Simulators
create what could be.
See Also: Simulation, Simulation Software, Simulation Testing, Emulators
-
Product
PXI-2512, 7-Channel, 10 A PXI Signal Insertion Switch Module
778572-12
-
7-Channel, 10 A PXI Signal Insertion Switch Module—The PXI‑2512 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2512 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
-
Product
Lithium Battery Test Chambers
-
Dongguan Amade Instruments Technology Co., Ltd
Lithium battery test chambers are used to simulate various extreme conditions such as crush, impact, penetration, overcharge etc the lithium ion cells and batteries are subjected to during use, transportation, storage and disposal to determine the safety performances, tests including altitude simulation test, thermal test, vibration test, shock test, external short circuit test, impact/crush test, overcharge test, discharge test etc based on UN38.3, IEC62133, UL1642 standards. Applicable to communication products, computer products, consumer electronics, automobile power supplies and so on.
-
Product
2 PRI + 4 Port FXS PSTN Simulator Adv
CH-4FXS-MOD-2PRI-A
-
One of the most feature rich PSTN simulator on the market. Unit has 4 analog phone lines (FXS) making it a perfect tool for testing VoIP gateways, IVR, V.90 modems, RAS servers, audio conference bridges or anything that requires analog phone lines. 2 port T1/E1/PRI module provides non-blocking switching among FXS ports and any of T1/E1/PRI B-channels or Time slots.
-
Product
AIT PXI Express Test & Simulation Instruments
-
Avionics Interface Technologies
AIT’s Test & Simulation Instruments for MIL-STD-1553, ARINC 429, ARINC 664/Avionics Ethernet, and Fibre Channel are available in PXI and PXI Express form factors and are supported by software drivers for Windows, Linux, and LabVIEW Real Time. All instruments are also supported by Software Development Kits which provide API’s for C/C++, C#, and LabVIEW.
-
Product
PXI/PXIe High Density Precision Resistor Module, 9-Channel
40-297A-023
-
The 40-297A-023 (PXI) and the 42-297A-023 (PXIe) are 9-channel programmable resistors with a range of 1.5 Ω to 3.55 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
UXG X-Series Agile Vector Adapter, 50 MHz to 20 GHzNEW!
N5194A
-
The N5194A is part of the UXG family of signal generation products designed for threat simulation; simulate complex signal environments for radar/EW.
-
Product
Dropout, Surge, Ripple Simulator and AC/DC Voltage Source
DSR 100 Series
-
DSR 100 Series systems provide complete, single-box solutions for immunity testing. They include a simple-to-use yet powerful standards waveform generator matched with an industry leading power supply technology and come with an extensive library of tests for many automotive and aviation standards.
-
Product
Connect
-
Amplify the benefit of simulation throughout product development. To bring complex products to market faster. Ansys Connect is a toolset for creating the simulation digital thread. This links simulation to the processes, tools, and data used across product development. Amplifying the benefit of your physics solver by running more simulations for more users, helping bring more complex products to market faster.
-
Product
Upset Testing Machine
YQ/YQR Series
-
Jinan Testing Equipment IE Corporation
The series of upset testing machine are designed according to the International Standard 'Metallic Materials Upset Test Methods', especially for the quality inspection of high-speed rods and wires. Through simulating the quick impact conditions of the metallic materials during the upset and pressing, the machine truthfully reflects the instances of the quickly compressed rods and wires. Under room temperature or hot conditions, exert test force in the direction of specimen axial line, quickly compress the specimen, and then the machine can inspect the metal ability of bearing upset deformation in the specified upset ratio. The upset testing machine can also show the metal’s surface disfigurements. The upset testing machine is widely used in the steel industry, standard specimen manufacturing industry, and tools manufactures for inspecting the upset tests of metallic materials.
-
Product
Multi-Standard Local Loop Simulatorw/Optional AWGN Generator
458-LM-A1-30
-
FEATURES: Simulates 26 AWG PIC as specified in ANSI T1.417; Bandwidth DC to 30 MHz; Solution for ADSL, ADSL2, ADSL2+, & VDSL2 chip/modem/DSLAM testing;
-
Product
Machine Tool Probes and Software
-
Probing is an established best practice for maximising the efficiency, quality, capability and accuracy of machine tools. Standard routines built into modern CNC controls simplify the integration of probing cycles into machining operations and offline tools. These routines, combined with a CAD interface, make the simulation of measurement functions easy.
