module 4-Channel 1R to 510R with SPDT
40-293-114
-
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI Resistor Card 2-Channel 2 Ohm To 131k Ohm
50-293-034
-
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI Resistor Module 4-Channel 1R to 255R with SPDT
40-293-113
-
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Loading Devices
-
Educated Design & Development, Inc.
Sometimes you may need additional loading for abnormal testing (i.e. overload test). Other times, you may need additional loading to simulate worst case normal operation conditions (i.e. input test, temperature test). No matter what your application, we have the loading device to fit your needs! TECH NOTE: Be sure to request our outline titled "Selecting Loads" for assistance in determining the proper rated device for your application.
-
Product
Panel-mounted Power Amplifier(Hardware In The Loop Simulation)
PA30Bi
-
PA30Bi is the panel-mounted type real time simulation amplifier with three-phase current and four-phase voltage.
-
Product
Analog Output Device
-
The Analog Output Device helps you create applications such as stimulus-response, power supply control, deterministic control, and sensor/signal simulation. The Analog Output Device supports various output resolutions, channel counts, and other onboard features, so you can replace several kinds of instruments in your system, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators.The Analog Output Device includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
Graphical Debugging for Verilog, VHDL, and C++ Simulators
BugHunter Pro
-
BugHunter uses the SynaptiCAD graphical environment and supports all major HDL simulators. It has the ability to launch the simulator, provide single step debugging, unit-level test bench generation, streaming of waveform data, project management, and a hierarchy tree. The unit-level test bench generation is unique in that it lets the user draw stimulus waveforms and then generates the stimulus model and wrapper code and launches the code. It is one of the fastest ways to test a model and make sure that everything is working correctly. The debugger also has exceptional support for VCD waveform files.
-
Product
PXI Programmable Resistor Card 2-Channel 2.5 Ohm to 8.19k Ohm - SPST
40-294-124
-
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Stability Test Chamber
-
Wewon Environmental Chambers Co, Ltd.
Test Instrument to simulate effects of weathering conditions, e.g. UV light exposure and water exposure, on samples to conveniently predict the relative durability of a sample, e.g. paint, surface coatings, plastic and related materials.
-
Product
PXI Precision Resistor Module 4-Channel, 2 to 102k
40-297-134
-
This 4-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Power ICs - MicroBUCK® - Voltage Regulator
-
*Highly integrated microBUCK POL solutions deliver high efficiency while reducing costs*Each family offers a large portfolio of high density parts with common pinouts, allowing designers to scale for the best combination of cost and performance*Our PowerCAD simulation tool allows users to select the appropriate microBUCK regulator and generate a full circuit schematic**For performance optimization and comparison purposes, the schematic can then be edited as required.**Once the basic circuit is created, the user can perform DC, transient, and start-up simulations with visibility of all the circuit node waveforms.**Following these steps, the PowerCAD 2.0 simulation tool generates a bill of materials (BOM) available for online ordering.
-
Product
Channel Emulator
-
Qosmotec Software Solutions GmbH
Knowledge about channel models is not necessary to run tests with the QPER Channel Emulator. It applies the visualised virtual drive test concept, which is also used in the handover tester, to a fully fledged channel emulator: The tester outlines the network layout on the screen and defines a drive test route on the map. While running a simulated drive test, all channel effects are automatically calculated by QPER and applied to the channel emulation hardware.
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel With V/I Readback
41-752A-013
-
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Digital Load Cell Simulator
Model EL41
-
Xiamen Elane Electronics Company, Ltd
Detection and debugging of all kinds of weighing instruments - "must have" for any scale service technician - fully RS232 controllable for testing of electronics for scale installation and manufacturing.
-
Product
Electromagnetic Environment Simulators
A2PATS® Products
-
Our A2PATS Family of Products are electromagnetic environment simulators built upon Textron Systems' open-architecture direct digital synthesizer technology, coupled with our proven user interface. Our easily programmable, plug-and-play modular architecture uses identical, phase-coherent, direct digital Synthetic Stimulus Instruments (SSIs) as the radio frequency (RF) source for all signals. These modular commercial RF Sources are easily configured in our commercial cabinets. Four standard configurations are available including single-cabinet, multi-cabinet, mini-A2PATS, and A2DSG™.The A2PATS Family consists of numerous commercial products including but not limited to A2PATS, A2DRI™, A2DSG and A2EOSTIM.
