-
Product
Flatness, Bow, Warp, Curvature, Glass Thickness
FLATSCAN 650 3D
-
Optik Elektronik Gerätetechnik GmbH
High accurate flatness & thickness measuring system for large substrates.
-
Product
Flatness Mirror
10773A
Optical Module
The Keysight 10773A Flatness Mirror is a 100% reflectance mirror that turns the direction of an incoming laser beam 90 degrees. The mirror, used in the 5530 Laser Calibration System, measures flatness in applications such as surface plate calibration. It can be used in place of the 10707A Beam Bender (6 mm or less beam diameter) for applications that require the larger aperture of the 10773A.
-
Product
Flatness, Bow, Warp, Curvature, Glass Thickness + Optics Test Equipment
Mobile Wedge Angle Sensor WAS 160
-
Optik Elektronik Gerätetechnik GmbH
Portable sensor for measurement of radius and wedge angle. Application: windshields of cars, helicopters, airplanes.
-
Product
Measurement Of Straightness, Flatness, Positioning Uncertainty Of Round Tables
ELCOLEVEL - Software For 3D-straightness Measurement
-
Optik Elektronik Gerätetechnik GmbH
ELCOLEVEL is a software with interfaces to electronic autocollimators and inclination levels of different manufactureres. This allows for example the 3D-Straightness measurement (twist-, roll- and yaw-angle) of slides in one and the same measuring procedure.
-
Product
Mask Flatness Measurement System
Tropel® UltraFlatTM 200 Mask System
-
The Tropel® UltraFlatTM 200 Mask System was designed specifically for the photomask industry. It delivers the lowest measurement uncertainty for ever-tightening mask flatness specifications. Shrinking device features require not only flatter wafers, but flatter masks.
-
Product
Measurement Of Straightness, Flatness, Positioning Uncertainty Of Round Tables >
ELCOWIN - Software For 2D-straightness Measurement With Electronic Autocollimators
-
Optik Elektronik Gerätetechnik GmbH
The software ELCOWIN serves for the measurement of straightness, squareness, parallelism of slides and flatness of precision tables by the autocollimation principle. ELCOWIN can be used in connection with electronic autocollimators of the ELCOMAT series from Moeller-Wedel-Optical.
-
Product
Non-contact Inline Sheet Resistance Measurement Module For Flat Panel Display
NC-600
-
*Non-stop and non-contact sheet resistance measuring of thin film on glass runs through on conveyer*1 to 10 number of probe by sizes of glass is attachable*Glass collision prevention function*Continuous test data report to the host computer
-
Product
Whiteness Meter
-
Guangzhou Amittari Instruments Co.Ltd
AMITTARI l Whiteness Meter is mainly used to directly measure the whiteness value of object or powder with flat surface. It can be widely used in whiteness measurement of textile printing and dyeing, paint, chemical building materials, paper board, plastic products, white cement, ceramics, enamel, talc powder, starch, flour, salt, detergent, cosmetics and other substances. The instrument pass strict inspection and testing, conforms to the JJG 512-2002 Whiteness Meter Verification Regulation. Also conforms to GB3978、GB3979、GB7973、GB7974、ISO2470、GB8904.2、QB1840、GB2913、GB13025.2、GB1543、ISO2471、GB10339、GB5950、GB12911、GB2409 and other standards.
-
Product
Roller Contact Sensors
-
Electronic Development Labs, Inc.
EDL’s roller contact sensors are expertly crafted to provide exceptional measurements on both moving flat and rotating cylindrical surfaces, along with stationary objects.
-
Product
SMART III RF Probe
-
Finna Sensors’ Smart III RF Moisture Probe is appropriate in those situations where NIR use on conveying systems/web applications or RF flat plate sensor use on board type products are not sufficient. Examples include tanks, bins, barrels, drums, Super Sacks™, silos, etc. These applications require a probe type moisture meter where the probe is inserted into, and is surrounded by product. Since the probe generates a 3 inch diameter radio frequency field around the length of the probe, a significant volume of product is measured. As the product is slowly removed from the silo, and refilled from the top, it passes by the RF Probe, thereby providing a constant real time moisture measurement. Typical applications would include starches, distillers and brewers grains, granulated chemicals or food ingredients, whole grains such as corn kernels, rice, soybeans, tree nut stockpiles, etc.
