Product

Digital Multimeter with CE

-

ZHANGZHOU HUAYI ELECTRONICS CO.,LTD.

ZHANGZHOU HUAYI ELECTRONICS CO.,LTD.

A digital multimeter (DMM) is a test tool used to measure two or more electrical valuesprincipally voltage (volts), current (amps) and resistance (ohms). It is a standard diagnostic tool for technicians in the electrical/electronic industries. CE indicates that the product was designed and manufactured to mandatory European Safety and EMC/EMI requirements.

Product

Premium Automotive DMM

597

-

Electronic Specialties Inc.

597 - Electronic Specialties Inc.

*CATIII 1000 Volt / CATIV 600 Volt Approved & Safety Rated *Safe For Use on Hybrids and EV's *Highest Quality Auto-Ranging DMM Designed for Automotive Trouble Shooting *18 Test Functions, 48 Test Ranges *Peak Min/Max records transient voltages as fast as 1 millisecond *Min/Max Mode records variations in all functions *Also measures Temperature via Temp Probe in Both F and C *Milliseconds Pulse Width Measures Fuel Injector ON-TIME *Inductive RPM Readings for both DIS and Conventional Ignitions *Desirable 20 Amp Test Range - Dual Fuse Protection *Modern Design, the Protective Holster is Built Into the Housing *Data Hold, Auto Power-Off, + Trigger Adjust *Large LCD Display w/White LED Backlighting and 40 Segment Analog Bargraph *Blow Mold Case, Test Leads, K-Type Temp Probe, Inductive RPM Clamp and Instructions included *Waterproof to IP67 Standards

Product

Variable Power Supply

VS-10a

-

Allied Edison LLC

VS-10a - Allied Edison LLC

The VS-10a power supply is a light weight, portable, non-isolated “variable source” from 0 volts to 150 Vac or 0 volts to 150 Vdc and rated for up to 10 amps, thus the name VS-10a. It is comprised of an illuminated voltmeter that reads to the first significant digit, AC variable system output voltage, DC variable system output voltage, logic output voltage and one sense (continuity) contact monitoring points. Banana jacks for connection of test leads are spaced at intervals that allow the use of dual banana test plugs if desired. The VS-10a is protected by two levels of overcurrent protection; AC input, and ground fault protection by a GFCI. All circuitry is housed inside a custom designed case made from 16 gauge steel. An Internal fan dissipates heat buildup and exhaust through louvered side vents built into the case. The carrying handle is designed with a “spring return to rest” position and is padded for comfort. The case has been sized for optimum portability and is balanced from the handle during transportation. The case has a powder coated finish that is scratch, chemical and weather resistant. Rubber padded feet support the case when in the upright position and a convenience receptacle is located on the side of the case.

Product

Two Diode Assembly, P/N 6030C

-

Carl E. Holmes Company

Carl E. Holmes Company

Two Diode Assembly, P/N 6030CEach diode is rated for 400 Amps, 1200 PIVTwo diodes are installed on one heatsinkDimensions: 8”H x 8”W x 10”DEstimated weight: 20 lbs.When A is greater than B, Battery 2 is reversed BiasWhen B is greater than A, Battery 1 is reversed Bias

Product

PCB Test Fixtures

-

EverythingPCB

EverythingPCB

ATE, ICT, semiautomatic & manual electronic test fixtures, PCB test fixtures, cable test fixture, wiring harness test fixtures, dedicated test fixtures, functional test fixtures, electronic test fixture programming. PADS Schematic capture, circuit board layout, PCB design prototype, solder paste stencils, X-Y coordinate data, B.O.M. maintenance, and manufacturing documentation, Gerber data.

Product

48V / 250 Amp Load

BD15-48P-24/12

-

Manatronics Pty Ltd

BD15-48P-24/12 - Manatronics Pty Ltd

For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 12V, 24V and 48V Battery systems and is extremely cost effective.