-
product
Thermocouple Thermometers
These industrial instruments’ claim to fame is their accuracy. General offers a wide variety of thermocouple thermometers distinguished by features such as the number of independent channels supported (from one to twelve) –such as the DT4208SD 12 Channel ThermoCouple Thermometer, ruggedness (the ability to survive a fall) – such as the Rugged DT62 Two Channel Thermocouple Thermometer, compatibility with one or more thermocouple types – such as the DT80-2 Two Channel “K” & “J” Thermocouple Thermometer, and data logging capability – such as the DT4947SD 4 Channel Thermocouple Thermometer with Excel Formatted Data Logging SD Card. Our portfolio of thermocouple probes is just as extensive.
-
product
Compatible Bi-Directional Serial Data Interface
PMC-BiSerial-IO-II
The PMC BiSerial has been updated to be even better. Building on the knowledge and experience gathered from multiple IP and PMC BiSerial implementations and adding in the latest technology has created the PMC-BiSerial-II. The BiSerial II features completely isolated FIFOs with 32 bit ports for increased adaptability and performance.
-
product
FMC Card with DisplayPort Input and Output
TEF0007-02A
Sundance Multiprocessor Technology Ltd.
The Trenz Electronic TEF0007 is a DisplayPort 1.2 compatible FMC card with data rates up to 5.4 Gbps and sink and source DP connector. SN65DP159 is used as DP Retimer and SN75DP130 as DP Redriver to connect sink and source to on board Kintex-7 FPGA.Image stream over FMC can be realized over 4 MGTs (only 1 available on LPC) and 34 differential IOs (LPC compatible).
-
product
3U CompactPCI 8-port Serial Communication Module
cPCI-3548
- Supports 32-bit/33MHz CompactPCI bus- 16C550A compatible serial communication controller- Eight RS-232/422/485 asynchronous communications ports with intelligent buffer- 2500 VDC signal to ground isolation voltage- Auto-flow control; change mode by dip switch- Plug-and-play, IRQ & I/O address automatically assigned by PCI BIOS, shared IRQ- Surge protectors; rugged DB-62 connector
-
product
Ultra-Performance Motherboard Module
ProDAQ 3180
The ProDAQ 3180 ultra-performance motherboard is a register-based VXIbus device supporting single-word transfer and block transfer of 16-bit and 32-bit words. It can be configured for both the A16 and A32 address space. The improved VXIbus interface of the ProDAQ 3180 is compatible to the VXI-1 Rev 4.0 standard and supports the 2eVME and 2eSST protocols, which allow for backplane transfers at data rates of up to 320 MB/s (theoretically). Depending on the slot-0 controller used, the ProDAQ 3180 can sustain data transfers up to 240 MB/s.
-
product
PCIe-8430, PCI Express, 8-Port, RS232 Serial Interface Device
780591-01
The PCIe‑8430/8 is a high-performance interface for high-speed communication with RS232 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. NI serial interfaces also appear as standard … COM ports for compatibility with programs that use serial communications.
-
product
Module Spectrum
nRF52811 Series
Raytac nRF52811 module employed MDBT42Q series design is a hardware pin to pin compatible to nRF52832 & nRF52810 solution with both Chip Antenna and PCB Antenna option for selection.
-
product
Chip Obsolescence Solutions
Solve component obsolescence problems with an Ironwood adapter and an alternate device. Adapters convert the pinout of an alternate device to maintain compatibility with an existing footprint – no need to redesign a new circuit board. Very often, these adapters (called Package Converters) are a simple 1:1 pin mapping from the new package to the old. Here are a few examples of package converters and how they can solve chip obsolescence issues.
-
product
8-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB116
The FAB116 features a PICMG 1.3 CPU card slot, one PCIe x16 slot, three PCIe x4 slots, three PCI, and built in a 24-pin ATX power connector and 8-pin connector for thermal detected board. Two high speed USB 2.0 ports are featured. The FAB116 is compatible with Axiomtek's AX60551 and AX60552 chassis.
-
product
NI-9423, 24 V, 8 Channel (Sinking Input), 1 µs C Series Digital Module
783735-01
24 V, 8 Channel (Sinking Input), 1 µs C Series Digital Module - The NI‑9423 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with 24 V logic levels, can accept up to … 30 V discrete logic levels, and has an LED that indicates the status. The NI‑9423 offers isolation between the input and output banks from channel to earth ground. The NI‑9423 is a correlated digital module, so it can perform correlated measurements, triggering, and sychronization when installed in a CompactDAQ chassis.
-
product
2-Ch Sensor Amplifier
SR-2210
The SR-2210 sensor amplifier accepts constant-current line drive sensors and connects the signal to analyzers and recorders that would not otherwise be compatible with constant-current sensors.The units connects directly with BNC connectors to ONO's model MI-3111 microphone preamplifiers and NP-3000 series of accelerometers.With compact, light-weight, battery operation, it can save for preparation of measurement.