-
Product
Franklin Tester
Model 717
-
The Model 717 Franklin Tester provides a means of testing single strips or punchings of flat rolled electrical steel, for surface insulation resistance under predetermined conditions of voltage and pressure.
-
Product
LED 4 Flat Tester
48655
-
Hopkins Manufacturing Corporation
Quickly and easily confirm if your vehicle 4 flat connector wiring is properly installed and functional. Fits on your keychain to keep it handy! LEDs test left/right turn, brake and taillight.
-
Product
2-26.5 GHz Traveling Wave Amplifier
1GG7-8045
Amplifier
The 1GG7-8045 is a broadband GaAs MMIC Traveling Wave Amplifier designed for high output power and moderate gain over the full 2 to 26.5 GHz frequency range. Seven MESFET cascode stages provide a flat gain response, making the 1GG7-8045 an ideal wideband power block. Ebeam lithography is used to produce gate lengths of ~0.3 mm. The 1GG7-8045 incorporates advanced MBE technology, TiPtAu gate metallization, silicon nitride passivation, and polyimide for scratch protection.
-
Product
Cable Management Tools and Testers
-
For anything compture repair and workstation installation tool, you've come to the right place. C2G carries a variety of cable tools and testers for network, coaxial, electrical, F-type, PC, telephone, and fiber cables. Our crimp tools are also available for RCA, BNC, F-type, RJ45, RJ11, RJ12, and flat ribbon connectors. C2G cable cutting tools can be used to cut a range of wiring types, from RG6 and RG59 coax, speaker wire, UTP network cable, flat ribbon, and more.
-
Product
Flexible x1 PCI Express Riser
SKU-039-XX
-
The Flexible x1 PCI Express Riser (Riser) was designed to extend the x1 PCI Express bus. The Riser includes an x1 PCI Express adapter board (optional: x4 PCI Express adapter), x1 PCI Express host board and a 12” PCI Express Flat cable.
-
Product
Preamplifier, 100 MHz to 18 GHz
87405C
Amplifier
Exceptional gain (25 dB) and flatness (1.5 dB) combined with a probe-power bias connection which eliminates the need for an additional DC power supply, makes these preamplifiers the ideal choice for spectrum analyzer or stand alone applications.
-
Product
Laser Head
5517D
-
The Keysight 5517D is used primarily in VME and PC based laser interferometer systems where the velocity of motion is faster, such as semiconductor lithography and flat panel applications. Please contact Keysight for custom requirements.
-
Product
Advanced Hydraulic Wedge Action Grips
2742 and 2743 Series
-
The Instron advanced hydraulic wedge action grips deliver controlled, constant gripping force using an external hydraulic supply across static and dynamic testing. They support capacities up to 600 kN (static) and 500 kN (dynamic), with interchangeable jaw faces for round or flat specimens. The design ensures jaw face positions remain fixed during gripping (eliminating preload), compensates for changes in specimen thickness, and is ideally suited for use with metals, composites, and plastics.
-
Product
L-Band Red/Blue-Band Pass MWDM
WD1616/R, WD1616/B
-
Hangzhou Huatai Optic Tech. Co., Ltd.
WD1616/R, WD1616/B is based on mature thin film filtering tech, with wide bandwidth, flatness, low insertion loss and high isolation. It is mainly applied to the combination and separation of L-Band, Red-Band (1589~1603nm) and Blue-Band (1570~1584nm).
-
Product
Low Cost Microwave Wideband PIN Preamp Receivers
MR21 (40KHz~18GHz)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
MR21 series microwave wideband optical receiver, adopts High linear PIN diode and Low noise pre-amplifier IC, within bandwidth of 40KHz~18GHz, they are featured with excellent linearity, high responsibility and superior flatness of the RF response in both, power and phase. They provide an outstanding linearity fiber optical communication for analogue wideband microwave application. Due to avoidance of using expensive coaxial cable or wave guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless, timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s and 18Gb/s high speed communication system.
-
Product
Flat Flex Test Fixtures
-
Z-AXIS Flex Circuit Test Fixtures are used to connect flex circuits to test equipment. 20,000 plus cycles. Using the Z-Axis Elastomeric Connector Interposer, the connection to the OEM FFC connector becomes permanent and is thereby saved from over-use.
