-
product
Microwave and mmWave
Tx/Rx
Analog Devices offers complete transmitter (Tx) and receiver (Rx) solutions for microwave (w) and millimeter wave (mm wave) applications. With the need for greater integration and improved performance in multiple industries and technologies, Analog Devices' industry-leading, ready to use transmitter and receiver chipsets for E band, V band, and microwave applications help designers reach new limits in their radio designs. This product family's integrated chipsets can be used for backhaul communications, VSAT, small cell networks, broadband local networks, and other applications.
-
product
CMOS SoC for mmWave 3D Imaging Sensor
.
Vayyar chip covers imaging and radar bands from 3GHz-81GHz with 72 transmitters and 72 receivers in one chip. Enhanced by an integrated, high-performance DSP with large internal memory, Vayyar’s sensor does not need any external CPU to execute complex imaging algorithms.
-
product
mmWave Sensors
The world’s most precise millimeter wave sensor available today on a single chip. The world’s most precise millimeter wave sensor available today on a single chip. TI’s CMOS single-chip sensors integrate an RF front-end with a DSP and MCU.
-
product
Balanced Upconverters
Are used to create a mm-wave signal by combining a lower RF frequency with a higher mm wave frequency.
-
product
Millimeter Wave Antenna Testing
If you are involved in antenna or system level design using mmWave or THz frequencies, then you understand the importance of dependable testing equipment. It may be that you are designing passive phase array or that you are designing a mmWave radar sensor system, but when it comes to validation of your design, simulation can only bring you so far. Phased array antennas have to be measured over the air (OTA) to ensure the radiation pattern of your design efficiently conducts energy in the right direction which is where the MilliBox comes in.
-
product
Conformance Test Solutions 3GPP / Regulatory (CTIA / RED)
Only conformance test sytems from Rohde & Schwarz cover all relevant digital mobile device generations.The key to success is comprehensive access to RF, RRM, LBS and PCT test cases as defined e.g. for 5G NR in 3GPP TS 38.521-1 to -4 (5G NR RF), 38.533 (5G NR RRM), 38.523-1 (5G NR PCT), 37.571 (LBS).The Rohde & Schwarz conformance test solution portfolio consists of approved test platforms for device certification by GCF and PTCRB that support both TDD and FDD and all relevant 5G NR bands in both sub-8GHz (FR1) and mmWave (FR2) frequencies, as well as all frequency bands for LTE, WCDMA and GSM.
-
product
Antennas
Our broad portfolio of antennas includes products designed for cellular, broadcast, navigation, RFID, IoT, DAS, mmWave, and more. Our antennas are available in standard and custom designs and engineered for use in cars, heavy-transport vehicles including rail, and a wide variety of personal electronics, including mobile device and wearable technology. Our antennas offer high-quality transmission for a wide variety of frequencies including, but not limited to Bluetooth, WLAN, and ZigBee. We manufacture our antennas in facilities worldwide, which include testing capabilities in near and far field patterns, scattering parameters, SAR, vibration, humidity, temperature shock, salt fog, throughput, and acoustic. We also manufacture antenna assemblies.
-
product
E- And W-Band Test Assembly
StormFlex® 047EW
An SF047EW assembly offers test engineers, application designers, manufacturers of mmWave applications the proven durability and robustness of Storm Flex® 047 cable, optimized for coaxial connectivity at frequencies up to 110 GHz.SF047EW cable can withstand handling and flexing and while maintaining the original Insertion Loss and VSWR performance at frequencies previously addressed by waveguides.
-
product
Test Contactor/Probe Head
xWave
Highest performance and most robust RF broadband production solution for package, wafer, or Over-the-Air (OTA) test for 100 GHz.The xWave™ test contactor / probe head utilizes patented hybrid contacting technology to optimize RF performance and provide robustness for production testing of the most challenging cmWave and mmWave devices. Inside the xWave test contactor / probe head are embedded patch antennas and coplanar waveguides for both wireless and wired communication.
-
product
Oscilloscope 10 GHz, 4 Channels, 3.5 mm
UXR0104B
UXR0104B Infiniium UXR-Series, is the 10 GHz, 4 channel, Infiniium UXR-Series real-time oscilloscope with the most comprehensive set of probing, analysis applications, and measurements for advanced technologies. EVM performance for wideband mmWave measurements that rivals even the best signal analyzers. UXR-Series scopes have flexible upgrades: Bandwidth up to 110GHz, Memory up to 2Gpts, DDC up to 2.16GHz, and configurable frequency extensions up to 10GHz.
