Line Fault Indicators
See Also: Overhead Line
-
Product
Cable Fault Locator-TDR
TM800N
-
TM800N Cable Fault Locator (hereinafter to be referred as TM800N) is used for test est cable break, short circuit faults of telephone cable, data cable, high frequency cable, coaxial cable,and so on.
-
Product
Switch Indication Maintainer
The SIM
-
The SIM - Switch Indication Maintainer is a handheld device used to simulate normal switch correspondence while the switch is handthrown or handcranked to perform periodic maintenance or testing.
-
Product
Ferrite Indicator
-
The Ferrite Indicator is a simple, rugged, non-destructive inspection instrument developed for laboratory, shop and field use. The GO, NO-GO feature permits instant acceptance testing of austenitic stainless weld metals. The Indicator requires no external standards, no adjustments, no visual readings and is unaffected by position. It performs equally well on sheets, plates, rods, irregular shaped objects and individual parts of complex components. It is effective in locating areas of high or low Ferrite content heterogeneous products.
-
Product
Digital Fault Recording
SHERLOG
-
Fault recorder systems with a power quality analyser for comprehensively monitoring and assessing low, medium and high voltage networks in power plants and transformer substations. The measuring devices of the SHERLOG range make very high-resolution recordings of all the disturbances which occur in power supply systems. The behaviour of protection and switchgear devices during these system disturbances is recorded at the same time.
-
Product
Cable Fault Locator
TX2001
-
Lowest Cost Full Specification Professional Graphical TDR Rugged Palm Top Design 350g (12oz) 5 Measurement Ranges up to 3000m (10,000ft) 50, 75 & 100 ohm Selectable Impedance Built in Tone Generator for Pair Tracing & Identification Suitable for testing all Communications Cables Water & Dust Proof to IP54 Complete with tool-belt holster & test leads
-
Product
Acoustic Fault Detector
AFL212-AMD
-
K&S Engineering and Scientific Ltd
This compact acoustic headset, designed and manufactured by K&S Engineering and Scientific Ltd has been developed with state-of-the-art components to not only to achieve superior performance but also to offer the user an acoustic headset that is smaller than equivalent units currently available on the market. Housed in an IP67 enclosure, the unit, which is used in conjunction with a high voltage surge generator, can easily contend with wet conditions.
-
Product
Line Scan Sensors
-
The CMOS line scan image sensor family from ams consists of 23 variants, offering a range of resolution and pixel size specifications. Resolution options range from 2kpixels up to 16kpixels and line rates extend up to 80,000 lines/s.
-
Product
Extenders & Line Drivers
-
Extenders and Line Drivers enable reliable, long distance signal transmission over coaxial, twisted pair, or fiber optic cabling.
-
Product
Fault Locators
-
For the first time, you can detect the type of fault and locate the position of an electrical fault that causes intermittent or persistent circuit breaker trips, thus giving you the critical information needed to reduce call backs for circuit breaker trips.
-
Product
M-Power-line
-
The M-Power-Line convinces with its robust design, high efficiency, compact dimensions and excellent price-performance ratio. By using a Power Factor Controller (PFC) the input voltage may vary from 100V to 254V. This means that the devices can be used anywhere in the world regardless of the typical national power supply system. The simple operation and easy readability of relevant characteristic values (target/actual/state/alarm message) make the devices particularly attractive for use in many branches of industry as well as research institutes.
-
Product
Fault Simulation
Concurrent Fault Simulator
-
TurboFault combines high performance, versatility and accuracy. It is highly competitive with hardware accelerators for classical test fault grading. It supports synchronous and asynchronous designs at the gate level, including tri-state gates, latches, flip-flops, single and multi-port RAMs, complex bus resolution functions, and User Defined Primitives (UDPs).
-
Product
PLC Line Traps
-
Line Traps are used in transmission and distribution networks and they are the key components in Power Line Carrier (PLC) systems used for remote control signals, voice communication, remote metering and control between substations in the electrical T&D networks.
-
Product
Fiber Visual Fault Locator
-
Fiber visual fault locator is a pen type device which is able to locate the breakpoint, bending or cracking of the fiber glass,this small fiber optic equipment can locate the fault of OTDR dead zone and make fiber iIdentification from one end to the other end .
-
Product
Sequence / Rotation Indicators
-
Phase Sequence and Motor Rotation meter detects live phase and sequence orientation of three phase power sources and industrial equipment conductors to ensure proper installation. Motor rotation function identifies rotational direction of industrial equipment such as motors, compressors and generators. Non-Contact Motor Rotation feature determines rotation of running single-phase and three-phase motors without the use of leads.
-
Product
USB Line Camera
-
The USB Line Camera is an easy-to-use cost-effective board-level line scan camera. It consists of two circuit boards, the main circuit board and the sensor circuit board.
-
Product
Fault Locator
WEEZAP
-
WEEZAP is an LV vacuum circuit breaker combined with advanced measurement and protection capability.
-
Product
Load Cell Indicator
-
Morehouse Instrument Company Inc.