-
Product
IEC60695 Needle Flame Test Machine
CX-Z18
-
Shenzhen Chuangxin Instruments Co., Ltd.
Needle Flame Tester is made according to Standard IEC60695 and GB5169, meanwhile it’s a synthesis test equipment that can meet related standard requirements. It’s mainly used to simulate technical evaluation interior equipment. It’s applied to the risk of ignition test of electrotechnical equipment, parts and elements, also suitable for the risk of ignition test of solid electrical insulating materials or other combustible material.
-
Product
AWD Dynamometers
-
Full time AWD vehicles are designed to provide maximum performance regardless of road conditions. In cases where traction is less than ideal, a vehicle may be designed to improve stability and traction at the expense of power. This means adding torque to a spinning wheel or retarding of timing. In order to properly test an AWD vehicle for peak performance, an AWD chassis dynamometer must be able to simulate ideal road-load conditions to the vehicle. This approach allows the vehicle to be evaluated under "optimum" operational conditions; whereby torque is distributed to the vehicle's tires in the same manner that would normally occur when a vehicle has equal traction at all four drive wheels, and is therefore operating at peak efficiency.
-
Product
4 Port T1/E1/PRI ISDN Simulator
SIM-4PRI
-
The most inexpensive ISDN simulator on the market. This unit has four PRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network.
-
Product
MIMIC® IPMI Simulator
-
The MIMIC IPMI Simulator, the industry’s first integrated simulation tool supporting IPMI, allows developers to perform real world, integrated device simulations. MIMIC simulates IPMI-capable high-end server systems. MIMIC allows suppliers of IPMI devices and applications to design, develop and test their products in a virtual and scalable network environment, assuring customers that their applications will work properly when deployed across heterogeneous environments.
-
Product
API Testing with LoadView
-
Simulate 1,000s of users hitting your API every second to generate 100,000+ calls to your server per load testing session.Define your API tests to simulate traffic at the pace you need by implementing a load curve that increases the number of simultaneous users as necessary to properly test your system.Gather performance metrics consisting of the response times of each session and validation that the API returns the expected results in each response.Visualize how the average response time is affected as you increase the number of simultaneous users.Examine individual test sessions to see error codes and utilize additional troubleshooting tools such as traceroutes, waterfall charts and a copy of the server response.
-
Product
2 Port 4GFC Fibre Channel ARINC818 Test, Simulator and Monitor Module For PCIe
APS-FC-2
-
The APS-FC-2 is AIM’s high performance PCIe module offering 2 ports with full function test, simulation, monitoring and analyzer functions for Fibre Channel networks. The APS-FC-2 is a powerful State-of-the-Art 4-lane PCIe 2.0 compliant PCIe board.
-
Product
Test Engines
-
Verified Systems International GMBH
The test system cluster architecture is based on dual CPU or 4-CPU PCs acting as cluster nodes. The nodes communicate and synchronise over a high-speed network (Myrinet or InfiniBand). A modification of the Linux operating system allows to run the test execution and evaluation algorithms in hard real-time on reserved CPUs, where scheduling is non-preemptive and controlled by the test system itself. The interrupts caused by interfaces to the system under test may be relayed to CPUs designated explicitly for their handling. This approach offers the opportunity to utilise high-performance standard hardware and the services provided by the widely accepted Linux operating system in combination with all mechanisms required for hard real-time computing. The cluster architecture presents an opportunity to distribute interfaces with high data throughput on different nodes, so that PCI bus overload can be avoided. In addition, the CPU load can be balanced by allocating test data generators, environment simulations and checkers for the behaviour of the system under test ("test oracles") on dedicated CPUs.
-
Product
Temperature, Humidity And Others Relevant Environment Tester
-
King Design Industrial Co., Ltd.
Allows your product quality and reliability tests more realistic toward actual environment; simulate the actual environment in the temperature, humidity and vibration by separated of combined tests. The tester is equipped with control panel, Chinese-English display and micro-computer temperature control system; applicable to aerospace, military, vehicles, electronics and other high-tech products.