-
Product
Horn Antenna
-
Horn antenna is a partial discharge sensor designed to receive electromagnetic (EM) emissions from a PD occurring in electric assets like GIS and GIL or MV and HV power transformers. It is a broadband antenna with a flat response which makes Horn antenna suitable in a number of different applications. It has been optimized to operate in a frequency range suitable for PD activity monitoring and it was designed to provide maximum sensitivity and high gain.
-
Product
Spectrally Flat Class B Albedometer
LPPYRA05
-
Albedometers are composed of two pyranometers that are mounted back-to-back. An albedometer measures in two directions; one pyranometer is facing upwards (measuring the global solar radiation), the other pyranometer is facing downwards (measuring the reflected solar radiation).
-
Product
Carrier Card
VIPC627-ET
-
VIPC627-ET is a 6U VME carrier card with four IP slots and extended temperature range. Two 50-pin, 0.1 inch flat ribbon cable connectors mounted in the front panel provide access to all IP I/O lines. Also, all I/O lines of 'IP D' are routed to VME P2 and 14 user selectable I/O lines of 'IP C' can be routed to VME P2 via a jumper field.
-
Product
8 GHz Differential Probe with ProLink Interface
DH08-PL
-
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
Shielded and Unshielded Cable
-
Teledyne Marine Cable Solutions
Shielding Types• Braided I Served I Spiral• Foil & Hybrid• Vapor Barriers• Copper & Alloys• Conductive & Static Dissipative Tapes• Conductive Fabrics• Tensile Members• RFI & EMI Tapes & Braids (Serveor Interwoven)• Utilizing Flat & Round Copper• Stainless Steel• Bronze• Aramid Fibers & Textile, amongothersConstruction• Multi-conductor, shielded pairs, pairs with steel tubed fiber or copper conductors with fiber optics, coaxial conductors & aramid strength fibers
-
Product
Power Detector Laser Power Meters
11PMK-H5
-
Fast, Small Size, Flat Spectral Response, Full NIST-Traceability, High Damage Threshold: 36 kW/cm² to 45 kW/cm², Personal Wavelength Correction™, Low profile, Air and Water cooled, Energy mode, Effective aperture diameter 19 mm (area 2.84 cm²)
-
Product
(70×90×15mm) C-Band DWDM Full Function Booster EDFA Module
WBA4100-FM02
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai WBA4100-FM02 series used 70 x 90 x 15mm MSA compact package, is a digital control circuit of DWDM power amplifier function module. Products using the most excellent optical properties, electronic control technology and complete software function is most advanced, wide wavelength range, low noise, excellent gain flatness characteristics and transient characteristics. Application for C-Band 44 wave or the 88 wave of DWDM system.
-
Product
(100×130×19mm) C-Band DWDM Booster EDFA Module
WBA4100-FM04
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai WBA4100-FM04 series used 100 x 130 x 19mm compact package, is a digital control circuit of DWDM power amplifier function module. Products using the most excellent optical properties, electronic control technology and complete software function is most advanced, wide wavelength range, low noise, excellent gain flatness characteristics and transient characteristics. Application for C-Band 44 wave or the 88 wave of DWDM system.
-
Product
Automatic Pull-Off Adhesion Gauge
510
-
Automatic hydraulic pump ensures smooth and continuous pressure application for consistent, repeatable adhesion strength resultsFully adjustable pull rates 0.1-1.4MPa/s (14.5-203psi) to meet National and International StandardsCan be used with 10,14.2, 20 and 50mm diameter dolliesUser definable limits with unique pressure hold and release functionUser definable measurement range with an accuracy of ±1% of full scale:10mm dolly: 100MPa (14400psi14.2mm dolly: 50MPa (7200psi)20mm dolly: 25 MPa (3600psi)50mm dolly: 4MPa (580psi)Dust and water resistant rugged design to IP64Interchangeable units: MPa, psi, Nmm2 and NA range of standard and thin substrate actuator skirts (compatible with Elcometer 506) available for adhesive strength testing on thick, thin, flat or convex substratesStore up to 60,000 readings with individual pull graphs in up to 2,500 alpha numerical batches, complete with attribute failure informationUSB and Bluetooth® data output - compatible with ElcoMaster® App for iPhone, iPod, iPad and Android mobile devices