-
product
5G Channel Sounding, Reference Solution
The 5G Channel Sounding, Reference Solution is a combination of hardware, software, and measurement expertise providing the essential components to accelerate 5G sounding research. This reference solution enables researchers and design engineers to use, enhance, or modify the test platform as required to meet specific test application needs including scalable channel count, flexibility to transmit and measure in mmWave frequencies, wide transmit and analysis bandwidths, and real-time data processing.
-
product
Limiters - RF / Microwave / MmWave
PMI offers a variety of limiters covering the DC to 62 GHz frequency range. PMI's limiters offer low loss, high speed along with low leakage levels and high peak power handling. If you do not see exactly what you need, please e-mail your requirement to sales@pmi-rf.com so we can propose an instant solution.
-
product
Remote Radio Head
CMPHEAD
The separate one-box tester and the R&S®CMPHEAD30 RRH concept allow short RF cable lengths for an optimal link budget in radiated test environments. This approach enables testing of fully assembled FR2 devices and RFICs with both IF and mmWave RF interfaces. The multi-band R&S®CMPHEAD30 covers all important FR2 bands
-
product
CMPQ
To meet the measurement challenges of 5G device testing in the mmWave (mmW) frequency spectrum Rohde & Schwarz offers the R&S®CMPQ, a fully integrated solution from a single supplier. The R&S®CMPQ consists of the R&S®CMP200 radio communication tester, the R&S®CMPHEAD30 remote radio head and the R&S®CMQ200 shielding cube. The R&S®CMPQ provides accurate and reliable measurement results under radiated conditions.
-
product
Optimize Throughput And Cost For MmWave 5G Device Functional Test
Test engineers always have faced tough new test-coverage challenges. Those introduced by 5G measurements at mmWave are no exception, as they require over-the-air (OTA) radiated test solutions. But never have these pressures seen today’s intense time-to-market, manufacturing volume, and operational expectations! A solution that meets these demands must:
-
product
Detectors
ZBD
VDI offers zero biased detectors (ZBD) for a variety of mmWave and THz applications. These detectors offer full band performance without bias.
-
product
900 Hz to 110 GHz PNA MM-Wave System
N5290A
Single-sweep solution with compact frequency extenders Purchase as a single product solution Accurate leveled power can be applied to the device, providing the ability to sweep power Available various software application for detail analysis Every spec verified, adjustments included Lock in support & peak performance from the start
-
product
Waveguide Bends
Fairview Microwave’s lines of precision waveguide bends are widely used in applications such as high efficiency RF, microwave and mm-wave transmissions, satellite and military communications, radar, telecom, instrumentation and test benches. In waveguide systems that require a signal to turn or bend 90 degrees, Fairview’s waveguide bends are used to facilitate that bend or turn without degrading the transmission signal. These WG bends operate from 5.85 GHz to 90 GHz across 12 frequency bands and are available in sizes from WR-12 to WR-137. This family of waveguide bends also boast low loss and VSWR as low as 1.08:1 and are available in both E-plane and H-plane configurations. They are constructed using gold plated, oxygen free hard copper (OFHC) or painted copper alloy depending on the model and are also offered with either a UG-style flange per the military standard or a CPR-style flange. Many models are RoHS compliant.
-
product
Rack-Mountable CATR Chamber for 5G NR mmWave Signals
ATS800R
The R&S®ATS800R CATR based 5G NR mmWave test chamber provides a very compact over the air (OTA) testing environment for testing 5G FR2 antennas, modules and devices in R&D. The R&S®ATS800R has a very small footprint and wide frequency range, and offers maximum functionality and test coverage in a small space. The flexible setup options and range of extensions make the R&S®ATS800R a solid and future-proof environment for your FR2 testing needs.