This indicator can read mV/V and use free, custom Morehouse software to convert the mV/V units to engineering units with coefficient files from ASTM E74 or ISO 376 reports. This meter is often the choice for accredited calibration service providers that want high accuracy and convenience but do not want to break the bank.
-
Product
PXI Single Bus 32-Ch 2A Fault Insertion Switch
40-190B-201
Fault Insertion Unit
The Single Bus, 32 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally closed through relays, so in the default state, there is a path between input and output for all signal channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
Line Tester
CAT 1 TEST
-
Monacor International GmbH & Co.
Line tester for continuity testing of Cat 5, Cat 6 and ISDN network cables*Connection test with LED display for 8 individual wires and shielding*Continuity, miswire, open, short, crossover, and ground detection*Connector compatibility with the following modular plugs: RJ45 (8P8C), RJ12 (6P6C), RJ11(6P4C, 6P2C)*Network standards supported: Token Ring, 10Base-T, 10Base-T2, 285A, TIA568A/568B*Separate receiver for particularly long and complex cables*The main unit and separate receiver can be attached to one another using a guide rail on the side*Power supply via 9 V block battery (not included)*Supplied with protective bag
-
Product
Visual Fault Locator
-
Shanghai Baudcom Communication Device Co.,Ltd.
This Pen-type VFL is specially designed for field personnel who need an efficient and economical tool for fiber tracing, fiber routing and continuity checking in optical networks. It finds breakpoints, poor connections, bending or cracking in fiber optic cables
-
Product
Voltage Indicator
-
Small installation devices for measuring both alternating and direct voltages.
-
Product
Angle Indicators
-
Computer Conversions Corporation
This series of units were designed to satisfy Hi speed multiturn synchro/resolver applications where the output data must be fresh and no data staleness can be tolerated. The tranducers utilized are the same as in the regular MDS series, however different tracking electronics are used. The resultant data tracks the input shaft perfectly and is always fresh and accurate at input speeds up to 64 revolutions per second, depending on the resolution. Data in BCD or Binary formats are available, and clean, unambiguous crossovers are guaranteed.
-
Product
Economic Type Frequency Indicator
CS1-RL
-
CS1-F economic type Frequency Indicator has been designed with high accuracy measurement, display and communication of Frequency.The innovation feature is auto-range input from 0.01Hz~ 100KHz (option ~140KHz) and the display resolution will auto-change to show the highest according to input frequency.They are also available 1 option of 1 Relay outputs, 1 Analogue output or 1 RS485 (Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission or communication for a wide range of panels and testing applications.
-
Product
Square Root - Gauge Line Error Indicators
-
Parker PGI's SRE6 and GLE6 Indicators are designed to quantify Square Root and Gauge Line Errors in natural gas orifice flow measurement. They identify inaccuracies caused by compressor-induced pulsation and differential pressure discrepancies.
-
Product
AC Line Separator
Model ALS-1
-
Kusam Electrical Industries Limited
With the aid of the AC line separator, the AC current from any appliance can be determined by plugging the appliance directly into the separator. By doing so, you are able to separate the neutral from hot / live conductor.
-
Product
Transmission Line Probes
-
Transmission line probes are a special type of passive probe designed for use at very high frequencies. They replace the high impedance probe cable found in a traditional passive probe with a precision transmission line, with a characteristic impedance that matches the oscilloscope input (50 Ohm). This greatly reduces the input capacitance to a fraction of a picofarad, minimizing the loading of high frequency signals. A matching network at the tip increases the DC input resistance. While they have lower DC input resistance than a traditional passive probe (usually 500 Ohm) to 1kOhm), the input impedance of these probes remains nearly constant over their entire frequency range. A traditional /10 passive probe will have a 10 MOhm) input impedance at DC, however this impedance drops rapidly with frequency, passing below the input impedance of a transmission line probe at less than 100 MHz.
-
Product
Visible Fault Identifier
TVFI
-
The Yamasaki TVFI Visible Fault Identifier is a practical palm sized solution for finding breaks, bends and faulty connectors or splices in fiber optic cable.
-
Product
Line Scan Cameras
-
STEMMER IMAGING offers one of the most comprehensive ranges of line scan cameras and vision systems for industrial and non-industrial applications.
-
Product
Polarity Indicator Circuit Tester
CT8007
-
No ground wire means no wire tangles nor time lost searching for grounding points. High Impedance electronic circuitry. Negligible current draw ( 1 microampere) is 30,000 times less than regular lamp type testers. This gives complete safety when working around sensitive electronic control modules and sensors. Operating range between 6 and 28 Volt DC in battery powered systems
-
Product
Temperature Indicators
-
Our inventory of temperature indicators features highly accurate devices for virtually every temperature measurement application. An indicator works in combination with compatible sensors to display measured temperature. The devices are staples in production and lab environments, monitoring and displaying crucial temperature changes. Each device will either come with a built-in sensor or will accept input sensors or probes. Depending on the model, an indicator may be integral to quality control during production, storage and distribution. Reference-grade indicators can accurately verify temperature calibrator performance. They can also display precise temperature changes during a process application.