-
Product
PXI Resistor Module 2-Channel 1.5R to 8.19k with SPDT
40-293-124
-
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
TopSpice 10
-
TopSpice is an affordable integrated computer-aided circuit design software package offering advanced native mixed-mode mixed-signal analog/digital/behavioral simulation based on the industry standard SPICE simulator program.
-
Product
Charger / Quick Charger / Adapter / LED Driver Test System
6010
-
6010 Charger / Quick Charger / Adapter / LED Driver Test System is able to meet multi-types power products test requirements，and its multi-U.U.T test simultaneously capability can significantly enhance the production line throughput. It also possess multi-modular combination that includes low noise analog AC source with Triac to simulate output, four sets precision power meter, two or four sets ripple noise / timing measurement module, four sets OVP DC power supply, 3310F series & 3332F/3336F Electronic Load module and unique design 3340F series for LED power driver output test.
-
Product
Solar Stimulators
-
Alpha-Omega Power Technologies, LLC.
Alpha-Omega Power Technologies (AOPT) has developed a line of pulsed concentrator photovoltaic (CPV) solar simulators based in its experience with pulsed high voltage flash lamp systems and its patented high speed, high power load.
-
Product
Towing Dynamoters
-
From light passenger cars to heavy commercial truck vehicles, you can turn to us for a solution that saves you time and money by easily and reliably measuring attributes under a range of simulated load conditions, negative slopes and positive slopes up to 25% – all in a safe, controlled environment. Look to Taylor as the industry leader for a record of pioneering valuable towing dynamometer (dyno) advancements including:
-
Product
Test House Services
-
At TS-Space Systems we have over 30 years experience in designing, building and operating vacuum systems for space simulation and materials testing. We have three in-house thermal vacuum chambers which are configurable for a range of temperatures for either monitored vacuum bakeout or thermal vacuum cycling. We design, build and operate these systems in-house which means we are more flexible than most test houses and are happy to modify feedthroughs, manufacture additional support equipment and even change the operation of the chambers, where possible, in order to accomodate customer requirements.
-
Product
8 Port Phone Line Simulator (FXS) Adv
CH-8FXS-A
-
This unit has 8 analog phone lines (FXS) making it a perfect tool for testing VoIP gateways, IVR, modems, access servers, audio conference equipment or anything that requires phone lines. Telephone line simulator acts like a "telephone company in a box" providing dial tone, ring voltage and all advanced phone line features such Caller ID, Call Waiting, Call Hold, Three Way Calling and many others.
-
Product
Mid-Range Fiber Stretcher
PZ3
-
The PZ3 is the mid-range member of our family of fiber stretchers. It is a fiber wound piezoelectric element for use in a wide range of optical interferometric measurement and sensing system applications. Typical uses include open loop demodulation, sensor simulation, variable optical delay, general purpose fiber interferometry and large angle modulation of interferometric phase.
-
Product
Compact PCI Bus Analyzer / Exerciser
CPCI650
-
The CPCI650 analyzer provides a multitude of functions to help you analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation and fault generation- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics
-
Product
UV Accelerated Weathering Testers
-
Dongguan Amade Instruments Technology Co., Ltd
UV accelerated weather tester is also well known as UV test chamber, which is a type of environmental test chamber using fluorescent UV as light source to determine the resistance of plastics, leathers, rubbers, fabrics and so on to weathering under the specified conditions. We know that Ultraviolet light only accounts for 7% of the total sunlight, but it plays a core role in deterioration of materials. Not only does the ultraviolet, but UV test machine also can simulate dewing, high temperature, high humidity, black environment to be reappeared as a circulation. So UV weathering test is an essential measure for people to research and know the degradation state of specimens in advance as the time goes on.