-
product
85W - Single Output
iCH Series
*DOSA Compatible Footprint*4.5-14 Vdc Input*0.7-8.5 Vdc Output*Non-Isolated*Excellent Transient Response*No external loop tuning components needed
-
product
Isolated Digital I/O Card
mPCIe-IDIO-8
The mPCIe-IDIO-8 consists of a type F1 PCI Express Mini Card (mPCIe) interface board that connects to a Mobile-ITX-sized, DB-37M Isolation Module via an included 9” cable. That module is designed to be easily panel-mounted in any application environment. It uses the high speed PCI Express bus to transfer digital data to and from the card. The digital I/O is compatible with 8255 PPI chips making it easy to program.
-
product
Universal Programmer Superpro 7500
Until now,Support 396 IC manufacturer, 94596 pcs devices and keeps growing.Support devices with Vcc from 1.2V to 5V. The programming speed up further increase 30% compared to SUPERPRO 5000.The programmer support files up to 256 GBytesBuilt with 144 universal pin-drivers.Universal adaptors are available for varies packages up to 144 pins. New device support will be easier. PC hosted mode and stand-alone mode. Under PC hosted mode the programmer is controlled by a PC via USB2.0 (high speed) to program a chip. Under stand-alone mode the programmer is controlled via the 6-KEY keypad and the 20 character by 4 line LCD display. A SD card is used to store the project files.User can operate multiple units to construct a concurrent multiprogramming system thank for the stand-alone mode. Only IC manufacturer approved programming algorithms are used for high reliability. (+5%~-5%) and (10%~-10%) Vcc verification enhances programming reliability.Advanced and powerful functions.Production mode start chip operation at the moment the chip is inserted in the socket properly.Project function simplifies processes such as device selection, file loading, device configuration setting, program option, and batch file setting into one touch step.Password can be set for project files and production volume controlBatch command combines device operations like program, verify, security into a single command at any sequence.Serial numbers generators are available as standard or customer-specific functions.Log file is useful for quality tracking. Over-current and over-voltage protection for safety of the chip and programmer hardware. WINDOWS XP/Vista/Win7/Win8/Win10 32/64bit compatibility
-
product
Enclosure, 9050, Hinged Cover, 12" Depth
410112519
Enclosure, 9050, Hinged Cover, 12" DepthNot compatible with 9050 ITA frame p/n 410104110 or any older model 9050 ITA frame not matching the current height of 9050 ITA frames of 14.57". Questions? Contact Us before purchase.
-
product
Optical Spectrum Analyzers
Thorlabs' Optical Spectrum Analyzers (OSAs) perform highly accurate spectral measurements. Compatible with fiber-coupled and free-space light sources, these compact benchtop instruments suit a wide variety of applications, such as analyzing the spectrum of a telecom signal, resolving the Fabry-Perot modes of a gain chip, and identifying gas absorption lines.
-
product
4-Channel 1.25 GHz, 16-bit D/A with Virtex-6 FPGA - 3U VPX
Model 52670
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 1.25 GHz 16-bit D/As- Four digital upconverters- Programmable output levels- 250 MHz max. output bandwidth- 2 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- Dual µSync clock/sync bus for multimodule synchronization- User-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- 3U VPX form factor provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
product
SH37F-P-4, 37-Pin Female to Pigtail Shielded I/O Cable, 12ft
778620-04
37-Pin D-SUB Female to 37-Pin Bare Wire Female, 12 ft, Pigtail I/O, Shielded Multifunction Cable - The SH37F-P-4 connects compatible CompactRIO modules to accessories or cables with bare wire connectors.
-
product
Software For Protective Relay Testing
TDMS Pro
TDMS Pro is the NEW software platform designed to efficiently run tests and manage test data of almost any kind of electromechanical and digital relay from any manufacturer.From the simplest to the most complex type, TDMS Pro, with a completely new graphic interface and advanced test functions, can be used to test all types of multifunction protection relays installed in power transmission and distribution networks, in power plants and industries. The universal test set compatible with TDMS Pro are: DRTS 66, DRTS 64, DRTS 34 and DRTS 33.
-
product
4 GHz, 20 GS/s, 4ch, 100 Mpts/Ch High Definition Mixed Signal Oscilloscope
WavePro 404HD-MS
HD4096 technology provides 12-bit resolution up to 8 GHz and 20 GS/s.Up to 5 Gpts of acquisition memory enables detailed viewing of long events.15.6" 1900 x 1080 Full HD capacitive touchscreen.New ProBus2 input supports up to 8 GHz bandwidth and direct compatibility with a wide variety of existing ProBus probes - 50Ω and 1MΩ coupling modes support all input types on a single connector.MAUI with OneTouch user interface for intuitive and efficient operation.Deep toolbox enables and simplifies complex analysis.Intuitive navigation to quickly find important features in long waveforms.Zone Trigger – Simple Triggering for Complex Signals.
-
product
AirLink Interface
PS-3200
This economical interface makes PASPORT sensors cross-platform compatible.