-
product
E Bend Waveguide
E-plane waveguide bends are sections of high-precision crafted waveguides and shaped to either 30º, 45º ,60º, or 90º angles for e-plane needs. It directs the radio frequency beam and “bends” the signal to go the direction you want. Think of it like Tokyo drifting around a corner in your car. Precision MMW will help you with the highest quality E bend waveguides. We are a millimeter wave spectrum manufacturer of various active and passive mmWave products and sub-system engineering.View more E Bend Waveguide
-
product
Carrier Acceptance Test Solutions for Network Operators
The Rohde & Schwarz carrier acceptance test systems provide access to the most important test plans of the world’s major mobile operators.Voice over NR, data throughput, protocol, positioning, RF, RRM and application testing – all relevant test scenarios are available on a common hardware platform.The entire range of 5G NR testing modes are available, covering sub-8 GHz (FR1) and mmWave (FR2) frequencies, and both non-standalone (NSA) and standalone (SA) modes.Contact your Rohde & Schwarz sales representative to learn more about the latest products and features.
-
product
RF Analog Signal Generators
The right solution for your requirements from the broad analog signal generator portfolio of Rohde & Schwarz.With the analog signal generator portfolio we cover the wide range of RF, microwave and mmWave frequencies.Our selection of analog signal generators is characterized by the outstanding signal purity and performance as well as their functionality of the solutions; whether in the high end or midrange area.The solutions benefit industries such as RF semiconductor, wireless communications, aerospace and defense, and also covers tasks featuring development, production and service, and more.
-
product
Pulsed And CW ESR/EPR: Quasi-continuous Powerful Millimeter (mm-wave) And Sub-millimeter (sub-mm Wave) Orotron Generator
Insight Product Company offers Quasi-continuous powerful millimeter (mm-wave) and sub-millimeter (sub-mm wave) Orotron Generators which can be used for both continuous wave (CW) and pulsed electron spin resonance (ESR) and electon paramagnetic resonance (EPR) experiments.
-
product
900 Hz to 120 GHz PNA MM-Wave System
N5291A
Single-sweep solution with compact frequency extenders Purchase as a single product solution Accurate leveled power can be applied to the device, providing the ability to sweep power Available various software application for detail analysis Every spec verified, adjustments included Lock in support & peak performance from the start
-
product
Detector Mount
DMXE
The DMXE Detector Mounts are broadband devices designed for operation in millimeter wave range. The Detectors are optimized for broadband performance and are used in mm-wave test setups to detect, monitor and measure modulated signals.The DMXE Detector Mounts use Schottky Barrier packaged diodes and are provided in five waveguide bands between 33 GHz and 225 GHz.
-
product
Test Contactor/Probe HEad
cRacer
The cRacer™ test contactor and probe head portfolio offer solutions for 5G mmWave FR2 up to 54+ GHz.cRacer utilizes robust spring probe technology for testing singulated packages or probe heads for wafer probe (bumped/pad) applications with fine pitch and WLCSP compatibility – ranging from 100 µm to 650 µm, covering the majority of 5G devices.cRacer features a stainless-steel spring for tri-temp testing and performance in operating temperatures -55°C to +155°C.
-
product
Medium-size Compact Antenna Test Range
H-Series CATR
The H-Series CATR chamber provide complete 3D performance assessment for 5G OTA devices and antennas including gain, efficiency, directivity, polarization and beam characteristics for frequencies from 3 up to 110 GHz, capable of supporting forthcoming 5G Sub-6 GHz (from 3 to 6 GHz) and mmWave (24 to 110 GHz) standardized testing including TRP/TIS, EIRP, EIS, IBB and emissions in accordance to 3GPP TR38.810 and TR37.842.
-
product
UXA Signal Analyzer, 2 Hz to 110 GHz
N9042B
Test the real performance of your millimeter-wave (mmWave) innovations in 5G, satellite, radar, and more with our N9042B UXA X-Series signal analyzer and measurement applications. The N9042B provides the industry's widest analysis bandwidth and deepest dynamic range to help you solve your most difficult mmWave challenges — tight design margins and timelines, complex modulation, and stringent standards.
-
product
Planar Doped Barrier Detectors
KRYTAR Planar Doped Barrier Detectors are specifically designed for use in today's high-performance microwave instrumentation and systems. KRYTAR detectors are designed for such applications as power measurements, analyzing radar performance, leveling pulsed signal sources, AM noise measurements, system monitoring and pulsed RF measurements in ultra-broadband and mm-Wave applications.
-
product
mmWave and Microwave GaAs Frequency Dividers and Prescalers
Keysight Technologies provides MMIC frequency dividers and prescalers ideal for high-frequency communications, microwave instrumentation, and electronic warfare (EW) radar system applications. These devices operate from DC to 16 GHz and provide a large input power sensitivity window and low phase noise.