-
Product
Simulation Systems
-
Bloomy offers Simulation Systems for Hardware in-the-Loop (HIL) and open loop test of electronic controls and mechanical actuators for all types of transportation and defense systems including aircraft, rail, automobiles and ships. These systems, now deployed at major aerospace, locomotive and military manufacturers and research facilities worldwide, provide world-class, high-fidelity simulated environments for use in both closed-loop and open-loop testing. Because Bloomy’s Simulation Systems are largely constructed from COTS components, time to first test can be reduced significantly, and their highly-customizable nature allows your test system experts to provide your unique IP to differentiate your product from your competitors.
-
Product
Solar Cell Testers
-
Solar Cell Testers are integrated systems incorporating Solar Simulator and I-V Measurement systems. PET offers Standard and Advance IV Measurement software. PET Cell Testers are capable of measuring a diverse range of solar cell parameters such as Isc,Voc, Imax,Vmax, Pmax, FF, Rsh, Rs and η cell conversion efficiency, complete light and dark I-V curves. All that needs to be done to test a cell is to load the cell, make electrical probes contact and press “Measure” icon on the I-V Measurement System software. The software will automatically open the Solar Simulator shutter, perform the test and close the shutter after the test is complete. The design is modular in nature and can be easily upgraded. Some options can added at a later time.
-
Product
Mobile Test Systems
-
The systems include A+A+A+ LED solar simulators, high-resolution electroluminescence testers and various other tests that you can easily integrate into your transport of choice or directly into a container on site.
-
Product
Fibre Channel Test & Simulation Interface for PCI-X
PCI-X-FC4
-
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
Product
Universal Test System
LS6601A
-
LS6601A Universal Test System is based on LXI bus, primarily used for functional electronic product or system verification, test parameters. Because the system design is based on LXI bus structure, so its addition to general characteristics of versatility, scalability, but the architecture of the system more flexible, the test system is not limited to one or more cabinets, but may be needed test network and multiple LS6601A and can be easily grouped into one or more of the ground test system, depending on the test mechanism, form a powerful set of test, control, simulation, simulation, data management as one; distributed in different places .
-
Product
PXI/PXIe High Density Precision Resistor Module, 9-Channel
40-297A-113
-
The 40-297A-113 (PXI) and the 42-297A-113 (PXIe) are 9-channel programmable resistors with a range of 1 Ω to 238 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
2-CH MIL-STD-1553A/B Bus Simulator Module
1553 WA73A-455
-
The WA73A-455 MIL-STD-1553A/B Bus Simulator Module allows a system controller in an ATE system to communicate with and test devices that conform to the MIL-STD1553A/B data bus used in military aircraft and communications systems. Each of the WA73A-455's two channels operate as two separate and independent channels with their own VXIbus logical address, interrupts, and complete set of controls and indicators. As a result, each channel of the WA73A-455 is truly an independent instrument, and, therefore, individually programmable.
-
Product
PCI / PMC / CompactPCI Test System
PCITS
-
The CPCI850 analyzer provides a multitude of functions to help you analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation- Target memory with addressable windows- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics- Compliance testing
-
Product
2 PRI + 16 BRI-U ISDN Simulator
CH-16BRI-U-MOD-2PRI
-
This unit has two PRI ports and 16 BRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network
-
Product
Communication Data Logger
LE-270AR
-
LE-270AR is an Analyzer and Communication Data Logger of CAN/LIN. It has logger mode with which you can records CAN/LIN communication logs in the SD/SDHC card for long hours and remote mode with which you can monitor data at real time by connecting the analyzer with PC. It also has simulation mode with which you can repeatedly transmit CAN/LIN data which is registered in advance and selected on the PC. You can measure 2 channels of CAN/LIN communication lines and can simultaneously register voltage data of 4 external signals.Its power failure protection, waterproof, and low power consumption widens the usage of analyzer such as in the automation factories and other production factories.
-
Product
PXI Precision Resistor Module 18-Channel, 1 to 470
40-297-014
-
This 18-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