-
product
USB BUS Controller Board
MS 1711
- 8 bit and 16 bit compatible Read and Write Cycles- Single or Block Memory and IO Write Cycles- Interrupt Cycle Generation- The generated bus cycles signals is compatible with ISA96 system back plane- External Reset- Double Euro Standard Board- Driver interface for Windows2000/XP/VISTA and LINUX OS
-
product
6U CompactPCI Rear Transition Module With Intel® Ethernet Controller I350-AM2 - CPCI-6100 Series
20040265
The CPCI-R6100 Series Rear Transition Module is compatible with ADLINK 6U CompactPCI processor blades and include Intel® Ethernet Controller I350-AM2.
-
product
LGA 1200 Intel® Xeon® W & 10th Gen.Core™ Proprietary Server Board with 4 x DDR4, 1 x PCIeX16, 2 x PCIeX4, 5 x USB 3.2, 3 x SATA 3, Quad LANs and IPMI
ASMB-610
- Proprietary server board with LGA 1200 Intel® Xeon® W & 10th Gen. - Core™ i9/i7/i5/i3 processors- Compatible with HPC-61 series chassis- DDR4 2933/2666/2400 MHz ECC/Non-ECC UDIMM up to 128 GB- One PCIe x16 slot or two PCIe x8 slots support FH/10.5" Length Cards- Two PCIeX4 slots support low profile expansion cards- 3x SATA 3 ports and 5x USB 3.2 ports- One M.2 2280/2242 (SATA / PCIe compatible)- Quad LAN with Intel I350- Flexible IO board design
-
product
Kestrel /QX
0149-QX
Quad+ speed Windows/NT Kestrel Co-Processor for four times the speed of the Kestrel /SX. Occupies one PCI slot. A writable control store, FPGA implementation of the HP1000 architecture with 4 MBytes of tightly coupled, zero wait-state memory. Includes compatible hardware floating point. On-card x86 microprocessor rapidly processes "virtual" I/O instructions. PCI bus speeds increase disk throughput by at least a factor of ten. HP1000 Bus support logic for non-emulated devices is provided on-board with connector to wide bandwidth fibrechannel adapter. Operates only under Windows/NT. WNT Support license included.
-
product
PCB Adapter, Receiver, SIM, VTAC, 40 Pos, 6 Slot, to (1) HDMI
510170113
A small, modular PCB board that connects high speed digital inserts (VTAC) to a single HDMI connector. Great for COTS cable configurations. Compatible with all VTAC/SIM receiver modules.
-
product
PS/2 Type; ATX 400W
PS400-XP2
*Input Range: 90 ~ 264VAC Full Range*Output Voltage:**+5V, 20A (0.5A min)**+3.3V, 20A (0.3A min)**+12V1, 16A (1A min)**+12V2, 16A (1A min)**-12V, 0.5A**+5Vsb, 2.5A (1A min)*MTBF(hours): At 25°C, 100,000h*Safety: TUV, CS22.2 NO.60950-1, IEC, UL, NEMKO+CB, CE*Dimensions: 150 x 140 x 74 mm*Compatible with Axiomtek products: AX61221/AX61222/AX60501/AX60551/AX60552/AX61400/AX6145/AX6156/AX61492/AX61220
-
product
SparkFun MicroMod Teensy Processor
The SparkFun MicroMod Teensy Processor leverages the awesome computing power of the NXP iMXRT1062 chip and pairs it with the M.2 MicroMod connector to allow you to plug it into your choice of compatible MicroMod Carrier Board. With the M.2 MicroMod connector, connecting your Teensy Processor is a breeze. Simply match up the key on your processor's beveled edge connector to the key on the M.2 connector and secure it with a screw (included with all Carrier Boards). Adding a Teensy to your desired project has never been easier!
-
product
High End Portable Laser Power/Energy Meter
Centauri Single Channel P/N7Z01700
*Compatible with all standard Ophir Thermal, BeamTrack, Pyroelectric and Photodiode sensors*Large 7" Full Color Touch Display*Multilingual interface – English, French, Spanish, Italian, German, Russian, Japanese, Chinese and Korean*Single and Dual Channel models available*Various Displays: Bargraph, Analog Needle, Line Plot, Pulse Chart, Pass/Fail, Position, Stability, and Real Time Statistics*Dual Channel Instrument supports Split and Merged Graphical Displays*Sophisticated power and energy logging, including logging every pulse at up to 25000Hz with Pyro sensors*Math functions: Density, Scale Factor, Normalize against base line, etc. Functions can be mixed together, displayed graphically, and can also be logged
-
product
2-CH Pulse-Train Motion Control EtherCAT Module
EPS-7002
ADLINK" s EPS slave system features modular design for flexible high channel density, rugged construction, easy maintenance, and intelligent performance, compatible with 3rd party EtherCAT products. Precise time-deterministic control enables I/O synchronization for critical applications, and FPGA and ARM technology allow users to fully monitor status of EPS modules and systems, including operating temperature and usage cycle of relay switching, as well as motion control status for general purpose motor drive control. In addition, the ADLINK EtherCAT configurator enables auto-scan and configuration across EtherCAT systems. The EPS" unique structural and electronic design supports hot-swappable function, reducing repair time, and the rugged construction and operating temperature range of -20°C to 60°C allow operation in the harshest environments.





























